Inductors

15µH Shielded Drum Core, Wirewound Inductor 5.45 A 25.8mOhm Max Nonstandard The 7447798151 is a 15 µH shielded wirewound drum core inductor optimized for high current power applications. It features low DC resistance and high saturation current capability, making it suitable for compact, high-frequency power designs. Key Features Inductance: 15 µH High current rating: up to 5.45 A (RMS) Saturation current: ~4 A Low DC resistance: 25.8 mΩ max Shielded construction for low EMI / magnetic leakage High self-resonant frequency: ~19 MHz Wide operating temperature: -40°C to +150°C Compact SMD package (~10.2 mm × 10.2 mm footprint) Typical Applications DC-DC converters (buck / boost) Power supply filtering Automotive and industrial power systems Point-of-load (POL) regulators High-frequency switching circuits #WurthElektronik #WEPDF #PowerInductor #15uH #SMDInductor #ShieldedInductor #PowerElectronics #ElectronicsComponents #SMTComponents #CommonPartsLibrary #Fixed-Inductor

10 µH Shielded Drum Core, Wirewound Inductor 7.5 A 30mOhm Max Nonstandard # Engineering Specification ## Product Name SRP1038A-100M ## General Description SRP1038A-100M is a shielded surface mount power inductor designed for use in high-efficiency DC-DC conversion and power management applications. The device is intended to support energy storage and current smoothing functions in switching regulator circuits, where stable inductance performance and low power loss are critical. The inductor utilizes a ferrite core construction with a shielded magnetic structure to minimize electromagnetic interference and reduce magnetic flux leakage. This enables improved circuit density and reduced noise coupling in compact electronic assemblies. The design is optimized for use in high current power conversion systems, including buck converters, point-of-load regulators, and distributed power architectures. The component is widely used in industrial, automotive, telecommunications, and embedded systems where reliable energy transfer, thermal stability, and efficient power delivery are required. Its surface mount form factor supports automated PCB assembly and compact system integration while maintaining mechanical robustness under thermal and electrical stress. The design emphasizes low direct current resistance, high current handling capability, and stable inductance behavior under load conditions. It is suitable for applications requiring efficient power conversion with minimal energy loss and stable electromagnetic performance. ## Functional Requirements ### Energy Storage The device shall store energy in a magnetic field during switching operation in power conversion circuits. ### Current Filtering The device shall smooth current ripple in switching regulator applications to maintain stable output conditions. ### Electromagnetic Shielding The device shall reduce electromagnetic interference through a shielded magnetic structure. ### Power Conversion Support The component shall support efficient operation in DC-DC conversion systems. ## Electrical Requirements ### Inductive Performance The device shall provide stable inductance characteristics suitable for power conversion and filtering applications. ### Low Loss Operation The inductor shall minimize resistive and core losses to improve overall system efficiency. ### High Current Capability The device shall support operation under elevated current conditions typical of switching power supplies. ### Thermal Stability The inductor shall maintain performance consistency under thermal loading and temperature variation. ## Mechanical Requirements ### Surface Mount Package The device shall be supplied in a surface mount configuration suitable for automated PCB assembly processes. ### Structural Integrity The component shall withstand mechanical stress during assembly, operation, and thermal cycling. ### PCB Integration The design shall support compact layout integration in multilayer printed circuit board systems. ## Environmental Requirements ### Operating Conditions The device shall operate reliably under conditions typical of industrial and embedded electronic systems. ### Thermal Performance The component shall maintain stable operation under continuous power cycling and heat generation. ### Storage and Handling The device shall retain structural and electrical integrity during storage, transportation, and handling. ## Quality Requirements ### Reliability The inductor shall provide consistent long-term performance under continuous electrical and thermal stress. ### Verification Electrical and thermal characteristics shall be validated through appropriate qualification and testing procedures. ### Compliance The product shall conform to applicable standards for magnetic components used in power electronics applications. ## Documentation Requirements Technical documentation shall include application guidance, layout recommendations for switching power designs, thermal considerations, electrical characteristics, and integration practices for DC-DC converter systems. ## Classification Tags #SRP1038A100M #PowerInductor #ShieldedInductor #SMDInductor #MagneticComponent #EnergyStorageInductor #DCDCConverter #BuckConverter #PowerElectronics #SMPSDesign #ElectromagneticCompatibility #EMIShielding #PCBDesign #ElectricalEngineering #EmbeddedPower #IndustrialElectronics #AutomotiveElectronics #CommonPartsLibrary #ComponentLibrary #EngineeringSpecification #PowerManagement #CircuitDesign #HighCurrentInductor

