I’ll write the application and usage guide for CP2102N-A02-GQFN20, verifying the pinout, application circuit, alternatives, and purchasing details against primary sources, then save it in the project files.
I’ve verified the 20-pin pinout and reference circuit; two important points are the required VBUS sense divider and the absence of a separate I/O-voltage supply. I’m checking replacement compatibility and packaging details before finishing the cited guide.
The Silicon Labs CP2102N-A02-GQFN20 is a USB 2.0 full-speed USB-to-UART bridge with an integrated USB transceiver and clock, supporting UART rates from 300 baud to 3 Mbaud. Its most common use is adding a computer-accessible serial port to a microcontroller-based product for configuration, diagnostics, or a UART-based programming interface.
Scope: This guide applies specifically to the A02, QFN20 variant, not the QFN24/QFN28 pinouts or the older CP2102. Manufacturer requirements are cited inline; additional implementation recommendations and illustrative calculations are identifie...
Created and checked the CP2102N-A02-GQFN20 Application and Usage Guide in the project files, covering all seven requested sections with citations and source links. It includes the full pinout, reference wiring, LED calculations, USB-C guidance, layout recommendations, and two functional alternatives—neither claimed as a drop-in replacement. Unverified sourcing details and incomplete source checks are explicitly flagged; the schematic and PCB were unchanged.
The Silicon Labs CP2102N-A02-GQFN20 is a USB 2.0 full-speed USB-to-UART bridge with an integrated USB transceiver and clock, supporting UART rates from 300 baud to 3 Mbaud. Its most common use is adding a computer-accessible serial port to a microcontroller-based product for configuration, diagnostics, or a UART-based programming interface.
Scope: This guide applies specifically to the A02, QFN20 variant, not the QFN24/QFN28 pinouts or the older CP2102. Manufacturer requirements are cited inline; additional implementation recommendations and illustrative calculations are identified separately. Research date: October 7, 2026. This document does not certify the existing Flux symbol, footprint, or a completed PCB.
1. Quick Specifications
Absolute maximum ratings are stress limits, not acceptable operating targets. Operating the device at these limits is not implied by the datasheet.
Use a nominal 3.3 V rail; never apply USB 5 V to VDD.
VREGIN supply
3.0–5.25 V.
GND − 0.3 V to 5.8 V.
The upper end of this range is appropriate for nominal USB 5 V operation; low input voltage does not guarantee a regulated 3.3 V output.
I/O supply domain
No separate VIO pin on QFN20; VIO = VDD.
Do not interpret the family's separate-VIO ratings as an available QFN20 feature.
Use level translation for a 1.8 V MCU.
USB D+ / D− voltage
USB full-speed interface, 12 Mbps.
GND − 0.3 V to VDD + 0.3 V.
These are not 5 V digital inputs.
UART, GPIO, VBUS, RSTb and other non-power/non-USB pins
Check the receiving interface's thresholds and power sequencing.
GND − 0.3 V to 5.8 V when VIO > 3.3 V; GND − 0.3 V to VIO + 2.5 V when VIO < 3.3 V, as written in the datasheet.
These conditional stress limits are not an unconditional claim of 5 V tolerance, especially while unpowered. The table does not explicitly resolve the boundary at VIO = 3.3 V; do not invent a boundary rating.
Active supply current
9.5 mA typical at 115200 baud; 13.7 mA typical at 3 Mbaud, continuous bidirectional transfer.
QFN20 with ground center pad; nominal 3 mm body dimension, 0.50 mm land-pattern pitch; 0.75 mm typical package height, 0.80 mm maximum.
—
Use the manufacturer's QFN20 drawing and land pattern, not an arbitrary 20-pin QFN footprint.
2. Pinout & Connections
Pin numbering below follows Section 5.3, CP2102N QFN20 Pin Definitions, including the center ground pad. Pins 1–5 are documented in the first portion of the pin table; pins 6–20 and the center pad are in its continuation.
The pin functions in this table are manufacturer-defined. Connection advice is engineering guidance except where a specific manufacturer requirement is cited.
Table
Pin Number
Pin Name
Description
Best Practice
1
GPIO.1 / RS485
GPIO or RS-485 control output.
Connect to a separate RS-485 transceiver's enable input only after configuring the alternate function. This pin is not an RS-485 bus driver. Leave unconnected if unused.
2
GPIO.0 / CLK
GPIO or clock output.
Configure before using as a clock source; leave unconnected if unused.
3
GND
Ground.
Connect directly to the ground plane.
