Project Start Help


Thought for 9 mins 13 sec
Thought for 6 sec
2/6 Build the complete editable schematic with datasheet-backed parts and required GPIO mapping

Create project specification and engineering architecture for Doseband X

Build the complete editable schematic with datasheet-backed parts and required GPIO mapping

Verify schematic connectivity and resolve ERC issues

Create the wearable PCB outline and place components

Route the PCB with USB, RF, analog, power, and ground constraints

Run final DRC and verify manufacturing readiness

Thought for 22 sec
Created a thread
Doseband X Schematic
Needs input
View Thread
Thought for 6 sec
Awaiting 1 background task
"Doseband X Schematic" completed.
The initial design pass created the Project Specification and added 58 real components, including the ESP32-S3-WROOM-1-N16R8, BQ24074 power-path charger, TPS63001 buck-boost regulator, SHTC3 sensor, USB-C/ESD circuitry, H2S interfaces, RGB LED, and motor-driver parts.
Open items
  • The project currently reports 0 nets, so the schematic has not been electrically wired or ERC-verified.
  • PCB outline, placement, antenna keepout, routing, ground plane, and DRC remain unfinished.
  • The added components still require reconciliation against the exact H2S path and GPIO mapping before layout.
Execution stopped because your ACUs ran out.

Project Specification
Project Overview
  • Device: Doseband X — Passive Colorimetric H2S Exposure-Dosimeter Wristband with optional electronic chemiresistive measurement.
  • Status: Approved for prototype design.
  • Purpose: Wearable monitoring platform combining a cumulative passive color strip with an electrically separate H2S-responsive cartridge and smartphone-assisted quantitative interpretation.
Intended Use
  • SIH 2026 engineering prototype for wearable H2S exposure indication and measurement development.
  • Not certified personal protective equipment or a life-safety gas alarm in this revision.
What the Device Should Do
  • Carry a disposable passive colorimetric H2S exposure strip.
  • Measure a separate two-electrode chemiresistive H2S cartridge through an ESP32-S3 ADC input.
  • Compensate readings using temperature and humidity.
  • Communicate through native USB, Bluetooth, and Wi-Fi.
  • Support an external I2C OLED, RGB status indication, pushbutton, and vibration alert.
  • Operate from a rechargeable single-cell Li-Po battery and charge from USB-C.
Main Features
  • ESP32-S3 module with integrated antenna and production-ready flash/PSRAM.
  • USB-C sink with native USB data, CC resistors, ESD protection, and series termination.
  • Li-Po charger with power-path management and protected SYS rail.
  • Efficient regulated 3.3 V rail sized for ESP32 radio current peaks.
  • Temperature/humidity sensor on I2C.
  • Separate H2S cartridge contacts and selectable test-resistance substitute.
  • UART/debug access.
System Architecture

Diagram


ADC D+ / D- USB-C 5 V + USB Data Li-Po Charger and Power Path 1-cell Li-Po SYS Rail 3.3 V Regulator ESP32-S3 Temperature and Humidity Sensor I2C OLED Connector Chemiresistive H2S Divider RGB LED Vibration Motor Driver
Hardware Subsystems
  • Power / USB-C: USB-C receptacle, CC1/CC2 5.1 kΩ sink pull-downs, VBUS and USB data ESD protection.
  • Battery / Charging: Single-cell Li-Po connector, modern charger/power-path IC, conservative wearable-cell charging current, battery temperature support when practical.
  • 3.3 V Regulation: Low-IQ regulator capable of ESP32-S3 transient current without losing regulation across the usable Li-Po range.
  • Compute / RF: ESP32-S3 module, required boot/reset biasing, local decoupling, antenna keepout on every copper layer.
  • H2S Measurement: +3V3 → R_FIXED → H2S_ADC/GPIO4 → H2S_E1 → external sensing material → H2S_E2 → GND. No resistor across or below the cartridge.
  • Environmental Compensation: Compact low-power I2C temperature/humidity sensor with local decoupling.
  • User Interface: External OLED connector, low-current RGB LED, GPIO0 button, vibration motor MOSFET driver.
  • Debug: Native USB and accessible UART TX/RX plus reset/boot access.
Interfaces and Connections

