Device Proximity Alert System


Thought for 3 mins
Thought for 6 sec
1/3 Record the approved concept and derive provisional mechanical constraints.

Record the approved concept and derive provisional mechanical constraints.

Build and check the enclosure, bracket and internal placeholders.

Capture prototype electronics and firmware starter, then review remaining gaps.

Thought for 8 sec
Referenced guidance.
Thought for 8 sec
Reading "industrial-design-brief" project doc.
Thought for 6 sec
Reading "project-specification" project doc.
Thought for 11 sec
Awaiting 1 task
Thought for 33 sec
Awaiting 1 task
"Vehicle Proximity Alert Risk Review" completed.
Thought for 25 mins 12 sec
Thought for 8 sec
Awaiting 1 task
Thought for 5 sec
Reading project docs.
"Vehicle Alert Enclosure Design" completed.
I recorded your concept approval and created a partial enclosure CAD assembly, provisionally 120 × 145 × 47.8 mm. Seven models are placed: the shell, front lid, board carrier, bracket, and board/display/battery placeholders; editable sources and handoff details are saved in the Mechanical Build Report.
It is not ready to print. Remaining work includes:
  • Repair the bracket mounting slots and check pivot clearance.
  • Place buttons and hardware, then verify assembly fit and screw paths.
  • Select actual display and battery parts; their current shapes are placeholders.
  • Build the electronics and firmware—there are still no electrical components or nets.
Execution stopped because your ACUs ran out.

Waiting for input


No schematic yet

Talk to Flux to get started.

Enclosure Concept
Status: Concept v1 explicitly accepted by user; acceptance relayed by lead on 2026-10-26. CAD is a boardless first pass, not production fit.

Accepted concept

The drawing is the binding reference for silhouette, proportions, and control layout. Values marked derived from drawing may be adjusted to match the drawing; values marked hard constraint may not.

Table


Form/inputReadingState
Front height/widthSlight portrait, approximately 1.1–1.2; perspective prevents exact ratioderived from drawing
Rear height/widthSimilar rounded silhouette to front, approximately 1.1–1.2derived from drawing
Face angleMostly upright on dashboard, about 90° from mounting plane at neutral bracket posederived from drawing
Corner radiusAbout 0.08–0.12 face heightderived from drawing
SeamRemovable front face perimeter, parallel rear silhouettederived from drawing
DisplayLarge centered upper region, roughly upper 65–70% including bezel; aspect/proportion foreshortenedderived from drawing
ControlsSET left and ACK right at about 25%/75% width on lower row; sounder centered betweenderived from drawing
Rear depthHidden by exploded perspective; derive from contents, not pixel distanceUNKNOWN
BracketAdjustable pivot pedestal with dashboard fastening slotsderived from drawing
Intended PCB100 × 120 × 1.6 mm, top 10 mm / bottom 2 mm Estimated; four holes inset 4 mm PROVISIONALhard constraint
Battery reservationProtected 1-cell pack envelope 70 × 55 × 18 mm Estimated behind board; no runtime claimhard constraint
Display reservationApproximate 85 × 60 mm aperture Estimated, not a selected component or mating fithard constraint
Named portsRear 12 V, RF, GNSS only; exact cable fittings unknownhard constraint
ProcessPETG FDM, 0.4 mm nozzle, self-tapping front lid and PCB retentionhard constraint
Relative Layout Map
  • Rounded, slightly portrait face follows accepted drawing.
  • Display centered in upper face; SET on left and ACK on right below, with central sounder.
  • Rechargeable battery behind carrier; separate from future power-electronics keep-out.
  • Three rear-facing cable entry reservations, named 12 V, RF, GNSS.
  • Adjustable bracket under housing; front seam removable for service.
Interpretation and Limits
Rear depth is unspecified by the drawing and may safely be derived from the instructed content stack. All aperture/hardware-dependent dimensions remain Estimated/PROVISIONAL until sourced parts and print coupons are available. This is splash-resistance concept only, not an experimental sealed design or IP-rated product. Membrane/gasket provisions do not establish sealing; pressure equalization remains a thermal/safety follow-up with no unsourced vent geometry. Charging must use measured cell temperature and inhibit outside the actual selected cell limits; PETG is not qualified for a hot dashboard.
  • Relative Layout Map

  • Interpretation and Limits