I verified the bare microphone’s nine-pin pinout and I²S wiring, which differ from a six-pin breakout module. I also found conflicting lifecycle information; the guide will flag that sourcing risk and clearly distinguish functional alternatives from drop-in replacements.
The INMP441 from InvenSense (TDK) is an omnidirectional, bottom-port MEMS microphone integrating signal conditioning, an ADC, anti-aliasing filters, power management, and a 24-bit I²S digital output. It connects directly to a microcontroller or DSP for near-field voice and audio capture without an external audio codec.
Scope: This guide covers the bare nine-terminal microphone, not the six-terminal breakout module commonly sold as “INMP441.” Breakout header numbering, onboard passives, and CHIPEN strapping are module-specific; inspect the module schematic before applying the bare-device pin n...
Created the cited INMP441 Application and Usage Guide in the project files, covering all seven requested sections and authoritative sources.
It distinguishes the nine-pin microphone from six-pin breakout modules, explains I²S integration, and flags conflicting lifecycle information; current stock, pad pitch, and drop-in replacement compatibility remain unverified.
The INMP441 from InvenSense (TDK) is an omnidirectional, bottom-port MEMS microphone integrating signal conditioning, an ADC, anti-aliasing filters, power management, and a 24-bit I²S digital output. It connects directly to a microcontroller or DSP for near-field voice and audio capture without an external audio codec.
Scope: This guide covers the bare nine-terminal microphone, not the six-terminal breakout module commonly sold as “INMP441.” Breakout header numbering, onboard passives, and CHIPEN strapping are module-specific; inspect the module schematic before applying the bare-device pin numbers below. The manufacturer specifies a nine-terminal LGA_CAV package.
1. Quick Specifications
Absolute maximum ratings are stress limits, not normal design targets. Use a regulated 1.8 V or 3.3 V supply as the practical integration choice, with tolerance and transients kept within the electrical-characteristics range.
Table
Parameter
Classification
Specification / conditions
Supply voltage
Operating range, Table 1
1.62–3.63 V. Pin-description nominal supplies are 1.8–3.3 V.
Supply voltage
Absolute maximum, Table 4
−0.3 to +3.63 V. No positive transient margin exists above the stated operating upper endpoint.
Digital input voltage
Absolute maximum
−0.3 V to the lower of VDD + 0.3 V and 3.63 V; not 5 V tolerant.
Normal supply current
Typical / maximum
At VDD = 1.8 V: 1.4 / 1.6 mA; at VDD = 3.3 V: 2.2 / 2.5 mA.
Standby current
Maximum
0.8 mA at the stated 1.8 V and 3.3 V conditions.
Power-down current
Maximum
2 µA at 1.8 V; 4.5 µA at 3.3 V.
Operating temperature
Operating range
−40 to +85 °C.
Storage temperature
Non-operating rating
−55 to +150 °C.
SCK / bit clock
Operating timing limits
0.5–3.2 MHz.
WS / sample frequency
Operating timing limits
7.8–50 kHz; also obey 64 SCK cycles per stereo frame.
Output format
Interface
24-bit signed two’s-complement I²S, MSB first, carried in 32-clock channel slots.
Package
Mechanical
Nine-terminal LGA_CAV; nominal body 4.72 × 3.76 × 1.00 mm.
Pad pitch
Verification limitation
A numeric pitch could not be verified reliably from the retrieved drawing. Use the complete manufacturer land pattern and outline, Figures 14 and 16; do not substitute a generic LGA footprint.
2. Pinout & Connections
Pin assignments and required SD pulldown come from Table 6.
Table
Pin Number
Pin Name
Description
Best Practice
1
SCK
I²S serial-data clock input
Connect to host BCLK/SCK output. The host is clock master.
2
SD
Serial-data output; high impedance outside the selected channel
Connect to host I²S receive-data input; fit a 100 kΩ pulldown to GND on the shared data trace.
3
WS
Word-select input
Connect to host WS/LRCLK output; provide a full stereo frame even with one microphone.
4
L/R
Channel selection
Tie to GND for left or VDD for right; do not leave floating.
5
GND
Ground
Connect to PCB ground.
6
GND
Ground adjacent to supply
Connect to PCB ground; use as the local decoupling return.
7
VDD
Power supply
Connect to regulated supply; place 0.1 µF ceramic from pin 7 to pin 6.
