Switches
A switch is a device that allows electricity to flow through a circuit by completing or interrupting the connection. It is a common component in electrical and electronic systems and is used in a variety of applications, such as controlling the flow of electricity in a circuit, turning devices on and off, and routing electrical signals. One of the primary use cases for switches is to control the flow of electricity in a circuit. This can be done by manually flipping the switch or by using a control mechanism, such as a timer or a sensor. Another common use for switches is to turn devices on and off. This can be done using a switch that is built into the device or by using a separate switch that is connected to the device. In addition to these basic use cases, switches can also be used to route electrical signals. For example, a switch can be used to route a signal from one device to another or to direct a signal to a specific circuit or component. If you're looking for a wide variety of switches for your projects, flux.ai has the world's largest community-driven public library of them. The library includes footprints, symbols, datasheets, and simulation models for a wide range of switches, making it easy to find the right switch for your needs.
AP63205WU-7
3.8V to 32V Input, 2A Low Quiescent Current Synchronous Buck Converter with Enhanced EMI Suppression The AP63200/AP63201/AP63203/AP63205 is a 2A, synchronous buck converter with a wide input voltage range of 3.8V to 32V and fully integrates a 125mΩ high-side power MOSFET and a 68mΩ low-side power MOSFET to provide high-efficiency step-down DC/DC conversion. The AP63200/AP63201/AP63203/AP63205 device is easily used by minimizing the external component count due to its adoption of peak current mode control along with its integrated compensation network. The AP63200/AP63201/AP63203/AP63205 has optimized designs for Electromagnetic Interference (EMI) reduction. The converter features Frequency Spread Spectrum (FSS) with a switching frequency jitter of ±6%, which reduces EMI by not allowing emitted energy to stay in any one frequency for a significant period of time. It also has a proprietary gate driver scheme to resist switching node ringing without sacrificing MOSFET turn-on and turn-off times, which further erases highfrequency radiated EMI noise caused by MOSFET switching. The device is available in a low-profile, TSOT26 package • VIN 3.8V to 32V • 2A Continuous Output Current • 0.8V ±1% Reference Voltage • 22µA Ultralow Quiescent Current • Switching Frequency o 500kHz: AP63200 and AP63201 o 1.1MHz: AP63203 and AP63205 • Pulse Width Modulation (PWM) Regardless of Output Load o AP63201 • Supports Pulse Frequency Modulation (PFM) o AP63200, AP63203, and AP63205 o Up to 80% Efficiency at 1mA Light Load o Up to 88% Efficiency at 5mA Light Load • Fixed Output Voltage o 3.3V: AP63203 o 5.0V: AP63205 • Proprietary Gate Driver Design for Best EMI Reduction • Frequency Spread Spectrum (FSS) to Reduce EMI • Precision Enable Threshold to Adjust UVLO • Protection Circuitry o Overvoltage Protection o Cycle-by-Cycle Peak Current Limit o Thermal Shutdown #CommonPartsLibrary #IntegratedCircuit #PowerManagement
169 Uses0 StarsKH-6X6X5H-STM
SWITCH TACTILE SPST SMD The KH-6X6X5H-STM is a compact surface-mount tactile push-button switch manufactured by Kinghelm. It is a 6 mm × 6 mm momentary SPST (Single Pole Single Throw) switch designed for user-input functions in consumer electronics, industrial controls, embedded systems, IoT devices, and portable equipment. The switch provides tactile feedback when pressed and automatically returns to its normal state when released. Key Features Tactile momentary switch with click feedback SPST normally-open contact configuration 6 mm × 6 mm footprint 5 mm actuator height Surface-mount (SMT) package 4-pin gull-wing terminals 12 V DC rated voltage 50 mA contact current rating 80,000-cycle mechanical life Round black actuator button Vertical actuation design Compact size suitable for dense PCB layouts RoHS compliant Typical Applications Power and reset buttons Consumer electronics Remote controls IoT and smart devices Industrial control panels Portable instruments Embedded development boards Home appliances and control interfaces For PCB library creation, the component is commonly classified as: Component Type: Tactile Switch Switch Configuration: SPST-NO Mounting Type: Surface Mount (SMT) Package: SMD-4P, 6×6 mm Designator Prefix: SW #CommonPartsLibrary #Switch
1.5k Uses0 Stars