PCB Layout Conflict

pasted-text-1784225147226.txt

Thought for 10 sec

flux

I’ll open the attached text to see what you want done, then I’ll summarize or act based on its contents.

Worked for 4 mins 4 sec

Created a project doc

Pinch Breakout REV A1 — Project Specification

View Document

Breadboard adapter for the Moddo pinch connector/header pattern. The board adapts a central 2×8, 1.27 mm pitch male header to surrounding 2....

flux

I created the project spec and renamed the project. Next I’m adding the through-hole headers and wiring the requested net map.

Worked for 7 mins 58 sec

flux

I’m blocked by a mechanical conflict in the pasted placement map: the left-column bottom hole is D5 at X=0, Y=0, while the bottom-row left hole is RST at the same X=0, Y=0, so two different nets occupy the same drill hole.

Completed so far:

Created the project spec: Pinch Breakout REV A1 — Project Specification
Renamed/described the project.
Added H1/J2/J3/J4 and wired the schematic netlist.
Set the PCB to 18 × 15 mm, 2 layers, and started through-hole pad geometry.

To continue, I need one clarification: should the bottom row start at X=2.54 mm instead of X=0 so it does not overlap the left column, or is one of the listed corner nets incorrect?

Offset bottom row

Corner net correction

Fix overlap directly

Recheck after fix

Files

Schematic

Layout

Preview

H1 Pin_5 - J3 Pin_5

H1 Pin_7 - J3 Pin_6

H1 Pin_6 - J4 5

H1 Pin_9 - J2 Pin_6

H1 Pin_11 - J2 Pin_5

H1 Pin_2 - J3 Pin_2

H1 Pin_12 - J4 1

H1 Pin_10 - J4 2

H1 Pin_9 - J2 Pin_6

H1 Pin_1 - J3 Pin_3

H1 Pin_4 - J3 Pin_1

H1 Pin_14 - J2 Pin_1

H1 Pin_15 - J2 Pin_3

H1 Pin_1 - J3 Pin_3

H1 Pin_10 - J4 2

H1 Pin_3 - J3 Pin_4

H1 Pin_11 - J2 Pin_5

H1 Pin_16 - J2 Pin_2

H1 Pin_3 - J3 Pin_4

H1 Pin_15 - J2 Pin_3

H1 Pin_6 - J4 5

H1 Pin_5 - J3 Pin_5

H1 Pin_4 - J3 Pin_1

H1 Pin_14 - J2 Pin_1

H1 Pin_7 - J3 Pin_6

H1 Pin_16 - J2 Pin_2

H1 Pin_8 - J4 4

H1 Pin_2 - J3 Pin_2

H1 Pin_8 - J4 4

H1 Pin_12 - J4 1

GND

Pinch Breakout REV A1 — Project Specification

Purpose

Breadboard adapter for the Moddo pinch connector/header pattern. The board adapts a central 2×8, 1.27 mm pitch male header to surrounding 2.54 mm through-hole breakout headers.

Mechanical Requirements

Board outline: 18 mm × 15 mm rectangle.
PCB stackup: 2 layers.
Mounting/assembly: all parts are through-hole; every pad must have a drill, no SMD pads.
Copper routing: 0.3 mm traces.
Bottom copper: GND pour.
Top silkscreen: net name at each breakout hole plus title text pinch Breakout / REV A1.

Parts

H1: male header, 2×8, 1.27 mm pitch; drill Ø0.65 mm, pad Ø1.0 mm.
J2, J3: male header, 1×6, 2.54 mm pitch; drill Ø1.0 mm, pad Ø1.7 mm.
J4: male header, 1×5, 2.54 mm pitch; drill Ø1.0 mm, pad Ø1.7 mm.

H1 Netlist

Table

H1 Pin	Net
1	3V3
2	D0_SCL
3	VBUS
4	D1_SDA
5	D7_MOSI
6	D2
7	D8_MISO
8	D3
9	D9_SCK
10	D4
11	D10_SS
12	RST
13	GND
14	D5_TX1
15	D11_DAC0
16	D6_RX1

Breakout Placement Map

Coordinate datum: origin is the bottom-left breakout hole. 2.54 mm grid.

Left column, X = 0, bottom → top: D5, D6, D11, GND, D10, D9.
Right column, X = 15.24 mm, bottom → top: D1, D0, 3V3, VBUS, D7, D8.
Bottom row, Y = 0, left → right: RST, D4, GND, D3, D2.
H1 centered at (7.62 mm, ~4.75 mm), rows horizontal, pin 1 top-right; top row right → left: 1, 3, 5, …, 15.

Validation Criteria

All listed nets connect one H1 pin to the corresponding 2.54 mm breakout hole; GND connects to both breakout GND holes.
All component pads are plated through-hole with the specified drill and pad diameters.
Board is 18 mm × 15 mm, 2-layer, with 0.3 mm routing and a bottom GND pour.
No unresolved ERC/DRC issues after routing, or any remaining issues are documented.

Purpose
Mechanical Requirements
Parts
H1 Netlist
Breakout Placement Map
Validation Criteria