5.6 nH Unshielded Wirewound Inductor 700 mA 75mOhm Max 0603 (1608 Metric) ## Engineering Specification ## General Description The **0603CS-5N6XJRW** is a Coilcraft **0603CS series ceramic-core chip inductor** designed for RF, microwave, and high-frequency electronic circuit applications. It provides low-value inductance in a compact surface-mount package and is suitable for impedance matching, RF filtering, tuning networks, resonant circuits, oscillators, and general high-frequency signal-path designs. The component is commonly used in wireless modules, communication equipment, RF front-end circuits, test hardware, and compact printed circuit board assemblies requiring stable inductive performance at high frequencies. ## Device Identification Manufacturer Part Number: **0603CS-5N6XJRW** Manufacturer: **Coilcraft** Product Series: **0603CS** Device Category: **Passive Electronic Component** Device Type: **Fixed Inductor** Inductor Type: **RF Chip Inductor** Construction Type: **Unshielded Wirewound Ceramic-Core Inductor** Mounting Type: **Surface Mount** ## Functional Description The device functions as a fixed-value RF inductor used to provide frequency-dependent impedance, energy storage, resonance control, and impedance transformation in electronic circuits. It is designed for high-frequency operation where compact size, low inductance value, and stable RF behavior are required. The component is suitable for use in matching networks, filters, resonant circuits, oscillators, and RF signal conditioning stages. ## Electrical Description The inductor has a nominal inductance of **five point six nanohenries** with **five percent tolerance**. It is rated for **seven hundred milliamps** current and has a maximum DC resistance of **seventy-five milliohms**. The device is intended for RF applications requiring low resistance, high self-resonant frequency, and predictable inductive behavior. It should be operated within the manufacturer’s specified electrical, thermal, and current limits. ## Mechanical Description The component is supplied in an **0603 surface-mount package**, also known as **1608 metric size**. Its compact chip construction supports dense PCB layouts and automated pick-and-place assembly. The unshielded construction is suitable for RF signal applications where board layout, component spacing, and parasitic effects are properly controlled. ## Material and Construction Description The device uses a ceramic-core wirewound construction to support stable high-frequency inductance characteristics. The termination system is designed for standard surface-mount soldering processes and is suitable for compact RF circuit board assemblies. ## Mounting and Assembly Description The **0603CS-5N6XJRW** is intended for surface-mount PCB assembly using standard reflow soldering processes. Proper land pattern design, solder paste control, placement accuracy, and reflow profile should follow Coilcraft recommendations. RF layout practices should be applied, including short trace lengths, controlled impedance routing, minimized parasitic capacitance, and appropriate spacing from nearby conductive or magnetic structures. ## Application Suitability The device is suitable for RF matching networks, antenna tuning, wireless communication circuits, RF filters, resonant circuits, oscillators, broadband RF designs, cellular modules, Wi-Fi and Bluetooth hardware, test equipment, and compact high-frequency embedded electronics. ## Design Considerations The design should account for inductance tolerance, Q factor, self-resonant frequency, DC resistance, current rating, operating temperature, PCB layout parasitics, solder joint reliability, and interaction with nearby components. For RF applications, final performance should be validated in the actual PCB layout because trace geometry, grounding, and component placement can affect impedance and resonance behavior. ## Hashtags #commonpartslibrary #inductor #rfinductor #chipinductor #coilcraft #coilcraftinductor #0603cs #0603component #smdinductor #surfacemount #wirewoundinductor #ceramiccoreinductor #passivecomponent #rfdesign #highfrequency #impedancematching #rffilter #antennatuning #wirelesshardware #communicationequipment #pcbdesign #hardwaredesign #electronicscomponents #electronicparts #componentlibrary #engineeringparts #electronicsengineering