4
D+
USB data positive.
Connect to connector D+ through the selected USB-compatible ESD protection path.
5
D−
USB data negative.
Connect to connector D−; route with D+.
6
VDD
Device supply input or internal regulator output.
Bus-powered: bypass with 4.7 µF + 100 nF to GND. Never connect to 5 V.
7
VREGIN
Internal regulator input.
Bus-powered: connect to nominal USB 5 V and bypass with 4.7 µF + 100 nF. If bypassing the regulator, tie VREGIN to VDD.
8
VBUS
USB bus-presence sense input.
Use USB VBUS → 22.1 kΩ → pin 8, with 47.5 kΩ from pin 8 to GND. Do not confuse this node with the VREGIN power net.
9
RSTb
Active-low reset.
Add the recommended 1 kΩ pull-up to VDD. If externally controlled, use an open-drain reset driver rather than actively forcing the line high.
10
NC
No connect.
Leave floating, as specified; do not tie to GND.
11
SUSPENDb
Output low during USB suspend.
Route to external power-management logic if needed; otherwise leave unconnected. Do not tie an output to a supply rail.
12
GND
Ground.
Connect to the same ground plane as pin 3 and the center pad.
13
WAKEUP
Active-low remote-wakeup input.
If unused, recommend an external 10 kΩ pull-up to VDD to establish an inactive level. This resistor is a design recommendation, not a verified manufacturer-required unused-pin value.
14
SUSPEND
Output high during USB suspend.
Use for suspend-aware load control if required; otherwise leave unconnected.
15
CTS
Active-low clear-to-send input.
With flow control, connect to MCU RTS. Without it, disable hardware flow control on the host; a recommended 10 kΩ pull-down to GND establishes an asserted CTS state. The resistor is not a verified manufacturer-required termination.
16
RTS
Active-low handshake output.
With flow control, connect to MCU CTS and enable host hardware flow control; otherwise leave unconnected.
17
RXD
UART receive input.
Connect to MCU TX. If no transmitter is attached, recommend a pull-up to VDD to establish UART idle-high.
18
TXD
UART transmit output.
Connect to MCU RX, with level translation when required. Never connect directly to an RS-232 voltage-level input/output pair.
19
GPIO.3 / RXT
GPIO or receive-activity LED toggle.
Configure RXT before expecting activity indication; use a series-limited LED from VDD to this pin.
20
GPIO.2 / TXT
GPIO or transmit-activity LED toggle.
Configure TXT; use the same LED connection as RXT.
Center exposed pad
GND
Center ground connection.
Solder to the ground land and connect to ground copper; do not treat it as an optional mechanical-only pad. Check how the CAD library numbers this pad.
Variant-specific limitation: QFN20 has four GPIOs and no separate VIO or battery-charger-detect feature. The QFN20 pin table contains no dedicated DTR pin; do not copy a DTR-based automatic-reset circuit from a different CP210x package without redesigning the control interface.
3. Standard Application Circuit
USB bus-powered, 3.3 V UART interface
Use this setup for a conventional USB-to-MCU serial interface:
Power: Connect the USB connector's nominal 5 V supply to VREGIN, pin 7. Use the internal regulator's VDD, pin 6, as the bridge's nominal 3.3 V domain. The bus-powered topology is shown in Figure 2.1.
Decoupling: Fit 4.7 µF and 100 nF in parallel from VREGIN to GND, and another 4.7 µF and 100 nF in parallel from VDD to GND, following Figure 2.1. Place the 100 nF capacitors closest to their pins, followed by the 4.7 µF capacitors. Ceramic X7R parts are a practical choice; evaluate effective capacitance under DC bias rather than using nominal capacitance alone.
VBUS sensing: Connect 22.1 kΩ from connector VBUS to pin 8, and 47.5 kΩ from pin 8 to GND. A divider or functionally equivalent circuit is required for reliable operation; this remains important when USB power and the I/O domain ramp together. Engineering calculation at nominal 5 V: VSENSE = 5 × 47.5 / (22.1 + 47.5) = 3.412 V. This nominal arithmetic is not a complete tolerance or power-sequencing analysis.
Reset: Add 1 kΩ from RSTb to VDD. Provide a test point or an open-drain reset connection if useful for production test.
USB data: Connect connector D+ to pin 4 and D− to pin 5. Figure 2.5 includes external ESD protection. Use a USB-compatible protection device and its recommended layout; the example device is not a substitute for checking capacitance and clamping performance against the product's ESD target.
