Switches
A switch is a device that allows electricity to flow through a circuit by completing or interrupting the connection. It is a common component in electrical and electronic systems and is used in a variety of applications, such as controlling the flow of electricity in a circuit, turning devices on and off, and routing electrical signals. One of the primary use cases for switches is to control the flow of electricity in a circuit. This can be done by manually flipping the switch or by using a control mechanism, such as a timer or a sensor. Another common use for switches is to turn devices on and off. This can be done using a switch that is built into the device or by using a separate switch that is connected to the device. In addition to these basic use cases, switches can also be used to route electrical signals. For example, a switch can be used to route a signal from one device to another or to direct a signal to a specific circuit or component. If you're looking for a wide variety of switches for your projects, flux.ai has the world's largest community-driven public library of them. The library includes footprints, symbols, datasheets, and simulation models for a wide range of switches, making it easy to find the right switch for your needs.
LM5146QRGYRQ1
DC-DC Controllers LM5146QRGYRQ1 VQFN-20_L4.5-W3.5-P0.50-BL-EP-1 LCSC Part Number: C1850329 JLCPCB Part Class: Extended Part Manufactured by TI(德州仪器) Texas Instruments LM5146-Q1 100V synchronous buck DC/DC controller for automotive applications, AEC-Q100 Grade 1 qualified, 5.5V to 100V wide input voltage range, adjustable output voltage from 0.8V to 60V, 150°C maximum junction temperature, 100% duty cycle operation during input voltage dips, 40ns minimum high-side on-time, 140ns minimum off-time, switching frequency from 100kHz to 1MHz with synchronization capability, 7.5V gate drivers for standard VTH MOSFETs, 2.3A source and 3.5A sink gate drive capability, lossless RDS(on) or shunt current sensing, adjustable soft-start, hiccup overcurrent protection, UVLO, PGOOD indicator, thermal shutdown, 20-pin VQFN package. Search Keywords: LM5146-Q1, Texas Instruments LM5146-Q1, TI LM5146-Q1, LM5146 automotive buck controller, 100V synchronous buck controller, AEC-Q100 buck controller, LM5146-Q1 VQFN-20, wide input buck controller, 5.5V to 100V buck controller, 0.8V to 60V output controller, 48V automotive buck controller, HEV EV buck controller, ADAS buck controller, LM5146-Q1 datasheet Hashtags: #LM5146Q1 #TexasInstrumentsLM5146Q1 #TIBuckController #SynchronousBuckController #100VBuckController #AutomotiveBuckController #AECQ100 #WideInputController #48VAutomotive #HEVPowerSupply #EVPowerSupply #ADASPower #MOSFETGateDriver #CurrentModeController #VQFN20
64 Uses0 StarsAO3401
MOSFET P-CH 30V 4.1A SOT-23 The AO3401 is a 30 V P-Channel Enhancement Mode MOSFET designed for high-efficiency power switching applications. It uses advanced trench MOSFET technology to achieve low on-resistance (RDS(on)), low gate charge, and fast switching performance. Packaged in a compact SOT-23 package, it is widely used in load switching, battery-powered devices, reverse-polarity protection circuits, and power management applications. Key Features P-Channel MOSFET Drain-Source Voltage (VDS): −30 V Continuous Drain Current (ID): up to −4 A (25°C) Low RDS(on): 50 mΩ max @ VGS = −10 V 60 mΩ max @ VGS = −4.5 V 85 mΩ max @ VGS = −2.5 V Low Gate Charge: 7 nC typical @ 4.5 V Gate-Source Voltage Rating: ±12 V Low Threshold Voltage: −0.5 V to −1.3 V Fast Switching Characteristics Compact SOT-23 Surface-Mount Package Operating Junction Temperature: up to 150°C Suitable for Low-Voltage Logic-Level Drive Applications Typical Applications Load switches Battery protection circuits Reverse-polarity protection Power-path management DC-DC converters Portable and battery-powered electronics PWM switching applications #CommonPartsLibrary #Transistor #FET #Mosfet