8
CHIPEN
Enable; low disables, high enables
Tie to VDD for always-on operation, or drive from a supply-compatible GPIO with a defined state.
9
GND
Ground
Connect to PCB ground.
All nine pin functions and table connection requirements are supported by Table 6. Keeping control inputs defined is integration guidance, not a claim that a particular external pull-resistor value is mandated.
For L/R, WS, and SCK, guaranteed input-high starts at 0.7 × VDD and input-low extends to 0.25 × VDD. Check the host’s I/O voltage domain; a 3.3 V clock must not directly drive a microphone powered at 1.8 V because of the input absolute maximum.
3. Standard Application Circuit
Single-microphone, 3.3 V I²S connection
Connect VDD (7) to regulated 3.3 V and all GND terminals (5, 6, 9) to ground. Tie CHIPEN (8) to VDD and L/R (4) to GND to enable the left channel.
Fit 0.1 µF X7R or better ceramic decoupling between VDD and GND, immediately beside the microphone. This is the manufacturer’s decoupling recommendation, not a generic 1 µF substitution.
Connect host BCLK to SCK (1), host LRCLK to WS (3), and SD (2) to the host’s I²S receive input. Fit 100 kΩ from SD to GND to discharge the bus when outputs are tri-stated. These are not I²C signals and do not require I²C pull-ups.
Configure the receiver for standard I²S, 24-bit signed data in two 32-bit slots, MSB first, with the MSB delayed one clock after the WS transition. Keep 64 bit clocks per frame, including in mono applications.
Worked clock configuration: At a chosen 48 kHz sample rate, BCLK = 64 × 48,000 = 3.072 MHz. This derived value is inside the 0.5–3.2 MHz SCK range, and 48 kHz is inside the WS range.
Startup: Expect zero output for the first 2^18 SCK cycles following power-up: the datasheet gives 85 ms at 3.072 MHz. Continue generating clocks and discard this interval before diagnosing a silent microphone.
Two microphones on one I²S input
Use the same SCK and WS for both microphones; assign opposite L/R states and connect their SD outputs to the shared receive-data line. The inactive channel is tri-stated, allowing the two selected channels to share the bus; retain the SD pulldown and give each microphone its own local decoupling capacitor.
Firmware integration advice: extract the selected channel, preserve the sign of the 24-bit sample, and check how the host peripheral aligns those bits in a 32-bit DMA word. That alignment is host-specific, not a microphone register setting. No LED resistor, USB CC network, analog preamplifier, or external audio ADC is part of this circuit.
4. PCB Layout & Routing Guidelines
Use the exact bottom-port footprint. The manufacturer specifies a 1:1 land-pattern relationship to the package solder pads. Align the PCB sound opening to the microphone acoustic port; keep solder, paste, and enclosure obstructions out of the acoustic path. Use Figures 14 and 16 for final geometry rather than the outline dimensions alone.
Minimize the decoupling loop. Place the 0.1 µF capacitor as close to VDD as possible; make both connections short, on one layer, without vias in those connections. Put thermal ground-plane connections on the capacitor’s far side so the local capacitor-to-microphone return remains short.
Route I²S as single-ended digital signals. SCK, WS, and SD are not differential pairs. Engineering practice: keep clock routes short over a continuous ground reference, avoid long stubs and switching-power aggressors, and validate edge quality on long or off-board connections. No universal trace-length or series-termination value was verified for this application.
Size copper for the actual load. This is a milliampere-load microphone, not a high-current device: normal-mode maximum at 3.3 V is 2.5 mA. Use fabrication-compatible traces and prioritize return paths and decoupling rather than power-width rules intended for motors or regulators.
Protect the acoustic port during assembly. Keep wash water out of the port; do not use blow-off procedures or ultrasonic cleaning. State these restrictions in assembly notes.
5. Common Pitfalls / Things to Watch Out For
Treating a six-pin breakout as the bare microphone, or applying 5 V. The bare part has nine terminals, including CHIPEN and three grounds; breakout modules may hide those connections. A 5 V supply or digital input violates the bare-device limits. Check the actual module schematic and voltage domain before wiring.
Using the wrong audio framing or reading too soon. A 24-bit payload does not mean a 24-clock channel slot: use 32 clocks per channel, 64 per frame, correct L/R selection, and the I²S one-clock MSB delay. Wait through the documented startup-zero interval before calling the device faulty.