UART: Connect TXD, pin 18, to MCU RX; connect RXD, pin 17, to MCU TX; connect grounds. Optional flow-control wiring is RTS → MCU CTS and CTS ← MCU RTS, with the host configured accordingly. A 1.8 V transmitter may not reach the input-high threshold: the listed minimum is VIO − 0.6 V, including VBUS.
Unused pins: Leave NC floating; leave unused outputs and GPIOs unconnected, and establish suitable idle levels on disconnected inputs using the recommendations in Section 2. GPIOs default to input behavior with weak pull-ups/open-drain configuration; do not assume that statement proves an internal pull-up exists on dedicated CTS or WAKEUP.
No external crystal or USB pull-up/termination resistor is normally required: the clock, USB matching resistors, and USB pull-up are integrated. Do not copy external termination resistors from an unrelated USB MCU reference circuit.
External-regulator alternative: With an external 3.0–3.6 V supply, tie VREGIN to VDD as specified and keep the USB VBUS sense divider. Do not connect two independent regulators to the VDD node or backfeed USB VBUS from a self-powered board. The VBUS divider was restored in the self-powered diagram in datasheet Rev. 1.5 after it had accidentally been removed previously.
Optional UART activity LEDs: 3.3 V and 5 V calculations
TXT and RXT are high while idle and toggle during activity; the listed typical toggle rate is 20 Hz. For direct 3.3 V drive, connect VDD → resistor → LED anode, with the LED cathode at TXT or RXT, so the pin sinks current when low.
The following are illustrative engineering calculations, not verified specifications for a particular LED. Assume a red LED with VF = 2.0 V, target ILED = 2 mA, and initially neglect the driver voltage drop:
R = (VSUPPLY − VF − VDRIVER) / ILED
Table
LED supply
Ideal resistor calculation
Practical starting value
Connection limitation
3.3 V
(3.3 − 2.0) / 0.002 = 650 Ω
680 Ω gives about 1.91 mA with negligible driver drop.
Direct TXT/RXT sinking is suitable only after checking the actual pin configuration and LED current.
5 V
(5.0 − 2.0) / 0.002 = 1.5 kΩ
1.5 kΩ with a suitably rated external switch/buffer, or for an independent 5 V power LED.
Do not assume a 5 V-fed LED can be attached directly to a 3.3 V push-pull TXT/RXT output with guaranteed off-state behavior.
For the 3.3 V / 680 Ω example, using the specified VOL = 0.6 V bound gives approximately (3.3 − 2.0 − 0.6) / 680 = 1.03 mA; the datasheet specifies VOL at the drive-current conditions in Section 1. Use the selected LED's minimum forward voltage and the maximum supply voltage for a maximum-current check; include any external transistor's saturation voltage and preserve active-low polarity.
USB-C receptacle option
For a USB 2.0 device/sink receptacle, fit separate 5.1 kΩ pull-downs from CC1 to GND and from CC2 to GND; do not short the CC pins together. The fixed 5.1 kΩ Rd value is stated in Infineon's Type-C termination guidance, and the separate ground-connected sink terminations are supported by TI's CC guide.
Join the duplicate receptacle D+ contacts together and the duplicate D− contacts together close to the connector, then route the USB pair to the bridge; TI describes this connection in its HD3SS3220 UFP evaluation-module guide, Section 2.3. The CP2102N itself has no CC pins; these are connector-level additions. Rd resistors do not implement USB Power Delivery, do not raise the bridge's voltage ratings, and do not by themselves authorize arbitrary high-current loads.
Shielding recommendation: Bond the connector shell to chassis at the entry point when a conductive chassis is available. On a small plastic-enclosed board, provide a short local shell-to-ground connection or a configurable bonding network and select it through ESD/EMC testing; a universal RC/ferrite value for every enclosure cannot be verified. Never use the shell as a replacement for the USB signal-ground connection. General shield/return-path discussion is available in Silicon Labs AN0046; its indexed PDF cross-check remained pending during this research, so this paragraph is an engineering recommendation rather than a verified CP2102N-specific requirement.
A02 startup erratum: CP2102N_E110 permits an undefined D+/D− state during and immediately after power-on reset, typically about 15 ms. Test enumeration against the actual host, especially embedded hosts that depend on initial USB line state. For an affected host, follow the manufacturer's external forcing-circuit workaround; the errata describes using the RSTb rising edge to identify reset completion and a configured GPIO-controlled transistor to release the bus afterward. This workaround is conditional, not a mandatory addition to every ordinary PC-connected design.