3.9 nH Unshielded Wirewound Inductor 700 mA 80mOhm Max 0603 (1608 Metric) ## Engineering Specification ## General Description The **0603CS-3N9XJRW** is a Coilcraft **0603CS series ceramic-core chip inductor** designed for RF, microwave, and high-frequency circuit applications. It provides low-value inductance in a compact surface-mount package and is suitable for impedance matching, RF filtering, tuning networks, resonant circuits, and general high-frequency signal-path designs. The component is commonly used in wireless modules, RF front-end circuits, communication equipment, test hardware, and compact printed circuit board assemblies requiring stable high-frequency inductive performance. ## Device Identification Manufacturer Part Number: **0603CS-3N9XJRW** Manufacturer: **Coilcraft** Product Series: **0603CS** Device Category: **Passive Electronic Component** Device Type: **Fixed Inductor** Inductor Type: **RF Chip Inductor** Construction Type: **Unshielded Wirewound Ceramic-Core Inductor** Mounting Type: **Surface Mount** ## Functional Description The device functions as a fixed-value RF inductor used to store magnetic energy and provide frequency-dependent impedance in electronic circuits. It is designed for high-frequency performance where low inductance value, compact size, and predictable RF behavior are required. The component can be used in matching networks, RF filters, oscillators, resonant circuits, and signal conditioning paths. ## Electrical Description The inductor has a nominal inductance of **three point nine nanohenries** with **five percent tolerance**. It is rated for **seven hundred milliamps** current and has a maximum DC resistance of **eighty milliohms**. The part provides a minimum self-resonant frequency of **six point nine gigahertz** and a minimum Q value suitable for RF circuit applications. It should be operated within the manufacturer’s specified current, temperature, and electrical limits. ## Mechanical Description The component is supplied in an **0603 surface-mount package**, also known as **1608 metric size**. It is designed for compact PCB layouts and automated pick-and-place assembly. The unshielded chip construction is suitable for high-frequency signal applications where board layout and nearby component placement are carefully controlled. ## Material and Construction Description The device uses a ceramic-core wirewound construction, which supports stable high-frequency inductance characteristics. The specified configuration includes RoHS-compliant matte tin over nickel over silver-platinum-glass frit termination, suitable for standard surface-mount soldering processes. ## Mounting and Assembly Description The **0603CS-3N9XJRW** is intended for surface-mount PCB assembly. Proper land pattern design, solder paste control, placement accuracy, and reflow soldering profile should follow Coilcraft recommendations. RF layout practices should be observed, including short trace lengths, controlled impedance routing, proper grounding, and minimized parasitic capacitance. ## Application Suitability The device is suitable for RF matching networks, wireless communication circuits, antenna tuning, filters, oscillators, resonant circuits, broadband RF designs, cellular modules, Wi-Fi and Bluetooth hardware, test equipment, and high-frequency embedded electronics. ## Design Considerations The design should account for inductance tolerance, Q factor, self-resonant frequency, DC resistance, current rating, operating temperature, layout parasitics, solder joint reliability, and interaction with nearby magnetic or conductive structures. For RF applications, the final performance should be validated in the actual PCB layout because trace geometry and component placement can affect impedance and resonance behavior. ## Hashtags #commonpartslibrary #inductor #rfinductor #chipinductor #coilcraft #coilcraftinductor #0603cs #0603component #smdinductor #surfacemount #wirewoundinductor #ceramiccoreinductor #passivecomponent #rfdesign #highfrequency #impedancematching #rffilter #wirelesshardware #communicationequipment #pcbdesign #hardwaredesign #electronicscomponents #electronicparts #componentlibrary #engineeringparts #electronicsengineering

Bourns SRN3015 Series semi-shielded power inductor, compact 3.0mm × 3.0mm × 1.5mm SMD package, ferrite core construction, inductance range 1.0µH to 100µH, rated current up to 2.35A, saturation current up to 2.35A, low DCR design, operating temperature -40°C to +125°C, RoHS compliant and halogen-free, optimized for DC/DC converters, portable electronics, digital cameras, HDDs, smartphones, LCD displays and compact power management applications. Search Keywords: SRN3015, Bourns SRN3015, SRN3015 power inductor, semi shielded inductor, SMD power inductor, 3x3mm inductor, ferrite inductor, DC DC converter inductor, low profile inductor, SRN3015-1R0Y, SRN3015-2R2M, SRN3015-4R7M, SRN3015-100M, power choke, switching regulator inductor Hashtags: #SRN3015 #BournsSRN3015 #Bourns #PowerInductor #SemiShieldedInductor #SMDInductor #FerriteInductor #DCDCInductor #SwitchingRegulatorInductor #PowerChoke #LowProfileInductor #3x3mmInductor #PortablePower #SMPSInductor #MagneticComponent

