• Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
  • Ground
    A common return path for electric current. Commonly known as ground.
  • Net Portal
    A net identifier used to create connectivity to other Net Portal with the same designator. #portal
  • Power Net Portal
    Power net portal is a special schematic object used to define a power or ground net. Power ports allow you to conveniently indicate a power net at any location in the design. Power nets of the same designator automatically connect throughout your design #portal #power
  • Generic Resistor
    A generic fixed resistor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0Ω 10Ω 100Ω 1.0kΩ 10kΩ 100kΩ 1.0MΩ 1.1Ω 11Ω 110Ω 1.1kΩ 11kΩ 110kΩ 1.1MΩ 1.2Ω 12Ω 120Ω 1.2kΩ 12kΩ 120kΩ 1.2MΩ 1.3Ω 13Ω 130Ω 1.3kΩ 13kΩ 130kΩ 1.3MΩ 1.5Ω 15Ω 150Ω 1.5kΩ 15kΩ 150kΩ 1.5MΩ 1.6Ω 16Ω 160Ω 1.6kΩ 16kΩ 160kΩ 1.6MΩ 1.8Ω 18Ω 180Ω 1.8KΩ 18kΩ 180kΩ 1.8MΩ 2.0Ω 20Ω 200Ω 2.0kΩ 20kΩ 200kΩ 2.0MΩ 2.2Ω 22Ω 220Ω 2.2kΩ 22kΩ 220kΩ 2.2MΩ 2.4Ω 24Ω 240Ω 2.4kΩ 24kΩ 240kΩ 2.4MΩ 2.7Ω 27Ω 270Ω 2.7kΩ 27kΩ 270kΩ 2.7MΩ 3.0Ω 30Ω 300Ω 3.0KΩ 30KΩ 300KΩ 3.0MΩ 3.3Ω 33Ω 330Ω 3.3kΩ 33kΩ 330kΩ 3.3MΩ 3.6Ω 36Ω 360Ω 3.6kΩ 36kΩ 360kΩ 3.6MΩ 3.9Ω 39Ω 390Ω 3.9kΩ 39kΩ 390kΩ 3.9MΩ 4.3Ω 43Ω 430Ω 4.3kΩ 43KΩ 430KΩ 4.3MΩ 4.7Ω 47Ω 470Ω 4.7kΩ 47kΩ 470kΩ 4.7MΩ 5.1Ω 51Ω 510Ω 5.1kΩ 51kΩ 510kΩ 5.1MΩ 5.6Ω 56Ω 560Ω 5.6kΩ 56kΩ 560kΩ 5.6MΩ 6.2Ω 62Ω 620Ω 6.2kΩ 62KΩ 620KΩ 6.2MΩ 6.8Ω 68Ω 680Ω 6.8kΩ 68kΩ 680kΩ 6.8MΩ 7.5Ω 75Ω 750Ω 7.5kΩ 75kΩ 750kΩ 7.5MΩ 8.2Ω 82Ω 820Ω 8.2kΩ 82kΩ 820kΩ 8.2MΩ 9.1Ω 91Ω 910Ω 9.1kΩ 91kΩ 910kΩ 9.1MΩ #generics #CommonPartsLibrary
  • Generic Capacitor
    A generic fixed capacitor for rapid developing circuit topology. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF 10pF 100pF 1000pF 0.01uF 0.1uF 1.0uF 10uF 100uF 1000uF 10,000uF 1.1pF 11pF 110pF 1100pF 1.2pF 12pF 120pF 1200pF 1.3pF 13pF 130pF 1300pF 1.5pF 15pF 150pF 1500pF 0.015uF 0.15uF 1.5uF 15uF 150uF 1500uF 1.6pF 16pF 160pF 1600pF 1.8pF 18pF 180pF 1800pF 2.0pF 20pF 200pF 2000pF 2.2pF 22pF 20pF 2200pF 0.022uF 0.22uF 2.2uF 22uF 220uF 2200uF 2.4pF 24pF 240pF 2400pF 2.7pF 27pF 270pF 2700pF 3.0pF 30pF 300pF 3000pF 3.3pF 33pF 330pF 3300pF 0.033uF 0.33uF 3.3uF 33uF 330uF 3300uF 3.6pF 36pF 360pF 3600pF 3.9pF 39pF 390pF 3900pF 4.3pF 43pF 430pF 4300pF 4.7pF 47pF 470pF 4700pF 0.047uF 0.47uF 4.7uF 47uF 470uF 4700uF 5.1pF 51pF 510pF 5100pF 5.6pF 56pF 560pF 5600pF 6.2pF 62pF 620pF 6200pF 6.8pF 68pF 680pF 6800pF 0.068uF 0.68uF 6.8uF 68uF 680uF 6800uF 7.5pF 75pF 750pF 7500pF 8.2pF 82pF 820pF 8200pF 9.1pF 91pF 910pF 9100pF #generics #CommonPartsLibrary
  • Generic Inductor
    A generic fixed inductor for rapid developing circuit topology. *You can now change the footprint and 3D model at the top level anytime you want. This is the power of #generics
  • RMCF0805JT47K0
    47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film #forLedBlink
  • 875105359001
    10uF Capacitor Aluminum Polymer 20% 16V SMD 5x5.3mm #forLedBlink #commonpartslibrary #capacitor #aluminumpolymer #radialcan
  • CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric) #forLedBlink
SVN
GPIO25
SVP
GND
GPIO22
GPIO17
GPIO27
GPIO26
GPIO12
GND
3.3V
GPIO37
5V
3.3V
GND
GPIO2
GPIO33
GND
GPIO13
GPIO32
GND
GPIO38
GPIO15
GPIO21

