USBLC6-2SC6 Guide


Created a project doc

USBLC6-2SC6 Application and Usage Guide

View Document

USBLC6-2SC6 Application and Usage Guide
The USBLC6-2SC6 is a two-channel, rail-to-rail TVS/ESD protection array for high-speed interfaces, with integrated protection for the associated 5 V rail. Its most common use is protecting USB 2.0 D+ and D− plus VBUS at a connector while maintaining signal integrity up to 480 Mb/s.
1. Quick Specifications
Important: This is a transient suppressor, not a continuous-current 5 A power diode. The 5 A figure applies only to the specified 8/20 µs surge waveform.
2. Pinout & Connections
The verified top-view pin order is 1—I/O1, 2—GND, 3—I/O2, 4—I/O2, 5—VBUS, and 6—I/O1.
3. Standard Application Circuit
Created and verified the USBLC6-2SC6 Application and Usage Guide. It covers specifications, pinout, USB wiring, PCB layout, pitfalls, sourcing, and clearly labels alternatives as functionally similar rather than drop-in compatible.
Does this circuit look correct.

image

Does this circuit look correct.

image

Does this circuit look correct.

image

Does this circuit look correct.

usb_check

Does this circuit look correct.

USBLC6-2SC6 Application and Usage Guide
The USBLC6-2SC6 is a two-channel, rail-to-rail TVS/ESD protection array for high-speed interfaces, with integrated protection for the associated 5 V rail. Its most common use is protecting USB 2.0 D+ and D− plus VBUS at a connector while maintaining signal integrity up to 480 Mb/s.
1. Quick Specifications

Table


ParameterClassificationValueConditions / Notes
Reverse working / line voltage, VRMNormal operating condition5.25 VUSB line-voltage condition.
Breakdown voltage, VBRElectrical characteristic6 V minimumVBUS-to-GND, IR = 1 mA.
Leakage current, IRMElectrical characteristic10 nA typical; 150 nA maximumVRM = 5.25 V.
I/O-to-GND capacitanceElectrical characteristic2.5 pF typical; 3.5 pF maximumVR = 1.65 V.
I/O-to-I/O capacitanceElectrical characteristic1.2 pF typical; 1.7 pF maximumVR = 1.65 V.
Clamping voltage, VCLSurge characteristic12 V maximum at 1 A; 17 V maximum at 5 AAny I/O to GND, 8/20 µs waveform.
Peak pulse current, IPPSurge rating5 A8/20 µs pulse; associated maximum VCL is 17 V.
IEC 61000-4-2 ESDAbsolute rating / qualification15 kV air; 8 kV contact guaranteed Level 4The absolute-rating table also lists 15 kV for contact; use the datasheet feature guarantee of 8 kV contact for system qualification unless ST clarifies the discrepancy.
Junction temperature, TjAbsolute rating−40 to +150 °COperating junction temperature range.
Storage temperature, TstgAbsolute rating−55 to +150 °CDatasheet absolute ratings.
Soldering temperature, TLAbsolute rating260 °C maximum10 s at 5 mm.
PackageMechanicalSOT23-6LSix-lead surface-mount package.
Lead pitchMechanical0.95 mm typicalSOT23-6L dimension e.
Important: This is a transient suppressor, not a continuous-current 5 A power diode. The 5 A figure applies only to the specified 8/20 µs surge waveform.
2. Pinout & Connections