Bourns SRP2313CC series shielded power inductor, 2313 package (23mm × 13mm footprint), metal alloy powder core construction, inductance range 0.68µH to 150µH, low DCR, high saturation current up to 90A, operating temperature -40°C to +125°C, magnetically shielded design, optimized for high-current DC/DC converters, VRM power supplies, industrial electronics and automotive power applications. Search Keywords: SRP2313CC, Bourns SRP2313CC, shielded power inductor, metal alloy inductor, high current inductor, DC DC converter inductor, power choke, low DCR inductor, SRP2313CC-R68M, SRP2313CC-1R0M, SRP2313CC-100M, magnetically shielded inductor, VRM inductor, switching regulator inductor Hashtags: #SRP2313CC #BournsSRP2313CC #Bourns #PowerInductor #ShieldedInductor #MetalAlloyInductor #HighCurrentInductor #DCDCInductor #SwitchingRegulatorInductor #PowerChoke #LowDCRInductor #VRMInductor #SMPSInductor #MagneticComponent #Inductor Ind,23.5x22x12.6mm,10uH+/-20%,33A,shd High-current 10 uH shielded power inductor 30-40 A Isat

TDK SPM4030T-1R0M — shielded wound metal SMD power inductor, 1.0 µH ±20%, 4.6 A typ. Isat, 4.0 × 4.2 × 3.0 mm max. Shielded molded power inductor, 4.0mm × 4.0mm × 3.0mm package, metallic magnetic material construction, low DC resistance (DCR), high current capability and low acoustic noise. Suitable for DC/DC converters, VRM circuits, compact power supplies, servers, HDDs and notebook computers. Operating temperature range -40°C to +125°C including self-heating. Для конкретного компонента на скріншоті: SPM4030T-R40M 0.40µH shielded molded power inductor, 4.0×4.0×3.0mm, ±20% tolerance, 4.7mΩ typ DCR, 13.5A rated current (Itemp), 7.8A saturation current (Isat), magnetic shielded construction for high-current switching regulator applications. Search Keywords: SPM4030T-R40M, SPM4030, power inductor, shielded inductor, molded inductor, 0.4uH inductor, 4x4mm power inductor, DC DC converter inductor, low DCR inductor, high current inductor, VRM inductor, SMD power inductor, magnetic shielded inductor Hashtags: #SPM4030TR40M #SPM4030 #PowerInductor #ShieldedInductor #MoldedInductor #SMDInductor #HighCurrentInductor #LowDCRInductor #DCDCConverter #BuckConverter #SwitchingRegulator #VRMInductor #0404Inductor #04uHInductor #MagneticShielded