TTGO T DISPLAY

TTGO T DISPLAY
Description

Created
June 28th 2023
Last updated by vasyl
2 years ago
1 Contributor(s)
vasyl

Controls

Properties

Part Type
RF Board
Manufacturer Name
TTGO
Manufacturer Part Number
TTGO T DISPLAY
Designator Prefix
U

Availability & Pricing

No results found.

Assets

Simulation

µs

Simulation Speed

CAN YOU CHANGE THE TTGo pins?
CAN YOU CHANGE THE TTGo pins?
3mo
DISEÑAME UNA PLACA CVOMMPATIBLE CON EL ESP32 TFT
DISEÑAME UNA PLACA CVOMMPATIBLE CON EL ESP32 TFT
4mo
quiero un circuito que incluya el TTGO v2 y el modulo ACS712
@copilot quiero un circuito que incluya el TTGO v2 y el modulo ACS712
1y
Entiendo que quiere diseñar un circuito que relate la placa del controlador TTGO T-Display ESP32 con el módulo ACS712 para medir la corriente. El módulo ACS712 se utiliza a menudo en aplicaciones de AC o de corriente continua para detectar y medir corriente. Vamos a preparar un diagrama de conexiones para usted.
Tenga en cuenta que el módulo ACS712 tiene tres pines que son Vcc, GND y OUT. Normalmente, Vcc se conecta a una fuente de alimentación de 5V, GND a tierra y OUT a un puerto analógico para leer las mediciones. Sin embargo, el ESP32 es un microcontrolador de 3.3V, no de 5V, así que necesitará un divisor de voltaje en el pin de salida del ACS712 para adecuar los niveles de voltaje. Asumo que tiene un divisor de voltaje disponible.
Aquí están las conexiones propuestas:
  1. Conectar ACS712:Vcc al TTGO:5V
  2. Conectar ACS712:GND a una de las TTGO:GND
  3. Conectar AWS712:OUT con un divisor de voltaje, y luego conectar el divisor de voltaje a TTGO:GPIO33 (este último es un puerto de entrada analógica)
Circuitos de la siguiente forma:
  • ACS712: Vcc -> TTGO: 5V
  • ACS712: GND -> TTGO: GND
  • Divide resistor network: ACS712:OUT -> TTGO:GPIO33
Recuerde que puede necesitar ajustar estos pasos según las especificaciones exactas de su configuración y los valores que está midiendo con el módulo ACS712.
También es importante que comprenda que el TTGO T-Display ESP32 tiene un regulador de voltaje incorporado, así que debería ser capaz de manejar los 5V que necesita el módulo ACS712, pero siempre es una buena idea verificar las especificaciones del hardware que está utilizando.
Finalmente, tenga en cuenta que los pines GPIO de los dispositivos ESP32 son tolerantes a 3.3V, por lo que se debe utilizar un divisor de voltaje en la salida del ACS712 para garantizar que el nivel de voltaje esté dentro de los límites aceptables para el ESP32. Como no tengo detalles específicos sobre su divisor de voltaje, debo asumir que ya está configurado correctamente para esta aplicación.
Espero que estas instrucciones de conexión le sean útiles. Si tiene alguna otra pregunta o necesita más ayuda, no dude en preguntar.
1y
@copilot implementa el circuito
1y
Lo siento por cualquier confusión, pero como asistente de inteligencia artificial, no tengo la capacidad de implementar físicamente el circuito. Sin embargo, puedo orientarlo en cómo construir el circuito en el software basado en navegador Flux. Siga los siguientes pasos:
  1. Abra su proyecto en Flux.
  2. Agregue el componente TTGO T-Display ESP32 a su área de trabajo en el proyecto.
