Dual-Channel DisplayPort Design


Design me a schematic that will take a display port input with resolution 2560 by 720 and a the connector is for a flexi pcb. The display input is then split by a circuit/ IC so that half the resolution horizontally, 1280 by 720 pixels go to 2 matching circuits and each circuit has the Texas instruments DLPC3433. with 16bit colour RGB565 and the power driver is the DLPA2000
Created a project doc

Display Splitter Design Brief

View Document

Display Splitter Design Brief User-requested design
  • DisplayPort video input at 2560 × 720 pixels, arriving through a flex-PCB connector.
  • Split the image horizontally into two 1280 × 720 outputs: left half and right half, not duplicated full images.
  • Two matching downstream display circuits, each using a Texas Instruments DLPC3433 controller and DLPA2000 power/illumination driver.
  • Requested controller video format: 16-bit RGB565.
Current state
  • Requirements captured only. No component research, datasheet validation, schematic creation, or electrical verification has been performed.
  • Project remains empty: zero components and zero nets according to initial project context.
  • Execution stopped because the account ran out of ACUs.
I saved your requirements in Display Splitter Design Brief: a 2560 × 720 DisplayPort input through a flex connector, cropped into left/right 1280 × 720 RGB565 streams feeding two DLPC3433/DLPA2000 channels. No schematic components or wiring have been added.
Next, I need to verify TI interface and resolution compatibility, select the receiver/cropping architecture, and confirm your refresh rate, DMD/optical-engine model, flex pinout, and supply voltage; live research and schematic construction require Agent mode.
Execution stopped because your ACUs ran out.
What is Agent mode?
Agent mode lets Flux build, do deep research, validate designs, and work through complex assignments.
Chat mode is just as smart and has the same engineering knowledge, but it cannot work autonomously.
Only Agent mode consumes your plan's included AI usage (measured in ACUs).
Continue in Agent Mode

Waiting for input

No schematic yet

Talk to Flux to get started.

Display Splitter Design Brief
User-requested design
  • DisplayPort video input at 2560 × 720 pixels, arriving through a flex-PCB connector.
  • Split the image horizontally into two 1280 × 720 outputs: left half and right half, not duplicated full images.
  • Two matching downstream display circuits, each using a Texas Instruments DLPC3433 controller and DLPA2000 power/illumination driver.
  • Requested controller video format: 16-bit RGB565.
Current state
  • Requirements captured only. No component research, datasheet validation, schematic creation, or electrical verification has been performed.
  • Project remains empty: zero components and zero nets according to initial project context.
  • Execution stopped because the account ran out of ACUs.
Architecture to investigate (not validated or selected)
DisplayPort receiver → pixel-processing/cropping stage → two synchronized 1280 × 720 RGB565 video interfaces → two DLPC3433-based display channels with DLPA2000 support circuitry.
Do not assume that a passive DisplayPort splitter can crop the two image halves. Validate whether an integrated receiver/processor can implement the split or whether programmable logic and buffering are needed. Validate DLPC3433 supported video-interface widths, formats, timings, and supported DMD resolutions; RGB565 and 1280 × 720 compatibility have not been established. Validate DLPA2000 compatibility and all required power rails and sequencing from TI documentation before committing to the schematic.
Inputs still needed
  • Refresh rate and acceptable latency; these govern video bandwidth and buffering.
  • Selected DMD or optical engine for each channel, including exact part numbers.
  • Flex connector part number and source-side pinout, including DisplayPort lane count, AUX, HPD, grounds, and power if present. Connector geometry and pin mapping must be sourced before placement/wiring.
  • Available supply voltage and power budget, and illumination requirements.
  • Whether the source can provide the required 2560 × 720 timing and what EDID behavior is required.
Next work
  1. Confirm the missing system requirements and obtain authoritative TI controller/driver documentation.
  2. Validate the requested DMD resolution and RGB565 input mode before selecting the video-processing architecture.
  3. Select and verify the DisplayPort receiver and cropping/dual-output implementation, including clocking, synchronization, buffering, and firmware/configuration needs.
  4. Design two matched display channels and their power, illumination, reset, configuration, and programming circuitry.
  5. Capture the schematic and verify pin connectivity, power sequencing, interface timing, bandwidth, and electrical rules.
  • User-requested design

  • Current state

  • Architecture to investigate (not validated or selected)

  • Inputs still needed

  • Next work