LED Driver IC 1 Output DC DC Controller SEPIC, Step-Down (Buck), Step-Up (Boost) Analog, PWM Dimming 8-SO-EP # AL8866QSP-13 Engineering Specifications **General Description** The AL8866QSP-13 is an automotive-qualified, multi-topology DC-switching LED controller manufactured by Diodes Incorporated. It is designed to control an external power MOSFET for high-power automotive LED lighting systems. The device supports buck, boost, buck-boost and single-ended primary-inductance converter configurations. Its wide input-voltage range makes it suitable for automotive power systems and various high-voltage LED applications. The controller uses fixed-frequency peak current-mode regulation with spread-spectrum frequency modulation to reduce electromagnetic interference. It supports both analog and pulse-width-modulation dimming through the DIM input. An integrated programmable soft-start function gradually increases the inductor and switching currents during startup to reduce output-voltage and current stress. The open-drain fault output provides system-level fault reporting for abnormal operating conditions. **Engineering Specifications** **Manufacturer:** Diodes Incorporated **Manufacturer Part Number:** AL8866QSP-13 **Component Type:** Automotive LED driver controller **Converter Topologies:** Buck, boost, buck-boost and SEPIC **Control Architecture:** Fixed-frequency peak current-mode control **External Switching Device:** External power MOSFET **Minimum Input Voltage:** Four point seven volts **Maximum Input Voltage:** Eighty-five volts **Maximum Output Voltage:** Eighty-five volts **Switching Frequency:** Four hundred kilohertz **Frequency Modulation:** Spread-spectrum modulation for reduced electromagnetic interference **LED Current Control:** External current-sense resistor and external MOSFET configuration **Feedback Voltage:** Two hundred millivolts **Typical Quiescent Current:** One point eight milliamperes **Typical Efficiency:** Up to approximately ninety-three percent, depending on the application circuit and external components **Dimming Methods:** Analog dimming and pulse-width-modulation dimming **Analog Dimming Range:** One percent to one hundred percent **Analog Dimming Dynamic Range:** Greater than one hundred to one **Pulse-Width-Modulation Dimming Ratio:** One hundred to one at a two-hundred-hertz dimming frequency **Pulse-Width-Modulation Frequency Range:** Approximately one hundred hertz to one kilohertz **Full-Brightness Current Accuracy:** Approximately plus or minus three percent **Low-Level Dimming Current Accuracy:** Approximately plus or minus twelve percent at twenty-percent dimming **Soft-Start Function:** Externally programmable **Fault Output:** Active-low open-drain fault indicator **Protection Features:** Output overvoltage protection, LED open-circuit protection, output undervoltage protection, LED short-circuit protection, cycle-by-cycle overcurrent limitation, current-sense resistor short-circuit protection, inductor and diode short-circuit detection, diode open-circuit protection and thermal shutdown **Automotive Qualification:** AEC-Q100 Grade One qualified **Automotive Documentation:** PPAP capable **Manufacturing Standard:** Manufactured in IATF-certified automotive facilities **Operating Temperature Range:** Minus forty degrees Celsius to positive one hundred twenty-five degrees Celsius **Package Type:** Thermally enhanced SO-8 exposed-pad package **Pin Count:** Eight leads with exposed thermal ground pad **Mounting Style:** Surface mount **Packing Method:** Thirteen-inch tape and reel **Standard Packing Quantity:** Two thousand five hundred components per reel **Moisture Sensitivity:** Level One **Terminal Finish:** Matte-tin-plated leads **Environmental Compliance:** Lead-free, RoHS compliant, halogen-free and antimony-free **Typical Applications** Automotive high-beam and low-beam lighting Automotive daytime running lights Automotive fog lights Automotive turn-signal lights Automotive position lights Automotive brake and stop lights High-power exterior LED lighting Multi-topology automotive LED driver modules #AL8866QSP13 #AL8866Q #DiodesIncorporated #LEDDriver #AutomotiveLED #AutomotiveElectronics #BuckConverter #BoostConverter #BuckBoostConverter #SEPICConverter #PowerElectronics #LEDLighting #ElectronicComponents #EngineeringSpecifications

The TPS6216x device family are easy to use synchronous step-down DC/DC converters optimized for applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCS-Control™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports up to 1-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode). Power sequencing is also possible by configuring the enable and open-drain power good pins. In power save mode, the devices show quiescent current of about 17 μA from VIN. Power save mode, entered automatically and seamlessly if the load is small, maintains high efficiency over the entire load range. In shutdown mode, the device is turned off and shutdown current consumption is less than 2 μA. The device, available in adjustable and fixed output voltage versions, is packaged in an 8-pin WSON package measuring 2.00 mm × 2.00 mm (DSG) or 8- pin VSSOP package measuring 3.00 mm x 3.00 mm (DGK) • DCS-Control™ Topology • Input Voltage Range from 3 V to 17 V • Up to 1-A Output Current • Adjustable Output Voltage From 0.9 V to 6 V • Fixed Output Voltage Versions • Seamless Power Save Mode Transition • Typically 17-µA Quiescent Current • Power Good Output • 100% Duty Cycle Mode • Short Circuit Protection • Over Temperature Protection • Pin to Pin Compatible With TPS62170 and TPS62125 • Available in 3.00 mm x 3.00 mm 8-Pin VSSOP and 2.00 mm × 2.00 mm 8-Pin WSON Packages • Create a Custom Design using the TPS62160 with the WEBENCH® Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Voltage-regulator #switching-regulator