  3. Agregue el módulo ACS712 a su área de trabajo en el proyecto.
  4. Conecte los pines como se indicó anteriormente. En otras palabras:
    • Conecte ACS712:Vcc al TTGO:5V
    • Conecte ACS712:GND a una de las lugares TTGO:GND
    • Conecte ACS712:OUT a un divisor de voltaje, y luego conecte la salida del divisor de voltaje a TTGO:GPIO33
  5. Guarde y verifique su circuito.
Por favor tenga en cuenta que su circuito real podría variar dependiendo de las características específicas de su proyecto. Le recomendaría que hiciera una simulación de su circuito antes de implementarlo.
1y
@copilot realiza el circuito
1y
Lamento si hubo alguna confusión, pero como una inteligencia artificial, no tengo la capacidad de realizar manipulaciones físicas, lo que incluye construir circuitos en una plataforma como Flux.ai. Sin embargo, le proporcioné los pasos arriba para configurar el circuito en su computadora. Le sugiero que siga los pasos que proporcioné anteriormente en Flux.ai.
Si necesita más asistencia para construir el circuito, no dude en preguntar. Estoy aquí para proporcionarle instrucciones y ayudarlo a entender cómo se deben conectar los componentes.
1y
@copilot muestrame el circuito en pantalla
1y
Lamento cualquier confusión. Como un asistente AI, no tengo la capacidad de crear gráficos, imágenes o interfaces visuales. Mi función principal es proporcionar información y asistencia basada en texto. Sin embargo, puedo brindar instrucciones paso a paso sobre cómo podría configurar su circuito en Flux.
  1. Inicie Flux.ai e importe los componentes que necesita (en este caso, TTGO T-Display ESP32 y ACS712).
  2. Coloque estos componentes en su espacio de trabajo.
  3. Ahora es el momento de hacer las conexiones según las instrucciones anteriores:
    • Conecte ACS712:Vcc al TTGO:5V.
    • Conecte ACS712:GND a una de las patillas GND del TTGO.
    • Conecte ACS712:OUT a un divisor de voltaje y luego la salida de este divisor al GPIO33 del TTGO.
  4. Una vez que haya hecho estas conexiones, debería poder ver el diagrama completo en su pantalla.
Recuerde, la visualización exacta del circuito puede variar dependiendo de su software y configuración específicos. Si necesita ayuda adicional para entender la disposición de los componentes y las conexiones, no dude en solicitarlo.
1y
how do i connect lilygo ttgo gpio pins to use esp wifi firmware on flipperzero\_...
@copilot how do i connect lilygo ttgo gpio pins to use esp wifi firmware on flipperzero_connectors
1y
In your case, you want to connect two ESP32 controllers of the TTGO T-Display model together using UART serial communication. Below are the steps you could follow:
  1. Choose the GPIO pins for your UART connection on both ESP32 modules. From the ESP32 pinout, you could choose any general-purpose I/O pins for UART communication, but it's recommended to use those preconfigured for UART interfaces.
    For example, for ESP32_1 you could use GPIO1 as TX and GPIO3 as RX for UART0. For ESP32_2, you may choose another UART interface like UART2 and use GPIO16 as RX and GPIO17 as TX.
  2. Now, make the connections between your two ESP32s. Connect TX pin on ESP32_1 to RX pin on ESP32_2, and RX pin on ESP32_1 to TX pin on ESP32_2.