4. PCB Layout & Routing Guidelines
The following are implementation recommendations, not a completed layout review. General USB geometry guidance is available in Silicon Labs AN0046; its indexed PDF verification was still pending, so the 90 Ω recommendation is not presented as an extracted CP2102N datasheet value.
Route D+/D− as a short differential pair targeting 90 Ω nominal. Maintain reasonably consistent coupling, an uninterrupted ground reference, minimal stubs, and as few layer changes as practical. Determine width and spacing from the actual fabricator's stackup—not a generic trace-width rule. Do not route over ground-plane splits.
Place ESD protection at the connector and decoupling at the IC. Keep the ESD discharge return short; place each 100 nF capacitor beside its supply pin with a nearby ground connection, and its 4.7 µF partner close behind. The two capacitor pairs are from the manufacturer's bus-powered circuit.
Ground and solder the exposed pad properly. Use the QFN20 manufacturer's land pattern, short low-impedance ground paths, and stencil/via treatment agreed with the assembler. Prefer a solid center-pad ground connection rather than narrow thermal-relief spokes that compromise the return path; control solder wicking if vias enter the land. Manufacturer guidance calls for NSMD pads and at least 60 µm solder-mask clearance around each pad. Reconcile this with the selected JLCPCB fabrication and assembly capabilities before release.
Size power traces for the total downstream load. The bridge is a low-current interface; there is no universal high-current trace width to prescribe. If VDD powers external circuitry, account for copper thickness, permitted temperature rise, voltage drop, and regulator dissipation. The regulator's 100 mA limit includes its own load. Engineering relation: PREG ≈ (VREGIN − VDD) × ITOTAL; a separate board thermal analysis is required when substantially loading it.
Keep the connector shield/ESD return local and verify the actual footprint. Ensure shell-bond currents do not take a long path through sensitive circuitry. Check pin-1 orientation, pad numbering, the center-ground land, solder-mask openings, and stencil design against the original package drawing—not merely the package name in a library listing.
5. Common Pitfalls / Things to Watch Out For
Treating VDD, VREGIN and VBUS as the same power node. VDD is the nominal 3.3 V domain; VREGIN accepts the USB-derived input supply; VBUS is a sense input requiring the divider or an equivalent circuit. Applying USB 5 V to VDD exceeds its 4.2 V stress ceiling, while omitting the VBUS divider violates the reliable-operation guidance. Keep those nets separately named and verify power-up, cable disconnect, and self-powered operation.
Copying another CP210x package's logic and control circuit. QFN20 has no independent VIO supply and no dedicated DTR pin in its pin table. A 1.8 V MCU interface requires translation, and a DTR-dependent automatic-programming circuit requires a different control solution. Also configure host RTS/CTS flow control to match the physical wiring; an unasserted CTS input can prevent the expected transmission when hardware flow control is enabled.
6. Popular Alternatives & Equivalents
No cross-manufacturer pin-compatible or footprint-compatible drop-in replacement was verified. The following are verified USB-to-UART alternatives for a redesign, not substitutes to populate on the existing CP2102N QFN20 land pattern.
FT231XQ provides USB full-speed to full-handshake UART, up to 3 Mbaud, in a 20-pin QFN, with 1.8–3.3 V I/O, according to the manufacturer's directly read product page.
Functionally similar only; not approved as pin- or footprint-compatible. Matching pin count is insufficient to establish compatibility.
Redesign supply/control wiring and the footprint; use the FTDI driver/configuration ecosystem. The current FT231X datasheet's indexed extraction remained pending, so a complete pin-by-pin and land-pattern comparison is not verified here.
USB-to-UART family supporting 300 baud–1 Mbaud and 3.0–5.5 V operation. The /MQ ordering code is 20-lead VQFN, with a 5 × 5 mm package.
Functionally similar only; not footprint-compatible. Its 5 × 5 mm package does not replace the CP2102N's nominal 3 mm package.
Redesign the PCB and supply/control circuit, add the required 12 MHz clock source, and accept the lower maximum UART rate. The clock accuracy requirement is ±0.25%, 2500 ppm maximum.
Both alternatives were found in the Flux parts library; that does not certify the quality or manufacturing readiness of those library assets. Recheck USB identifiers, host-driver distribution, UART polarity, flow control, clocking, power sequencing, and mechanical dimensions before approving a substitution.