TPS62740DSST WSON-12_L3.0-W2.0-P0.5-BL-EP LCSC Part Number: C2659003 JLCPCB Part Class: Extended Part Manufactured by TI(德州仪器) Texas Instruments TPS62740/TPS62742 ultra-low-power step-down DC/DC converter, 2.2V to 5.5V input voltage range, 360nA typical quiescent current, up to 90% efficiency at 10µA load current, up to 300mA output current for TPS62740 and 400mA for TPS62742, DCS-Control architecture, up to 2MHz switching frequency, 16 selectable output voltages from 1.8V to 3.3V in 100mV steps, power-good output, slew-rate controlled load switch, output discharge function, optimized for 2.2µH inductor and 10µF output capacitor, small 2 x 3mm WSON package, suitable for Bluetooth Low Energy, RF4CE, Zigbee, industrial metering and energy harvesting applications. Search Keywords: TPS62740, TPS62742, Texas Instruments TPS62740, Texas Instruments TPS62742, TI TPS62740, TI TPS62742, TPS6274x buck converter, TPS62740 step down converter, TPS62742 step down converter, ultra low Iq buck converter, 360nA quiescent current converter, low power DC DC converter, energy harvesting buck converter, Bluetooth low energy buck converter, Zigbee power converter, 300mA buck converter, 400mA buck converter, 2x3mm WSON buck converter, TPS62740 datasheet, TPS62742 datasheet Hashtags: #TPS62740 #TPS62742 #TPS6274x #TexasInstrumentsTPS62740 #TexasInstrumentsTPS62742 #TIBuckConverter #StepDownConverter #BuckConverter #DCDCConverter #UltraLowIqConverter #360nAIq #LowPowerConverter #EnergyHarvestingConverter #BluetoothLEConverter #ZigbeeConverter #RF4CEConverter #300mABuckConverter #400mABuckConverter #DCSControl #WSONPackage

DC-DC Controllers LM5176PWPR HTSSOP-28_L9.7-W4.4-P0.65-LS6.4-BL-EP LCSC Part Number: C442493 JLCPCB Part Class: Extended Part Manufactured by TI(德州仪器) Texas Instruments LM5176 synchronous 4-switch buck-boost DC/DC controller, regulates output voltage above, below or equal to input voltage, wide 4.2V to 55V input voltage range with 60V absolute maximum, adjustable 0.8V to 55V output voltage, single-inductor buck-boost architecture, current-mode control, high-efficiency buck-boost transition, adjustable switching frequency with optional synchronization and dithering, integrated 2A MOSFET gate drivers, cycle-by-cycle current limit, optional hiccup protection, input UVLO, soft-start, power-good output, output overvoltage protection, available in HTSSOP-28 and QFN-28 packages. Search Keywords: LM5176, Texas Instruments LM5176, TI LM5176, LM5176 buck boost controller, LM5176 4 switch buck boost, LM5176 synchronous buck boost controller, 55V buck boost controller, 4.2V to 55V DC DC controller, adjustable buck boost controller, single inductor buck boost controller, LM5176 HTSSOP-28, LM5176 QFN-28, LM5176 power supply controller, LM5176 USB power delivery, LM5176 battery powered systems, LM5176 LED lighting, LM5176 datasheet Hashtags: #LM5176 #TexasInstrumentsLM5176 #TIBuckBoostController #BuckBoostController #SynchronousBuckBoost #4SwitchBuckBoost #DCDCController #55VController #SingleInductorBuckBoost #CurrentModeController #MOSFETGateDriver #2AGateDriver #AdjustableFrequencyController #UVLOController #PowerGoodController #OutputOVP #HTSSOP28 #QFN28

WE-MAPI SMT Power Inductor Size 4030; L = 2.2 H +/-20%; IR = 7.1 A; Isat = 9.2 A; RDC = 26 m

Ind,3x3x1mm,10uH+/-20%,1.5A,shd Bourns SRN3012BTA Series semi-shielded SMD power inductor, 0.22µH to 47µH inductance range, ±20% tolerance, high current capability up to 6.2A Irms and 8.0A Isat depending on value, low DCR from 15mΩ typical, ferrite core with magnetic resin coating, enameled copper wire, AEC-Q200 compliant, RoHS compliant and halogen-free, -55°C to +125°C operating temperature, compact 3.0 x 3.0mm automotive-grade surface-mount package, suitable for DC/DC converters and automotive power circuits. Search Keywords: Bourns SRN3012BTA, SRN3012BTA Series, Bourns semi shielded inductor, SRN3012BTA power inductor, automotive SMD inductor, AEC-Q200 power inductor, 3.0x3.0mm power inductor, semi shielded power inductor, Bourns automotive inductor, SRN3012BTA-R22M, SRN3012BTA-1R0M, SRN3012BTA-100M, SRN3012BTA-220M, SRN3012BTA-470M, ferrite core SMD inductor, magnetic resin coated inductor 10uH shielded inductor <=1.0mm >=1.5A <=150mΊ Hashtags: #BournsSRN3012BTA #SRN3012BTA #BournsInductor #PowerInductor #SMDInductor #SemiShieldedInductor #AutomotiveInductor #AECQ200Inductor #FerriteCoreInductor #WirewoundInductor #MagneticResinInductor #DCDCInductor #HighCurrentInductor #LowDCRInductor #3x3mmInductor #SRN3012BTAR22M #SRN3012BTA100M #SRN3012BTA470M