27 Uses0 StarsAMS1117-3.3RG
The AMS1117-3.3RG is a fixed-output, low-dropout (LDO) linear voltage regulator that provides a regulated 3.3 V output from a higher input voltage. It is capable of delivering up to 1 A output current and is commonly used in microcontroller, communication, and embedded-system power supplies where a stable 3.3 V rail is required. The device includes built-in protection features such as current limiting and thermal shutdown for improved reliability. Key Features Fixed 3.3 V output voltage Supports up to 1 A output current Low dropout voltage, typically around 1.2 V and up to 1.3 V at 1 A load Input voltage capability up to 12 V (some manufacturer variants specify higher absolute maximum ratings) Good line and load regulation Built-in current limiting protection Built-in thermal shutdown protection Available in SOT-223 surface-mount package Suitable for post-regulation of switching power supplies and general 3.3 V power conversion applications Typical Applications ESP32, STM32, and other microcontroller-based systems Embedded and IoT devices Communication modules LCD monitors and display circuits Battery-powered equipment Post-regulation for DC/DC converters Motherboards and expansion cards #CommonPartsLibrary #IntegratedCircuit #PowerManagement #LDO
140 Uses0 StarsTPS62160DSGT
The TPS6216x device family are easy to use synchronous step-down DC/DC converters optimized for applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCS-Control™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports up to 1-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode). Power sequencing is also possible by configuring the enable and open-drain power good pins. In power save mode, the devices show quiescent current of about 17 μA from VIN. Power save mode, entered automatically and seamlessly if the load is small, maintains high efficiency over the entire load range. In shutdown mode, the device is turned off and shutdown current consumption is less than 2 μA. The device, available in adjustable and fixed output voltage versions, is packaged in an 8-pin WSON package measuring 2.00 mm × 2.00 mm (DSG) or 8- pin VSSOP package measuring 3.00 mm x 3.00 mm (DGK) • DCS-Control™ Topology • Input Voltage Range from 3 V to 17 V • Up to 1-A Output Current • Adjustable Output Voltage From 0.9 V to 6 V • Fixed Output Voltage Versions • Seamless Power Save Mode Transition • Typically 17-µA Quiescent Current • Power Good Output • 100% Duty Cycle Mode • Short Circuit Protection • Over Temperature Protection • Pin to Pin Compatible With TPS62170 and TPS62125 • Available in 3.00 mm x 3.00 mm 8-Pin VSSOP and 2.00 mm × 2.00 mm 8-Pin WSON Packages • Create a Custom Design using the TPS62160 with the WEBENCH® Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Voltage-regulator #switching-regulator
34 Uses0 StarsTC4427EOA