    Table


    ESP32_1ESP32_2
    GPIO1 (TX)GPIO16 (RX)
    GPIO3 (RX)GPIO17 (TX)
  3. Don't forget to connect the ground (GND) of both the ESP32s together. This is to ensure that they have a common point of reference for the signal voltages.
  4. Once the connection is made, you can use the ESP32's UART peripheral to send and receive data between both ESP32s. You'll need to write a firmware that configures the chosen GPIOs for UART communication on both ESP32s. Leverage the Arduino HardwareSerial library, which allows you to use serial communication on the ESP32's UART interfaces.
Please keep in mind that these steps provide a general way of establishing UART communication, and you might need to adjust them to your specific use case or board design. Also, be aware of the voltage rating of your ESP32s, ensure not to accidentally provide a voltage above their tolerable limit.
Source(s):
1y
help me to conect two esp32 with uart
@copilot help me to conect two esp32 with uart
1y
Absolutely, to connect two ESP32 microcontrollers using UART, follow these steps:
  1. Choose one ESP32 board to be the transmitter and the other to be the receiver.
  2. Identify the UART pins for each ESP32 board. The ESP32 usually has three UART interfaces:
    • UART0: RX0 on GPIO 3, TX0 on GPIO 1
    • UART1: RX1 on GPIO 9, TX1 on GPIO 10
    • UART2: RX2 on GPIO 16, TX2 on GPIO 17
  3. Connect the Tx pin of the transmitter ESP32 to the Rx pin of the receiver ESP32.
  4. Connect the Rx pin of the transmitter ESP32 to the Tx pin of the receiver ESP32.
  5. Connect both ESP32 GND pins together.
Note: Double-check your microcontroller's datasheet to verify the pinout, as there can be variations between different ESP32 models.
Once the physical connection is established, you'll need to write a UART communication code for both the transmitter and receiver ESP32 boards.
Source(s):
1y
Hey, I’m Copilot, your AI design assistant. I can help you brainstorm ideas, deb...
Hey, I’m Copilot, your AI design assistant. I can help you brainstorm ideas, debug problems, research components, and even make wiring connections for you. Ask me questions like:
  • @copilot I'm designing a PCB for a medical device that measures heart rate and temperature. Can you give me the list of components I will need?
  • @copilot How would I connect these parts to make the LED flash at 1kHz?
  • @copilot can you choose 4 digital pins on the ATMega328P-AU that I have here to use as GPIO given that I am already using some pins for reset, the external clock, UART, and I2C.
Chat with me by tagging @copilot on comments or in the chat.
1y
Someone is typing...
Checks that the power traveling across a given resistor is under its rating with 50% headroom.
Learn more
Checks that IC pins that require pull up or pull down resistors have them.
Learn more
Checks that capacitors have appropriate voltage ratings to prevent overheating and ensure reliable circuit operation.
Checks that all parts have a part number and are available from distributors.
Reports copper elements that are shorting.
Reports parts that have no footprint.
Reports nodes that are assigned to a layer that doesn't exist in the layout stackup.
Reports components that have been modified using the "!important" flag.
Reports terminals that are not connected properly. NOTE: Only connections to the center of pads are considered valid.
Reports nodes that are using rules that are not supported anymore.
Reports layers that have multiple copper fills of different nets. Make sure the Connected Layers rule value of nets with fills is valid.
Detect any via, trace or copper fill island that is not connected to any net.