Table


Pin NumberPin NameDescriptionBest Practice
1I/O1Connector-side or transceiver-side terminal of protected data channel 1Route inline with one USB data line; pair with pin 6 and avoid a branch stub.
2GNDESD current returnTie directly to a low-impedance ground plane with the shortest possible trace and a nearby ground via.
3I/O2Terminal of protected data channel 2Route inline with the second USB data line; pair with pin 4 and keep geometry balanced with channel 1.
4I/O2Opposite terminal of protected data channel 2Connect to the other side of the same data-line path; do not swap channels midway through routing.
5VBUSRail clamp reference and protected 5 V bus connectionConnect to USB VBUS/5 V. Place a 100 nF ceramic capacitor from VBUS to GND close to the device.
6I/O1Opposite terminal of protected data channel 1Connect to the other side of the same data-line path; maintain continuous controlled-impedance routing.
The verified top-view pin order is 1—I/O1, 2—GND, 3—I/O2, 4—I/O2, 5—VBUS, and 6—I/O1.
3. Standard Application Circuit
Place the USBLC6-2SC6 between the USB connector and the USB transceiver so D+ passes through I/O1 (pins 1 and 6) and D− passes through I/O2 (pins 3 and 4); channel assignment may be reversed if it is kept consistent. Connect pin 5 to USB VBUS and pin 2 to the board ground plane. The ST application diagram identifies D+in/D+out, D−in/D−out, GND, VBUS, and a 100 nF capacitor from VBUS to GND.
No series resistor, pull-up, or pull-down is inherently required by the protection device. Any USB termination, pull-up, pull-down, or USB-C CC resistors belong to the USB controller/connector design and must be selected independently.
Recommended connection order:
  1. USB connector D+ → one I/O1 pin; opposite I/O1 pin → USB transceiver D+.
  2. USB connector D− → one I/O2 pin; opposite I/O2 pin → USB transceiver D−.
  3. USB VBUS → pin 5 and the protected 5 V rail.
  4. Pin 2 → ground plane using the lowest-inductance path available.
  5. 100 nF X7R ceramic capacitor from pin 5/VBUS to ground, placed immediately beside the device.
4. PCB Layout & Routing Guidelines
  • Place the USBLC6-2SC6 immediately behind the connector, before the protected traces travel deeper into the PCB. ST requires the data-to-I/O, VCC-to-VBUS, and ground-plane-to-GND connections to be as short as possible.
  • Route D+ and D− through the device rather than using long stubs. Preserve the USB 2.0 differential impedance target and keep the two channels length- and geometry-balanced through the local breakout.
  • Use a continuous reference plane beneath the data paths. Do not cut or neck the ground plane to route VBUS; transition VBUS with a short trace/via if necessary.
  • Make the GND connection short and wide, with a ground via adjacent to pin 2. Avoid thermal relief on the ESD return via/pad when assembly rules allow, because added inductance raises transient clamping voltage.
  • Keep the 100 nF VBUS capacitor close to pins 5 and 2. Normal USB VBUS current does not flow through the TVS array, so power-trace width is set by the USB power path, connector, fuse/load switch, and system current—not by the 5 A transient rating.
5. Common Pitfalls / Things to Watch Out For
  1. Placing the suppressor near the MCU instead of the connector. The unprotected trace then acts as an ESD injection path, and parasitic trace inductance increases the voltage reaching the protected IC.
  2. Treating 5 A IPP as a continuous-current rating or omitting the VBUS capacitor. The 5 A rating is for an 8/20 µs pulse only; the local 100 nF capacitor improves the rail clamp during a positive surge.
Also verify the footprint orientation carefully: the mirrored channel pins make a rotated or incorrectly numbered SOT23-6 symbol easy to wire incorrectly.
No verified other-manufacturer drop-in, pin-compatible SOT23-6L replacement was identified. The following are functionally similar USB data-line ESD protectors and require schematic/footprint review:

Table


AlternativeCompatibilityEngineering Notes
Texas Instruments TPD2EUSB30DRTRFunctionally similar only; not pin- or footprint-compatibleTwo channels, 5.5 V VRWM, 0.7 pF typical capacitance, 5 A 8/20 µs surge, USB 3.0 capable; 3-pin 1 mm × 1 mm DRT/SOT-9X3 package. It protects data lines but does not provide the same six-pin inline/VBUS arrangement.
Nexperia PRTR5V0U2XFunctionally similar only; not pin- or footprint-compatibleTwo USB 2.0/high-speed lines, rail-to-rail architecture, 5.5 V standoff, 1 pF typical I/O-to-GND capacitance; 4-pin SOT143B package.
Semtech RClamp0522PFunctionally similar only; not pin- or footprint-compatibleTwo-line, 5 V, flow-through high-speed TVS array with 5 A 8/20 µs surge and low capacitance; uses a compact leadless package and does not duplicate the USBLC6-2SC6 VBUS pin arrangement.
Before substitution, compare VRWM, clamping voltage at the same current waveform, ESD test level, dynamic resistance, capacitance and matching, package pinout, VBUS protection, and temperature range.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary DistributorsST eStore, DigiKey, Mouser, LCSC/JLCPCB; Arrow and other franchised ST distributors may also stock it.
Packaging OptionsManufacturer delivery mode is Tape and Reel; DigiKey and Mouser also offer Cut Tape and custom reel services.
Standard MOQManufacturer full reel: 3,000 units. Distributor cut-tape MOQ is commonly 1 unit at DigiKey/Mouser; LCSC currently lists a small-quantity minimum that may change.
Ordering IdentifiersST MPN: USBLC6-2SC6; package: SOT23-6L; top marking: UL26; LCSC/JLCPCB part: C7519.
Sourcing AdvicePrefer ST-authorized/franchised distributors, especially for production builds. Confirm that the exact suffix is SC6 for SOT23-6L; P6 is the smaller SOT-666 variant and is not footprint-compatible. Verify lot traceability and avoid unverified marketplace stock where relabeling or mixed specifications are possible.
Availability and pricing are time-sensitive; re-check stock immediately before BOM release or procurement.
Sources
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources