Battery Management System Design

flux

To expand from a single-cell to a multi-cell BMS, you’ll need to:
  1. Choose a multi-cell charger/BMS IC
    • Swap out U1 (RT9525) for a dedicated multi-cell monitor/charger such as TI’s BQ76920 (up to 3 cells) or BQ76930 (up to 10 cells).
    • These ICs integrate per-cell voltage sensing, over/under-voltage protection, and passive cell balancing.
  2. Add cell-balance circuitry
    • Each cell requires a bleed resistor network controlled by the BMS IC to equalize voltages.
    • Place balancing MOSFETs or resistors and route individual cell sense lines back to the new BMS IC.
  3. Revise voltage dividers and sense nets
    • Replace your single VSYS sense resistor divider ([R3]/[R4]) with an array of dividers for each cell.
    • Create separate nets (CELL1, CELL2, …) tied to the IC’s CELLx pins.
  4. Upgrade connectors and insulation
    • Use a higher-voltage pack connector rated for the total stack voltage (e.g., 12.6 V for 3 cells).
    • Ensure creepage/clearance distances and high-voltage isolation for ESP32 level shifters or use an isolated ADC interface.
  5. Adapt the power-rail architecture
    • The TPS62160 input (VSYS) must handle the pack’s full voltage range; check its max VIN (36 V).
    • Consider a pre-regulator or a higher-voltage buck if your cell count exceeds its rating.
  6. Update firmware and GPIO assignments
    • Map the new BMS status flags (OV, UV, CHG, DSG) to ESP32 GPIOs.
    • Implement per-cell voltage monitoring and balancing commands in your firmware.
  7. Layout and thermal considerations
    • Based on Flux KB guidance, “when designing single-cell BMS, compare to 2-cell …” you must now prioritize “component placement to minimize high-voltage loop areas” and ensure copper spacing meets the pack’s max voltage.
    • Distribute thermal vias under the BMS IC to dissipate balancing heat.
  8. Safety and protection add-ons
    • Add input reverse-polarity protection (Schottky or ideal diode) and a TVS array rated to the stack voltage.
    • Include an NTC thermistor on each cell group (as supported by many multi-cell BMS ICs).
By following these steps—selecting a multi-cell BMS IC, routing individual cell sense/balance lines, upgrading connectors, and revising power rails—you’ll extend your design to reliably charge, monitor, and balance multiple cells.
rahmmed

rahmmed

can you change it for me?

flux

Components to Add

Table

Part NamePurposeManufacturer Part NumberQuantityFootprintDatasheet link
BQ7692000PWR3-cell battery monitor & balancer IC to replace the single-cell RT9525 and manage per-cell sensing and balancingBQ7692000PWR1TSSOP-20PDF
Components to Remove
  • U1
    (RT9525 single-cell charger IC)
+3V3
R1
Resistance
1.5kΩ
VIN
+3V3
R6
Resistance
10kΩ
R2
Resistance
1.5kΩ
VIN
+3V3
VBAT
+3V3
R3
Resistance
10kΩ
VSYS
VSYS
VSYS
R4
Resistance
1kΩ
R5
Resistance
100kΩ
VBAT
VBAT
+3V3
VIN
VBAT
C1
Capacitance
10uF
EN1
CHRG_EN
EN2
SYSOFF
SYSOFF
C5
Capacitance
22uF
EN1
EN2
ESP_EN
CHRG_EN
C6
Capacitance
10uF
H1
IC1
H2
H3
C4
Capacitance
1uF
U2
C3
Capacitance
2.2uF
C2
Capacitance
1uF
U1
L1
Inductance
2.2uH
C7
Capacitance
0.1uF
POWER
BAT
SYSTEM
3V
RX
G
TX
LED2
LED1
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
    jharwinbarrozo
    16.6k
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • RMCF0805JT47K0
    RMCF0805JT47K0
    General Purpose Thick Film Standard Power and High-Power Chip Resistor 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film Features: - RMCF – standard power ratings - RMCP – high power ratings - Nickel barrier terminations standard - Power derating from 100% at 70ºC to zero at +155ºC - RoHS compliant, REACH compliant, and halogen free - AEC-Q200 compliant
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10 µF 16 V Aluminum - Polymer Capacitors Radial, Can - SMD 30mOhm 2000 Hrs @ 105°C #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric)
    jharwinbarrozo
    1.1M
  • 1070TR
    1070TR
    Battery Holder (Open) Coin, 20.0mm 1 Cell SMD (SMT) Tab bate or batt #forLedBlink
    jharwinbarrozo
    700.5k

RT9525 ESP32 Wireless BMS

RT9525 ESP32 Wireless BMS thumbnail
This is ESP32-S3-MINI-1 Wireless BMS project for a battery charger based on the RT9525 battery charger IC from Richtek. #project #ESP32 #ESP32S3 #charger #batterycharger #template #bms #monitor #RT9525 #richtek #polygon

Properties

creativecommons.org/licenses/by/4.0/

Pricing & Availability

Distributor

Qty 1

Controls