Voltage Regulators
A voltage regulator is an electronic device that maintains a constant output voltage level, regardless of changes in the input voltage or load conditions. These devices are commonly used to provide a stable power supply to electronic circuits, as well as to protect them from voltage spikes and surges. There are several types of voltage regulators, including linear, switching, and pulse width modulation (PWM) regulators, each with its own set of characteristics and applications. Linear regulators, for example, are simple and efficient, but have a relatively low switching speed and can only provide a limited output current. Switching regulators, on the other hand, have higher switching speeds and can provide a higher output current, but are more complex and require additional components. In addition to their use in power supplies and voltage protection, voltage regulators are also used in a wide range of other applications, including motor control, battery charging, and instrumentation. Flux.ai has the world's largest community-driven public library of voltage regulators, with footprints, symbols, datasheets, and simulation models for a wide range of devices. Whether you're a designer, engineer, or hobbyist, you can find the resources you need to get your project up and running quickly and efficiently.
CP2102N-A02-GQFN24
USB-to-UART Bridge CP2102N-A02-GQFN24 is a highly integrated USB-to-UART bridge controller from Silicon Labs. It provides a simple and cost-effective way to add USB connectivity to embedded systems by converting USB 2.0 Full-Speed communication into a standard UART interface. The device integrates the USB transceiver, oscillator, voltage regulator, and UART controller, minimizing external components and eliminating the need for USB firmware development. It is commonly used in microcontroller programming interfaces, industrial equipment, POS terminals, data loggers, and USB-to-serial adapters. Key Features USB 2.0 Full-Speed compliant (12 Mbps) interface. USB-to-UART bridge with data rates up to 3 Mbaud. Integrated USB transceiver; no external USB resistors required. Integrated oscillator; no external crystal required. On-chip 3.3 V voltage regulator. USB Battery Charger Detection (BC 1.2) support. Remote wakeup capability from USB suspend state. Low operating current of approximately 9.5 mA. Hardware and software flow control support. Internal configurable ROM for Vendor ID, Product ID, serial number, and USB descriptors. Royalty-free Virtual COM Port (VCP) drivers available for major operating systems. Operating temperature range: −40°C to +85°C. Compact 24-pin QFN (4 mm × 4 mm) package. Typical Applications USB-to-Serial adapters Microcontroller programming and debugging interfaces Industrial automation equipment Point-of-sale (POS) terminals Medical instruments Data acquisition and logging systems Embedded systems requiring USB connectivity #commonpartslibrary #integratedcircuit
203 Uses0 StarsB0505S-1WR3
The B0505S-1WR3 is a compact isolated DC-DC power converter module designed to provide regulated power conversion while maintaining galvanic isolation between input and output circuits. The module incorporates high-frequency switching technology and transformer isolation to deliver stable power with reduced noise coupling and improved system safety. It is widely used in industrial control systems, communication equipment, instrumentation, data acquisition devices, medical electronics, and embedded applications where isolated power rails are required to eliminate ground loops and enhance signal integrity. Engineering Specification Device Type Isolated DC-DC Converter Module Power Conversion Topology Transformer-Isolated Switching Regulator Input Configuration Single DC Input Output Configuration Single Isolated DC Output Isolation Method Internal High-Frequency Transformer Isolation Regulation Characteristics Regulated Output Voltage High Conversion Efficiency Low Output Ripple and Noise Electrical Features Galvanic Isolation Between Input and Output Enhanced Noise Immunity Stable Load Regulation Reliable Power Transfer Performance Protection Characteristics Short-Circuit Resistant Design Input-to-Output Isolation Protection Thermal Reliability Enhancement Package Style Single In-Line Through-Hole Package Mounting Type Through-Hole Mounting Environmental Characteristics Industrial-Grade Reliability Long Operational Lifetime High