6. Popular Alternatives & Equivalents
No verified cross-manufacturer drop-in replacement was established. The following are functional migration candidates, not approved substitutions; qualification must include supply range, digital timing, sensitivity, acoustic opening, and assembly process. Current stock was not verified.
Table
Candidate
Compatibility
Required changes / evidence
Knowles SPH0645LM4H-B
Functionally similar I²S; not pin-compatible or footprint-compatible
Six pins rather than nine; body 3.50 × 2.65 × 0.98 mm. Uses a 24-bit I²S format with 18-bit data precision and 64 clocks/frame. Redesign the footprint and pin mapping, then validate receiver timing and sample handling.
Functionally similar audio sensor only; not pin-compatible, footprint-compatible, or I²S-compatible
Five-pin PDM microphone. Requires a PDM-capable host/decimation path and a new PCB footprint; cannot be substituted into an unchanged I²S circuit. Infineon currently labels this part “not for new design”; it is a legacy redesign candidate, not a long-term sourcing recommendation. Manufacturer product page.
The Flux library search returned a Knowles SPH0645LM4H family entry, but not a confirmed exact SPH0645LM4H-B entry. Do not assume the family entry’s symbol or footprint establishes suffix-specific compatibility. Neither candidate above is a verified drop-in.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
Start with established distributors such as DigiKey, Mouser, and Farnell for a traceable quotation. DigiKey and Farnell host manufacturer documents used here; this does not confirm present stock or authorization for every exact order code. No current purchasable inventory was verified.
Packaging Options
Manufacturer ordering guide: INMP441ACEZ-R0 uses a 13-inch tape-and-reel; INMP441ACEZ-R7 uses a 7-inch tape-and-reel. The historical guide already flags the 7-inch option for discontinuation. Distributor cut-tape or custom-reel availability must be confirmed separately.
Standard MOQ
Verified historical full-reel quantities: 4,500 for R0, 1,000 for R7. Reel quantity is not necessarily purchase MOQ. A current one-unit cut-tape MOQ was not verified; request the distributor’s actual MOQ and packaging multiple.
Lifecycle / Availability
InvenSense PCN-000172, dated March 15, 2018, names INMP441ACEZ-R0, INMP441ACEZ-R7, and INMP441WACEZ-R7 for EOL, with last-time buy September 15, 2018 and last-time ship March 15, 2019. Manufacturer EOL notice hosted by DigiKey. The generic TDK INMP441 page still shows “Production (NRND),” creating a lifecycle discrepancy that must be resolved for the exact order code before procurement. TDK product page.
Sourcing Advice
Prefer manufacturer-confirmed franchised channels and traceable lots. Require the exact ordering suffix, lot/date code, packaging condition, and applicable lifecycle notice. Marketplace modules labeled “INMP441” are not evidence of genuine bare-device stock; avoid untraceable or reclaimed material. For production, qualify a currently supported microphone and redesign rather than relying on speculative legacy stock.
Verification limitations: Numeric pad pitch was not reliably established; exact alternative availability, present pricing, cut-tape MOQ, and exact-order-code lifecycle reconciliation remain open. The EOL notice was verified through direct web extraction of the primary manufacturer notice; its separate immutable datasheet-citation lookup remained pending. No schematic, symbol, or footprint was changed by this guide.
Sources
InvenSense INMP441 manufacturer datasheet, DS-INMP441-00, revision 1.0, February 6, 2014:Farnell-hosted PDF used for the verified technical citations. Sections: Tables 1–4 and 6; Startup; I²S Data Interface; Power-Supply Decoupling; PCB Design and Land Pattern Layout; Board Wash; Outline Dimensions; Ordering Guide.
Manufacturer datasheet link:TDK/InvenSense INMP441 PDF. DigiKey’s manufacturer-datasheet presentation identifies revision 1.1, May 21, 2014. The numerical claims in this guide are cited to the retrieved revision 1.0; the newer revision was not separately extracted for a line-by-line comparison.
Knowles SPH0645LM4H-B datasheet:Manufacturer-authored PDF hosted by DigiKey; exact revision/date of the extracted copy was not independently confirmed. Interface and mechanical/pin tables support the functional-alternative assessment.
Infineon IM69D130 datasheet, revision 1.0, December 19, 2017:Manufacturer PDF; Table 7 supports the PDM interface and five-pin mapping. Manufacturer product page provides the current not-for-new-design warning.