Table


NetESP32-S3 assignmentPurpose
H2S_ADCGPIO4Chemiresistive divider measurement
I2C_SCLGPIO5I2C clock
I2C_SDAGPIO6I2C data
RGB_RGPIO15Red LED channel
RGB_GGPIO16Green LED channel
RGB_BGPIO17Blue LED channel
VIB_CTRLGPIO18Vibration driver control
BUTTONGPIO0Active-low user/boot button
USB_DMGPIO19Native USB D-
USB_DPGPIO20Native USB D+
Power and Runtime Expectations
  • Source: one protected or externally protected 1-cell Li-Po, nominal 3.7 V.
  • USB input: 5 V Type-C sink, no USB Power Delivery.
  • Runtime depends strongly on radio/display/motor duty cycle and battery capacity; firmware must use sleep and duty-cycled radios for wearable operation.
Power Tree and Preliminary Power Budget

Table


LoadTypical/active estimatePeak design allowance
ESP32-S3 module80–240 mA active500 mA radio transient
Temperature/humidity sensor<2 mA3 mA
External OLED20 mA40 mA
RGB LED3–9 mA15 mA
H2S dividerresistance-dependent<0.33 mA with 10 kΩ fixed resistor
Miscellaneous5 mA15 mA
3.3 V rail target~275 mA active≥600 mA transient capability
Vibration motor on SYS/VBAT60–100 mA150 mA startup allowance
The charger, battery connector, protection path, and SYS wiring should support at least 0.8 A transient load with margin. The 3.3 V regulator must be rated for at least 0.6 A and verified across the battery discharge range.
H2S Measurement Equation
  • V_ADC = 3.3 × R_SENSOR / (R_FIXED + R_SENSOR)
  • R_SENSOR = R_FIXED × V_ADC / (3.3 − V_ADC)
  • Initial R_FIXED target is 10 kΩ; it may be revised when the real sensing material resistance range is characterized.
  • A potentiometer or resistor network may be fitted only as H2S SENSOR TEST ONLY, selected instead of the real cartridge and never placed in parallel.
Manufacturing and Assembly Expectations
  • Standard 2-layer or 4-layer SMD PCB using obtainable manufacturer parts and verified footprints.
  • Prefer 0603 passives for prototype assembly where size permits; smaller packages only where placement density requires them.
  • Board approximately 55 mm × 25 mm with rounded corners; size may increase if routing or RF constraints require it.
Firmware-Relevant Hardware Requirements
  • Native USB programming/debug plus exposed UART TX/RX.
  • GPIO0 must remain correctly biased for normal boot and support manual download mode.
  • ADC acquisition should average/filter samples and reject rail-saturation readings.
  • Firmware must compensate the H2S estimate using temperature/humidity calibration data.
Physical Design Expectations
  • USB-C, battery, OLED, motor, and H2S cartridge interfaces accessible from board edges.
  • ESP32 antenna at an outward-facing edge with datasheet keepout on all layers.
  • H2S analog path short and separated from regulator switching nodes, motor current, and USB traces.
  • Temperature/humidity sensor isolated from charger, regulator, ESP32, motor, and other heat sources.
Important Design Decisions
  • The passive color strip is mechanically carried/read optically and is electrically independent.
  • The electrical cartridge is a true external two-electrode chemiresistive element, not a PCB resistor.
  • Native ESP32-S3 USB removes the need for a USB-UART bridge.
  • Power-path charging is preferred so the device can operate safely while connected to USB.
Assumptions
  • The Li-Po cell includes certified cell-level protection, while the PCB adds charger/power-path protection appropriate to the selected IC.
  • The external vibration motor is a small brushed coin motor compatible with the SYS/VBAT range.
  • The final fixed-divider resistor may require a build option after cartridge characterization.
  • This prototype is not yet certified for occupational safety or medical use.
Change Notes
  • Initial specification created from the supplied SIH 2026 requirements.
  • Project Overview

  • Intended Use

  • What the Device Should Do

  • Main Features

  • System Architecture

  • Hardware Subsystems

  • Interfaces and Connections

  • Power and Runtime Expectations

  • Power Tree and Preliminary Power Budget

  • H2S Measurement Equation

  • Manufacturing and Assembly Expectations

  • Firmware-Relevant Hardware Requirements

  • Physical Design Expectations

  • Important Design Decisions

  • Assumptions

  • Change Notes