Resistance to Electrical Interference Suitable for Harsh Operating Environments Applications Industrial Automation Equipment Data Acquisition Systems Sensor Signal Conditioning Communication Interfaces Medical Electronics Embedded Control Systems Power Supply Isolation Instrumentation Equipment Process Control Devices Microcontroller-Based Systems Features Compact Integrated Module Isolated Power Distribution High Reliability Design Low Electromagnetic Interference Simple Circuit Integration Efficient Power Conversion Stable Output Performance Wide Application Compatibility RoHS Compliant Construction Manufacturer MORNSUN #commonpartslibrary #powermodule #dcdcconverter #isolatedpower #galvanicisolation #powermanagement #powersupply #powerelectronics #industrialelectronics #instrumentation #communications #embeddedsystems #medicalelectronics #throughhole #electroniccomponents
91 Uses0 StarsTPS54336ADRCR
Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 3A 10-VFDFN Exposed Pad The TPS5433xA family of devices are synchronous converters with an input-voltage range of 4.5 V to 28 V. These devices include This device has an integrated low-side switching FET that eliminates the need for an external diode which reduces component count. Efficiency is maximized through the integrated 128- mΩ and 84-mΩ MOSFETs, low IQ and pulse skipping at light loads. Using the enable pin, the shutdown supply current is reduced to 2 μA. This step-down (buck) converter provides accurate regulation for a variety of loads with a well-regulated voltage reference that is 1.5% over temperature. Cycle-by-cycle current limiting on the high-side MOSFET protects the TPS5433xA family of devices in overload situations and is enhanced by a low-side sourcing current limit which prevents current runaway. A low-side sinking current-limit turns off the low-side MOSFET to prevent excessive reverse current. Hiccup protection is triggered if the overcurrent condition continues for longer than the preset time. Thermal shutdown disables the device when the die temperature exceeds the threshold and enables the device again after the built-in thermal hiccup time. • Synchronous 128-mΩ and 84-mΩ MOSFETs for 3-A Continuous Output Current • TPS54335A: Internal 2-ms Soft-Start, 50-kHz to 1.5-MHz Adjustable Frequency • TPS54336A: Adjustable Soft-Start, Fixed 340-kHz Frequency • Low 2-µA Shutdown, Quiescent Current • 0.8-V Voltage Reference with ±0.8% Accuracy • Current Mode Control • Monotonic Startup into Pre-Biased Outputs • Pulse Skipping for Light-Load Efficiency • Hiccup Mode Overcurrent Protection • Thermal Shutdown (TSD) and Overvoltage Transition Protection • 8-Pin SO PowerPAD™ and 10-Pin VSON Package • Create a Custom Design Using the TPS54335A with the WEBENCH Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement
128 Uses0 StarsTPS62162DSGT
Buck Switching Regulator IC Positive Fixed 3.3V 1 Output 1A 8-WFDFN Exposed Pad The TPS6216x device family are easy to use synchronous step-down DC/DC converters optimized for applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCS-Control™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports up to 1-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode). Power sequencing is also possible by configuring the enable and open-drain power good pins. In power save mode, the devices show quiescent current of about 17 μA from VIN. Power save mode, entered automatically and seamlessly if the load is small, maintains high efficiency over the entire load range. In shutdown mode, the device is turned off and shutdown current consumption is less than 2 μA. The device, available in adjustable and fixed output voltage versions, is packaged in an 8-pin WSON package measuring 2.00 mm × 2.00 mm (DSG) or 8- pin VSSOP package measuring 3.00 mm x 3.00 mm (DGK). • DCS-Control™ Topology • Input Voltage Range from 3 V to 17 V • Up to 1-A Output Current • Adjustable Output Voltage From 0.9 V to 6 V • Fixed Output Voltage Versions • Seamless Power Save Mode Transition • Typically 17-µA Quiescent Current • Power Good Output • 100% Duty Cycle Mode • Short Circuit Protection • Over Temperature Protection • Pin to Pin Compatible With TPS62170 and TPS62125 • Available in 3.00 mm x 3.00 mm 8-Pin VSSOP and 2.00 mm × 2.00 mm 8-Pin WSON Packages • Create a Custom Design using the TPS62160 with the WEBENCH® Power Designer #CommonPartsLibrary #IntegratedCircuit #PowerManagement
243 Uses0 Stars