7. Sourcing & Purchasing Guide
Table
Attribute
Details
Primary Distributors
Exact-part listings were returned for DigiKey, Mouser, Arrow, and LCSC, non-R code. For the tape-and-reel code, LCSC directly lists CP2102N-A02-GQFN20R / C969913. These are sourcing leads, not a manufacturer-franchise certification for every channel or region.
Packaging Options
The manufacturer's R suffix denotes optional tape-and-reel packaging. Purchase CP2102N-A02-GQFN20R when the assembly order requires tape/reel format. The exact factory pack type and pack quantity for the non-R code could not be independently confirmed from accessible distributor page content; do not assume it is cut tape or a tray. Distributor cut/repack options must be confirmed at checkout.
Standard MOQ
The directly read LCSC C969913 listing offers 1 piece minimum, a 1-piece order multiple, and 1500 pieces per full reel. LCSC purchasing source. This is a distributor-specific sales option, not a guaranteed MOQ for every distributor. MOQ and non-R factory-pack quantity at DigiKey/Mouser remain unverified because their requested page reads were unavailable.
Sourcing Advice
Prefer manufacturer-authorized/franchised channels and verify authorization for the purchasing region. Request traceability, original moisture-barrier packaging, and applicable handling information. Avoid untraceable marketplace stock and suspiciously discounted brokers; counterfeit, relabeled, or incorrectly revised stock can defeat qualification. Check A02, GQFN20, and the optional R suffix on the purchase order and label; QFN24/QFN28 are not package substitutes. Check the current lot's moisture-sensitivity/reflow instructions rather than inventing a handling rating.
JLCPCB Assembly
The R-code sourcing lead is LCSC C969913, not the non-R listing. Confirm its current JLCPCB assembly eligibility, inventory, reel/feeder requirements, and footprint mapping in the assembly portal. Basic/Extended classification and assembly availability were not verified in this research.
Availability and Pricing
Listings and live data are a snapshot as of October 7, 2026. No price, stock quantity, lead time, or supply guarantee is claimed in this durable guide; recheck at purchase.
Verification boundaries
CP2102N electrical ratings, the QFN20 pin functions, the reference capacitors/reset/divider, and E110 errata above have validated inline source evidence.
FT231XQ function and headline specifications were verified from FTDI's directly read product page; the new datasheet's indexed extraction was still pending. No drop-in qualification was performed.
AN0046 indexed PDF verification remained pending. Numeric USB layout targets are identified as engineering recommendations; its EFM32-specific external resistor/crystal circuits must not be copied into the CP2102N design.
Manufacturer-required unused CTS/WAKEUP termination values were not verified. The external 10 kΩ recommendations deliberately establish known logic states and are not claimed as datasheet mandates.
Non-R factory-pack details, distributor franchise status for a specific region, JLCPCB assembly classification, actual board thermal performance, and the present Flux footprint's correctness remain unverified.
Sources
Silicon Labs — CP2102N Data Sheet, Rev. 1.5, November 2020. Sections 1; 2.1 and 2.3; 3.1.1, 3.1.2, 3.1.5, 3.1.6 and 3.3; 4.1, 4.3.5, 4.3.7 and 4.3.10; 5.3; 8.1 and 8.2; 10. Revision/date verified from the revision history.
Silicon Labs — CP2102N Errata, Rev. 0.4, March 2019. CP2102N_E110 startup USB line-state limitation and workaround.
Infineon — USB Type-C connector: Rp, Rd, and Ra termination resistors. Primary manufacturer explanation of the fixed 5.1 kΩ UFP Rd value; page shows original posting April 17, 2015. A January 6, 2025 entry belongs to the community translation and is not represented here as the technical document's revision date.
Silicon Labs — AN0046: USB Hardware Design Guidelines. Supplemental general USB routing/shield reference; indexed PDF cross-check and revision/date were still unresolved during this research. Its EFM32-specific application component values are not used as CP2102N requirements.
FTDI — FT231XQ product page. Directly verified functional alternative, 3 Mbaud, QFN20 and 1.8–3.3 V I/O; the page lists FT231X Datasheet Rev. 1.7. Manufacturer datasheet link, whose indexed extraction remained pending.
LCSC — CP2102N-A02-GQFN20R / C969913. Direct distributor listing for MOQ, order multiple, and 1500-piece full-reel quantity; accessed October 7, 2026. Distributor metadata is used for purchasing details, not as a replacement for manufacturer electrical ratings.
1. Quick Specifications
2. Pinout & Connections
3. Standard Application Circuit
USB bus-powered, 3.3 V UART interface
Optional UART activity LEDs: 3.3 V and 5 V calculations