TC4427EOA SOIC-8_L4.9-W3.9-P1.27-LS6.0-TR LCSC Part Number: C636891 JLCPCB Part Class: Extended Part Manufactured by MICROCHIP(美国微芯) Microchip TC4426 dual high-speed MOSFET gate driver, 1.5A peak source/sink output current, 4.5V to 18V supply voltage range, matched rise and fall times, 25ns typical rise/fall time with 1000pF load, 40ns typical propagation delay, 7Ω output impedance, latch-up protected, withstands ±500mA reverse output current, accepts negative input swings up to 5V, ESD protected to 2kV, designed for driving power MOSFETs, SMPS, pulse transformers and line drivers, available in SOIC-8, PDIP-8, MSOP-8 and DFN-8 packages. Search Keywords: TC4426, TC4426CPA, TC4426COA, TC4426A, Microchip TC4426, MOSFET gate driver, dual MOSFET driver, 1.5A gate driver, high speed MOSFET driver, power MOSFET driver, gate driver IC, low side MOSFET driver, SMPS gate driver, pulse transformer driver, TC4426 SOIC-8, TC4426 DFN-8, TC4426 MSOP-8, TC4426 PDIP-8 Hashtags: #TC4426 #MicrochipTC4426 #MOSFETDriver #GateDriver #DualMOSFETDriver #15AGateDriver #PowerMOSFETDriver #HighSpeedGateDriver #LowSideDriver #SMPSDriver #PulseTransformerDriver #LineDriver #SOIC8 #MSOP8 #DFN8 #PDIP8 #Microchip #GateDriverIC #PowerElectronics #SwitchModePowerSupply
17 Uses0 StarsBTA16-600BQ
TRIACs BTA16-600BQ TO-220-3_L10.2-W4.5-P2.54-L-1 LCSC Part Number: C602638 JLCPCB Part Class: Extended Part Manufactured by WeEn(瑞能) WeEn BTA16-600B planar passivated 4-quadrant triac, 600V class bidirectional AC switching device, internally insulated SOT78D / IITO-220 plastic package, high voltage capability, high junction operating temperature up to 150°C, least sensitive gate for high noise immunity, triggering in all four quadrants, isolated mounting base with 2500V RMS isolation, suitable for general-purpose switching, phase control, compressor starting circuits and motor control applications. Search Keywords: BTA16-600B, WeEn BTA16-600B, BTA16 600B triac, 4Q triac, 4 quadrant triac, 600V triac, insulated triac, SOT78D triac, IITO-220 triac, phase control triac, AC switching triac, motor control triac, compressor starting triac, BTA16-600B datasheet Hashtags: #BTA16600B #WeEnBTA16600B #WeEnTriac #Triac #4QTriac #4QuadrantTriac #600VTriac #ACTriac #BidirectionalSwitch #PhaseControlTriac #MotorControlTriac #CompressorStartTriac #SOT78D #IITO220 #InsulatedTriac
72 Uses0 StarsBQ25798RQMR
BQ25798RQMR QFN-29_L4.0-W4.0-P0.40-TL-BQ25792RQMR LCSC Part Number: C2876593 JLCPCB Part Class: Extended Part Manufactured by TI(德州仪器) Texas Instruments BQ25798 fully integrated switch-mode buck-boost battery charger for 1-4 cell Li-ion and Li-polymer batteries, supports USB PD 3.0 power profile, integrates four switching MOSFETs, BATFET, input and charging current sensing, 3.6V to 24V input operating range with 30V absolute maximum, 750kHz or 1.5MHz switching frequency, up to 5A charging current with 10mA resolution, up to 96.5% efficiency, supports MPPT for photovoltaic charging, USB BC1.2/HVDCP/non-standard adapter detection, NVDC power path management, USB OTG output from 2.8V to 22V up to 3.32A, I2C control, integrated 16-bit ADC, low quiescent current, thermal regulation, OVP/OCP protection, safety timer, 29-pin 4x4mm QFN package. Search Keywords: BQ25798, Texas Instruments BQ25798, TI BQ25798, BQ25798 battery charger, BQ25798 buck boost charger, BQ25798 Li-ion charger, BQ25798 Li-polymer charger, 1-4 cell battery charger, USB PD 3.0 battery charger, buck boost charger IC, NVDC power path charger, MPPT battery charger IC, photovoltaic battery charger, USB OTG charger IC, 5A charging current charger, I2C battery charger, BQ25798 QFN-29, 4x4mm QFN charger, BQ25798 datasheet Hashtags: #BQ25798 #TexasInstrumentsBQ25798 #TIBatteryCharger #BatteryChargerIC #BuckBoostCharger #LiIonCharger #LiPolymerCharger #1to4CellCharger #USBPDCharger #USBPD30 #NVDCCharger #PowerPathManagement #MPPTCharger #PhotovoltaicCharger #USBOTGCharger #5ACharger #I2CCharger #IntegratedADC #QFN29 #4x4mmQFN
57 Uses0 Stars
