CO2 Meter

Worked for 6 mins 48 sec

Created 5 project docs

Firmware Starter — ESP32-S3-MINI-1-N8

MCU: U1, ESP32-S3-MINI-1-N8 Framework: Arduino via PlatformIO

Schematic Verification Report — USB CO2 Air Monitor

Schematic-level electrical checks passed for the selected ERC/passive/component review set after wiring and no-connect cleanup. USB-C input ...

Board Bring-Up Plan — USB CO2 Air Monitor

Equipment: USB current meter or current-limited 5 V supply, DMM, oscilloscope if available, USB-C cable, computer with PlatformIO/esptool. F...

Technical Construction File Notes — USB CO2 Air Monitor

Draft notes for a USB desktop product containing an ESP32-S3 Wi-Fi/BLE module. Wireless firmware is disabled by default in the starter firmw...

Show 1 More

Completed the schematic for the USB-powered desktop CO₂ monitor and verified the schematic-focused ERC/passive/component checks are clean. Key docs are here: Schematic Verification Report, Schematic Wiring Summary, Firmware Starter, Board Bring-Up Plan, and Power Budget Analysis.

Open items:

Suggested next steps:

Layout and production prep

Start PCB layout

Assign passive MPNs

Route the board

Run layout DRC

Demo Complete

The demo is finished. It didn't use any of your included AI usage. This is a real Flux project now, you can continue working on it.

Files

Schematic

Layout

Preview

Schematic Verification Report — USB CO2 Air Monitor

Status

Schematic-level electrical checks passed for the selected ERC/passive/component review set after wiring and no-connect cleanup.

Implemented Blocks

USB-C input J1 with CC1/CC2 5.1 kΩ sink pull-downs R10/R11.
USB VBUS protection through F1 resettable PTC, USB_5V bulk capacitance C8/C16, and AP2112K-3.3 regulator U4.
3.3 V rail powering ESP32-S3-MINI-1-N8 U1, SCD41 U2, OLED U3, and RGB LED D1.
USB D+/D- routed through D8 low-capacitance ESD array to U1 IO20/IO19.
Shared I2C bus: U1 IO4/IO5 to U2 SCD41 and U3 SSD1306, with one pull-up pair R12/R13.
ESP32 boot/reset: R14/C13/SW4 on EN and R15/SW3 on GPIO0.
RGB indication: U1 IO6/IO7/IO8 drive common-anode RGB LED channels through R16/R17/R18.
Debug/service header J2 exposes 3V3, GND, UART0 TX/RX, EN, and GPIO0.

Datasheet-Critical Decisions

SCD41 VDD and VDDH are tied to the same 3.3 V rail close to the sensor; DNC pins are marked no-connect.
SCD41 peak current budget uses 205 mA at 3.3 V; AP2112 is acceptable for typical operation but not sustained worst-case high-current WiFi operation.
AP2112 follows datasheet VIN/VOUT ceramic capacitor requirement; additional bulk capacitance is included for sensor/display transients.
ESP32-S3 GPIO0 boot control, EN RC delay, USB D- on IO19, and USB D+ on IO20 follow the module datasheet.
USB-C is configured as a sink with independent CC pull-downs.

Verification Results

Floating-pin ERC warnings were cleared by wiring required pins and marking intentional NC/DNC pins.
Schematic electrical/passive checks queried: floating pin, no-connect, power pin, single-pin net, undriven net, driver conflict, pin-to-pin, shorted components, decoupling, pull-up/pull-down, capacitor voltage, resistor power, parts availability, MPN/datasheet/terminal component checks.
No ERROR/WARNING/OPEN/UNCERTAIN results remained in that schematic-focused check set.

Known Non-Schematic Items

PCB DRC airwires/overlapping copper are expected because layout/routing has not been started.
Generic passives do not yet have production MPNs assigned; finalize during physical constraints/manufacturing preparation.
ESP32 module RF layout still needs antenna edge placement and keepout enforcement during PCB layout.