flux

#Goal

- Fix the schematic by removing duplicate designator J5, ensuring that only one instance exists for the momentary switch interface. Establish correct connections with Pin1 wired to ESP32-C3 U4:IO5 (MSW_SIG) and Pin2 to GND, and verify that the revised schematic passes ERC/DRC/Review checks without duplicate designators or connection issues.

#Implementation plan

1. Identify duplicate J5 connectors

1. Review the schematic to locate all instances labeled J5.

2. Determine which instance correctly serves as the intended momentary switch interface.

2. Remove or rename the duplicate J5

1. Delete or update the designator of the redundant J5 instance, ensuring a single unique J5 remains in the schematic.

3. Confirm and restore the micro switch (MSW) interface connections

1. Verify that Pin1 of the remaining J5 is connected to ESP32-C3 U4:IO5 (MSW_SIG).

2. Verify that Pin2 of the remaining J5 is connected to GND.

3. Reroute any connections as necessary to avoid breaks from deletion.

4. Validate schematic and design inputs

1. Run ERC/DRC/Review to ensure there are no duplicate designators or isolated nets.

2. Iteratively correct any remaining warnings raised during review.

#Success criteria

- The design contains only one instance of designator J5.

- The micro switch interface is correctly connected: Pin1 to ESP32-C3 U4:IO5 and Pin2 to GND.

- The schematic passes ERC/DRC/Review checks with no duplicate designator or connectivity issues.

Removed J6

⚠️ Removed components had their net connections destroyed. Use the connections tool with a `view` action to verify connectivity and re-wire any lost connections.

Connected J5:P1, U4:IO5 to ^MSW_SIG

Connected J5:P2 to ^GND

nets {

net +3V3 = C17:P1, R5:P2, C19:P1, FPC1:1, R4:P2, C18:P1, U5:VREGIN, U5:VDD, U3:VOUT, C22:P1, R13:P2, C24:P1, U4:3V3;

net GND = FPC1:2, J1:2, C13:P2, R3:P2, C1:P2, C19:P2, C3:P2, R1:P2, C15:P2, Q1:S, C12:P2, C9:P2, C7:P2, IC1:GND, C11:P2, U4:53, U4:52, U4:51, U4:50, U4:49, U4:48, U4:47, U4:46, U4:45, U4:44, U4:43, U4:42, U4:41, U4:40, U4:39, U4:38, U4:37, U4:36, U4:2, U4:1, U2:VSS, U3:GND, D1:A1, C24:P2, R14:P1, C23:P2, C22:P2, U3:EP, C21:P2, U3:PGND, U1:GND, USB1:A1, USB1:B12, USB1:A12, USB1:B1, U4:11, U4:14, U5:21, U5:3, U5:12, C14:P2, C10:P2, C16:P2, C2:P2, C5:P2, SW2:P1, SW1:P1, C18:P2, Q2:S, C17:P2, J2:PIN2, C8:P2, C20:P2, R2:P2, C6:P2, C4:P2, J4:P2;

net HALL_SIG = U4:IO4, FPC1:3;

net UART_RX0 = U5:17, U4:TXD0;

net GND = J6:Pin_2, GND:GND, J5:P2;

net EN = Q1:D, U4:EN, R4:P1, SW1:P3;

net BOOT0 = Q2:D, SW2:P3, R5:P1, U4:O0;

net SERVO_PWM = J1:3, U4:IO6;

net UART_TX0 = U4:RXD0, U5:TXD;

net AUDIO_PWM = U4:IO7, R6:P2;

net MSW_SIG = J5:P1, U4:IO5;

}

Removed J5

Removed J5

⚠️ Removed components had their net connections destroyed. Use the connections tool with a `view` action to verify connectivity and re-wire any lost connections.

flux