JLCPCB Parts Check


Please check whether any of these components in this PCB are out of stock at JLCPCB. If any are unavailable, please find alternatives. Prefer basic type parts.
I need at least five PCBs.
I’ll audit the BOM against current JLCPCB/LCSC assembly stock for a five-board build, then identify footprint- and spec-compatible substitutes, prioritizing Basic parts. I’ll record the full availability and replacement table in a project file.
The BOM extraction is complete. Five-board demand is modest, but several listed items currently show zero/unknown JLCPCB/LCSC stock; I’m now separating true shortages from BOM metadata gaps and checking Basic substitutes.
Audit complete for five PCBs. Two parts need action: the gate-driver optocouplers require 20 units but their current SKU is unavailable, and the flash memory needs replacement due to both sourcing and 3.3 V compatibility; several apparent shortages were stale data and are currently stocked.
Full results and alternatives: JLCPCB Replacement Parts
Next steps
  • Replace the flash and update its footprint.
  • Select and validate the stocked optocoupler alternative.
  • Assign exact JLCPCB/LCSC sourcing codes to the BOM.

3.3 V Power Budget
Decision
An RT6150B adjustable-output regulator rated for up to 800 mA continuous output is adequate for the populated on-board 3.3 V loads, provided VSYS is near 5 V, the exposed pad and capacitors are laid out correctly, and the 3V3 output on FPC1 pin 1 is not expected to supply more than about 150–200 mA continuously.
The design is not expected to consume 800 mA in normal operation. A conservative supply-capability budget is approximately 600 mA, leaving about 200 mA (25%) below the regulator headline rating.
Schematic Load Inventory
Direct consumers found on the 3V3 rail:

Table


LoadNormal / datasheet figureConservative design allowance
ESP-WROOM-02D-N480 mA average; highest listed Wi-Fi TX typical is 170 mA500 mA supply-capability allowance for RF transients
RP2350A including internal 1.1 V regulatorAbout 12–16 mA in listed typical example workloads50 mA
W25Q32RV flashUp to 20 mA during high-speed reads; 15 mA program/erase20 mA
Pull-ups, divider networks, leakage, indicators and miscellaneous logicSmall relative to radio load30 mA
External load through FPC1 pin 1UnknownMust be specified
Known-board conservative subtotal~600 mA
The realistic simultaneous operating current is more likely around 250–350 mA, but the 600 mA figure is the safer regulator-sizing basis because the ESP8266 module explicitly recommends a supply capable of at least 500 mA.
Margin Assessment
  • Regulator headline rating: 800 mA continuous.
  • Conservative populated-board allowance: ~600 mA.
  • Remaining allowance: ~200 mA, or 25% of rated output.
  • Recommended external 3V3 load limit: 150 mA continuous to preserve useful tolerance, temperature, transient, and aging margin.
  • If FPC1 powers a display, sensor assembly, or other board drawing more than 150–200 mA, select a regulator with at least 1.0–1.2 A guaranteed output instead.
OV5642 Camera Allowance
The OV5642 documentation does not publish a completed active-current value; both active and standby current fields are marked TBD. A documented OV5642 camera module variant accepts a single 3.3 V input and contains the sensor's 1.5 V core regulator, but module construction varies.
For power-path sizing, reserve:
  • 150 mA as a reasonable expected active-camera load.
  • 200 mA as the normal conservative design allowance.
  • 250 mA for connector, regulator, and worst-case power-budget sizing until the exact camera module is identified or measured.
Using a 200 mA camera allowance, expected simultaneous board demand is approximately 400–500 mA during active Wi-Fi and image capture. A conservative transient budget is approximately 650–750 mA. Therefore, an 800 mA RT6150B is still likely adequate, but the remaining margin is small and depends on input voltage, temperature, capacitor effectiveness, and the exact camera module.
For a robust production design where Wi-Fi transmission and full-rate camera capture may occur simultaneously, prefer a regulator with at least 1.0 A guaranteed output, ideally 1.2 A, rather than designing continuously near the RT6150B's headline limit.
The current FPC1 pin mapping does not match the commonly published 20-pin parallel OV5642 module pinout, so the exact camera/module manufacturer part number must be confirmed before treating these estimates as guaranteed.
Adjustable-Version Changes Required
The existing U1 is the fixed RT6150B-33GQW implementation and its FB pin is directly connected to 3V3. The adjustable version cannot be fitted without a schematic change.
For 3.3 V adjustable operation:
  • Use the adjustable RT6150B ordering option; confirm the exact purchasable MPN with the distributor before replacement.
  • Add a feedback divider from VOUT to FB to GND.
  • Datasheet example values are 487 kΩ upper and 86.6 kΩ lower, using a nominal 0.5 V feedback reference.
  • A feed-forward capacitor across the upper resistor may be used for improved transient response; with the example resistor value the datasheet equation yields approximately 0 pF, so verify the intended adjustable application diagram and selected resistor pair.
  • Keep the existing 2.2 µH inductor only after verifying its saturation-current rating exceeds converter peak current; the regulator switch current-limit minimum is listed as 1.6 A.
  • Provide at least 10 µF effective input capacitance and 10 µF effective output capacitance close to U1. The typical application shows 10 µF input and 20 µF output. Account for MLCC DC-bias derating.
  • The WDFN exposed pad must connect to a strong ground plane.
Important Constraints
  1. FPC1 pin 1 exports 3V3. Its external current is not defined in the schematic, so the 800 mA conclusion is conditional on that load.
  2. GPIO-sourced loads are additional. RP2350 example power figures are measured with almost all GPIOs unloaded.
  3. Input voltage matters. “Up to 800 mA” is not a guarantee at every boost-mode input voltage. This project appears to operate U1 from the VSYS/5 V domain, which is the favorable buck-mode case. If VSYS can fall below 3.3 V, validate available output current at the minimum input voltage.
  4. Thermal and layout quality matter. The 2.5 mm WDFN package requires the exposed pad and low-impedance power/ground routing for continuous high-current operation.
Verification Status
The schematic rail membership was verified directly in the current project. Regulator, ESP-WROOM-02D, RP2350A, and W25Q32RV figures were extracted from their datasheets; the datasheet lookup returned OCR text without resolvable inline citation identifiers in this session, so critical production values should be checked once more against the current manufacturer PDFs and distributor ordering page before procurement.
  • Decision

  • Schematic Load Inventory

  • Margin Assessment

  • OV5642 Camera Allowance

  • Adjustable-Version Changes Required

  • Important Constraints

  • Verification Status