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 500mA 8-WFDFN Exposed Pad The TPS6217x device family are easy to use synchronous step-down DC-DC converters optimized for applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCS-Control™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports up to 0.5-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode). Power sequencing is also possible by configuring the enable and open-drain power good pins. In power save mode, the devices show quiescent current of about 17 μA from VIN. Power save mode, entered automatically and seamlessly if the load is small, maintains high efficiency over the entire load range. In shutdown mode, the device is turned off and shutdown current consumption is less than 2 μA. The device, available in adjustable and fixed output voltage versions, is packaged in a 2-mm × 2-mm 8- pin WSON package (DSG). • DCS-Control™ Topology • Input Voltage Range from 3 V to 17 V • Up to 500-mA Output Current • Adjustable Output Voltage from 0.9 V to 6 V • Fixed Output Voltage Versions • Seamless Power Save Mode Transition • Typically 17-µA Quiescent Current • Power Good Output • 100% Duty Cycle Mode • Short Circuit Protection • Over Temperature Protection • Pin to Pin Compatible with TPS62160 and TPS62125 • Available in a 2-mm × 2-mm 8-Pin WSON Package • Create a Custom Design using the TPS62170 with the WEBENCH® Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement

Abracon AISC-0402HP Series high-current ceramic wire wound SMD RF inductor, 0402 package, 1.00 x 0.55 x 0.50mm size, inductance range from 2.0nH to 68nH, high Q factor, low DCR, high self-resonant frequency up to 8.5GHz, rated current up to 2100mA, ±2%, ±5% or ±10% tolerance options, -40°C to +125°C operating temperature, RoHS/RoHS II compliant, suitable for RF circuits, Bluetooth, WLAN, GPS, broadband network and wireless communication applications. Search Keywords: AISC-0402HP, Abracon AISC-0402HP, AISC-0402HP Series, Abracon 0402 inductor, 0402 ceramic wire wound inductor, high current 0402 inductor, RF chip inductor 0402, ceramic RF inductor, wire wound RF inductor, high Q 0402 inductor, low DCR 0402 inductor, SMD RF inductor, 2nH to 68nH inductor, Bluetooth RF inductor, WLAN RF inductor, GPS RF inductor, AISC-0402HP datasheet Hashtags: #AISC0402HP #AbraconAISC0402HP #AbraconInductor #0402Inductor #SMDInductor #RFInductor #CeramicInductor #WireWoundInductor #HighCurrentInductor #HighQInductor #LowDCRInductor #ChipInductor #BluetoothInductor #WLANInductor #GPSInductor #WirelessInductor #RFCircuitInductor #2nHInductor #68nHInductor 0402HP-25 0402HP

Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 1A 8-WFDFN Exposed Pad The TPS6216x device family are easy to use synchronous step-down DC/DC converters optimized for applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCS-Control™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports up to 1-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode). Power sequencing is also possible by configuring the enable and open-drain power good pins. In power save mode, the devices show quiescent current of about 17 μA from VIN. Power save mode, entered automatically and seamlessly if the load is small, maintains high efficiency over the entire load range. In shutdown mode, the device is turned off and shutdown current consumption is less than 2 μA. The device, available in adjustable and fixed output voltage versions, is packaged in an 8-pin WSON package measuring 2.00 mm × 2.00 mm (DSG) or 8- pin VSSOP package measuring 3.00 mm x 3.00 mm (DGK). • DCS-Control™ Topology • Input Voltage Range from 3 V to 17 V • Up to 1-A Output Current • Adjustable Output Voltage From 0.9 V to 6 V • Fixed Output Voltage Versions • Seamless Power Save Mode Transition • Typically 17-µA Quiescent Current • Power Good Output • 100% Duty Cycle Mode • Short Circuit Protection • Over Temperature Protection • Pin to Pin Compatible With TPS62170 and TPS62125 • Available in 3.00 mm x 3.00 mm 8-Pin VSSOP and 2.00 mm × 2.00 mm 8-Pin WSON Packages • Create a Custom Design using the TPS62160 with the WEBENCH® Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement

