ESP32 Universal Core Board Design


Bloqueado: tu cuenta no tiene ACUs disponibles, así que no puedo continuar ejecutando cambios de IA en el PCB ahora mismo.
Hecho en esta sesión:
  • Cambié la placa a PCB circular de 80 mm de diámetro.
  • Configuré intención de 2 capas.
  • Confirmé que los componentes caben en la placa, aunque el ruteo puede quedar algo congestionado cerca del ESP32.
Pendiente:
  • Reorganizar ESP32 y GPIOs en anillo radial circular.
  • Mantener antena hacia arriba con zona libre de cobre/componentes.
  • Reubicar potencia, UART, OLED/TFT, LEDs y botones para la versión circular.
  • Agregar serigrafía v2.0.
  • Enrutar y verificar DRC/ERC/airwires.
Reorganizar ESP32 y GPIOs en anillo radial circular.
Mantener antena hacia arriba con zona libre de cobre/componentes.
Reubicar potencia, UART, OLED/TFT, LEDs y botones para la versión circular.
Agregar serigrafía v2.0.
Enrutar y verificar DRC/ERC/airwires.
Bloqueado: tu cuenta no tiene ACUs disponibles, así que no puedo seguir ejecutando cambios de IA ahora mismo.
Hecho en esta sesión:
  • Reorganicé la PCB circular de 80 mm.
  • Dejé el ESP32-WROOM-32 centrado, con antena hacia arriba y zona libre.
  • Reubiqué los GPIOs en un anillo radial alrededor del ESP32.
  • Reacomodé potencia, UART, OLED/TFT, LEDs, botones y mounting holes dentro del círculo.
  • La colocación quedó sin solapamientos ni componentes fuera de la placa.
Pendiente:
  • Agregar/actualizar la serigrafía v2.0.
  • Enrutar la PCB.
  • Ejecutar ERC/DRC/airwire.
  • Corregir cualquier error que aparezca en la verificación.
Agregar serigrafía v2.0
Revisar antena manualmente
Listar airwires
Ejecutar ERC/DRC

Schematic is Auto-placed

The schematic has been arranged automatically. Flux can redraw it to be more readable, with components placed in related groups and wires drawn more legibly. This takes about 10-60 mins.

IAActiva ESP32 Universal Core Board v1.0 — Project Specification
Overview
Universal 2-layer ESP32-WROOM-32 development/prototyping PCB for IoT, robotics, automation, and embedded products. The design emphasizes maximum GPIO access, hand wiring via large solder pads, simple UART programming, and a copper-free antenna keepout.
Board Requirements
  • Board name: IAActiva ESP32 Universal Core Board v1.0
  • PCB size: 100 mm x 100 mm
  • Stackup: 2-layer FR4, 1.6 mm nominal thickness
  • Finish intent: black solder mask, white silkscreen
  • Mounting: four through-hole corner mounting holes
  • Silkscreen text:
    • IAActiva ESP32 Universal Core Board
    • Designed by Jhonatan Córdoba Rodríguez
    • Version 1.0
    • www.iaactiva.com
MCU
  • ESP32-WROOM-32 centered on PCB.
  • Antenna end requires no copper, traces, fills, vias, or components below/near the antenna.
  • Maintain at least 15 mm antenna clearance.
  • EN/reset and GPIO0/boot programming circuitry included.
Power Architecture
  • VIN input pad feeds TLV1117LV33 3.3 V regulator.
  • BAT+ and BAT- pads provided for external battery wiring.
  • 3V3 rail powers ESP32 and expansion pads.
  • Power LED connected to 3V3 through a current-limiting resistor.
  • Status LED connected through an open solder jumper for optional GPIO2 default routing.
  • Distributed GND pads around PCB.
Programming Interface
UART programming header/pads expose:
  • 3V3
  • GND
  • TX0 / GPIO1
  • RX0 / GPIO3
  • EN
  • GPIO0
GPIO Access
All requested ESP32 GPIOs are exposed on large solder pads and labeled: GPIO0, GPIO1, GPIO2, GPIO3, GPIO4, GPIO5, GPIO12, GPIO13, GPIO14, GPIO15, GPIO16, GPIO17, GPIO18, GPIO19, GPIO21, GPIO22, GPIO23, GPIO25, GPIO26, GPIO27, GPIO32, GPIO33, GPIO34, GPIO35, GPIO36, GPIO39.
Display Interfaces
Universal TFT SPI solder interface:
  • 3V3, GND, SCK=GPIO18, MOSI=GPIO23, MISO=GPIO19, CS=GPIO5, DC=GPIO21, RST=GPIO22, BL=GPIO4
Universal OLED 0.96 I2C solder interface:
  • 3V3, GND, SDA=GPIO21, SCL=GPIO22
Layout Intent
  • ESP32 centered with antenna keepout oriented toward a clear edge/region.
  • GPIO solder pads distributed around all board edges.
  • Keep signal routing short and symmetric where practical.
  • Preserve free expansion space for user wiring.
  • SPI display signals should use short, direct routes and avoid unnecessary vias.
Validation Criteria
  • ERC clean except intentional exposed pads/solder-jumper single-pin warnings if accepted.
  • DRC clean after routing.
  • No remaining airwires after routing.
  • Antenna keepout contains no copper, fills, traces, vias, or components.
  • Overview

  • Board Requirements

  • MCU

  • Power Architecture

  • Programming Interface

  • GPIO Access

  • Display Interfaces

  • Layout Intent

  • Validation Criteria