TDK SPM7054VT-150M-D shielded wirewound power inductor, 15µH inductance, ±20% tolerance, 4.5A temperature-rise current, 5.0A saturation current at 20% inductance drop, 54.8mΩ typical DC resistance, metal composite magnetic core, AEC-Q200 qualified, -55°C to +155°C operating temperature, vibration resistant up to 30G, compact 7.5 x 7.0 x 6.4mm SMD package, suitable for automotive power circuits, LED, ECM, ADAS and BCM applications. Search Keywords: SPM7054VT-150M-D, TDK SPM7054VT-150M-D, SPM7054VT 150M, SPM7054VT-150M, TDK 15uH inductor, 15uH shielded inductor, 15uH power inductor 4.5A, 15uH 54.8mOhm inductor, metal composite inductor, automotive power inductor, AEC-Q200 inductor, SPM7054VT series, TDK SPM7054VT, shielded wirewound inductor, SMD power inductor 7054 Hashtags: #SPM7054VT150MD #SPM7054VT #TDKSPM7054VT #TDKInductor #15uHInductor #PowerInductor #ShieldedInductor #WirewoundInductor #MetalCompositeInductor #SMDInductor #AutomotiveInductor #AECQ200Inductor #4A5Inductor #54mOhmInductor #7054Inductor #ECMInductor #ADASInductor #BCMInductor20200702 Manufacturer Recommendations 5.4 mm TDK

18µH Unshielded Wirewound Inductor 1.89 A 100mOhm Max Nonstandard The RLS-186-R is a surface-mount line inductor manufactured by RECOM. It is designed for use in power supply filtering and EMI suppression applications, especially in DC/DC converter circuits and switching power supplies. The component provides stable inductance performance, low DC resistance, and reliable operation in compact electronic designs. Key Features 18 µH inductance value Surface-mount (SMD) package Low DC resistance for improved efficiency Suitable for power line filtering and noise suppression Compact size for space-saving PCB layouts High operating temperature range RoHS compliant Tape-and-reel packaging (“-R” suffix) Tested for use in RECOM filter and power supply designs #commonpartslibrary #inductor #coil

Non-Isolated PoL Module DC DC Converter 1 Output 1.2 ~ 6V 2.5A 4.5V - 28V Input The RPX-2.5-R is a compact non-isolated buck DC/DC converter module from RECOM Power designed for point-of-load (PoL) power regulation in embedded, industrial, IoT, and portable electronic applications. It integrates a shielded inductor and switching regulator inside a tiny thermally enhanced QFN package, enabling high efficiency and simplified PCB design. Key Features Wide input voltage range: 4.5V to 28V DC Adjustable output voltage: 1.2V to 6V DC Maximum output current: 2.5A High efficiency up to 91% Integrated shielded inductor for reduced EMI Compact low-profile QFN package: approximately 4.5mm × 4mm × 2mm Supports 5V, 12V, and 24V supply systems Built-in protections: Short-circuit protection (SCP) Overcurrent protection (OCP) Overtemperature protection (OTP) Overvoltage protection (OVP) Undervoltage lockout (UVLO) Enable/control pin for power sequencing and shutdown Flip-chip thermal technology for improved heat dissipation Suitable for SMT automated assembly applications Typical Applications Industrial automation systems IoT devices Embedded control boards Medical and imaging equipment Battery-powered systems Telecom and sensor modules Space-constrained power designs

Non-Isolated PoL Module DC DC Converter 1 Output 1 ~ 36V 12A 5V - 36V Input The LTM®4712 is a high efficiency buck-boost µModule® (micromodule) regulator. The switching controller, power switches, inductor and support components are included in the package. The complete design requires only a few external components, including a resistor to set frequency, a resistor to set output voltage, input, and output capacitors, a sensing resistor to achieve input or output average current regulation. The LTM4712 operates over a 5V to 36V input voltage range and can regulate output voltages between 1V and 36V. The LTM4712 supports selectable forced continuous mode (FCM)/pulse-skipping mode (PSM) operation. The current mode control enables a fast transient response to line and load changes without sacrificing stability. The SYNC input and CLKOUT output allow easy synchronization. It supports multi-phase parallel operation for high power applications. The LTM4712 is offered in a 16mm × 16mm × 8.34mm ball grid array (BGA) package suitable for automated assembly by standard surface mount equipment. The LTM4712 is RoHS-compliant. #Power-supply #DCDC-Converter