Bluetooth, WiFi 802.11b/g/n, Bluetooth v5.0 Transceiver Module 2.4GHz PCB Trace Surface Mount The ESP32-C3-WROOM-02-N4 is a compact, general-purpose Wi-Fi and Bluetooth Low Energy (BLE) module developed by Espressif Systems. It is built around the ESP32-C3 SoC and integrates RF components, crystal oscillator, flash memory, and PCB antenna in a single module. It is designed for a wide range of applications such as IoT devices, smart home systems, industrial automation, and consumer electronics, offering a balance of performance, low power consumption, and cost efficiency. Key Features MCU & Memory 32-bit RISC-V single-core processor up to 160 MHz 384 KB ROM 400 KB SRAM + 8 KB RTC SRAM Integrated 4 MB SPI flash (N4 variant) Connectivity 2.4 GHz Wi-Fi (802.11 b/g/n) Supports Station, SoftAP, and Station + SoftAP modes Bluetooth 5 (BLE) with mesh support Data rates up to 150 Mbps (Wi-Fi) Peripherals & Interfaces Up to 15 GPIOs Interfaces: SPI, UART, I2C, I2S LED PWM ADC (SAR) Timers & watchdog USB Serial/JTAG support TWAI® (CAN 2.0 compatible) #commonpartslibrary #transceiver #module #wireless #rf

WS2812 is a intelligent control LED light source that the control circuit and RGB chip are integrated in a package of 5050 components. #CommonPartsLibrary #LED

RP2040 chip for Raspberry Pi Pico - ARM® Cortex®-M0+ MCU 32-Bit The RP2040 is a high-performance, low-cost microcontroller built around two ARM Cortex-M0+ cores. It is optimized for flexibility, ease of use, and deterministic real-time performance. Unlike many microcontrollers, it includes a unique programmable I/O subsystem (PIO), allowing custom hardware interfaces without extra components. Key Features Processing Dual-core ARM Cortex-M0+ processors Up to 133 MHz clock speed Efficient integer performance with low power consumption Memory 264 KB on-chip SRAM External QSPI flash support (typically 2 MB–16 MB depending on board) Programmable I/O (PIO) 2 PIO blocks, each with 4 state machines Enables custom protocols (e.g., SPI, I2C, UART, WS2812, VGA, etc.) Offloads timing-critical tasks from CPU 🔗 Connectivity Interfaces 2× UART 2× SPI 2× I2C USB 1.1 controller (device or host support) 16× PWM channels Analog Features 12-bit ADC (up to 5 channels, including internal temperature sensor) Power & Voltage Operating voltage: 1.8V – 3.3V Low-power modes available Package Options QFN-56 (7×7 mm) Development Ecosystem Supports C/C++ SDK MicroPython and CircuitPython support Strong community and documentation Typical Applications Embedded systems and IoT devices Robotics and automation DIY electronics and prototyping USB devices (HID, MIDI, etc.) Custom communication interfaces using PIO #CommonPartsLibrary #IntegratedCircuit #Microcontroller

Polymeric PTC Resettable Fuse 60V 500 mA Ih Surface Mount 2-SMD 500mA resettable fuse pptc The SMD050F-2 is a surface-mount resettable fuse (PPTC – Polymer Positive Temperature Coefficient) designed to provide overcurrent protection in low-voltage electronic circuits. It operates by increasing its resistance significantly when excessive current flows, thereby limiting current and protecting downstream components. Once the fault condition is removed and the device cools, it automatically resets to its low-resistance state, enabling normal operation without replacement. This component is commonly used in power supply lines, USB ports, battery-powered devices, and general electronic protection applications where space-saving and reliability are important. Key Features Resettable overcurrent protection (self-recovering) Surface-mount package for compact PCB layouts Low resistance in normal operation Fast response to fault conditions Automatic reset after fault removal RoHS compliant and lead-free Electrical Characteristics Hold current: 0.5 A Trip current: 1.0 A (typical) Maximum voltage: 60 V Maximum current: 40 A (fault current rating) Initial resistance: low resistance range suitable for minimal voltage drop Resistance after trip: significantly increased to limit current Thermal Characteristics Operating temperature range: -40°C to +85°C Trip time dependent on applied current and ambient temperature Reset time dependent on cooling conditions Mechanical Characteristics Package type: Surface-mount (SMD) Compact footprint suitable for dense PCB layouts Compatible with standard reflow soldering processes Applications USB and peripheral port protection Power supply and DC line protection Battery pack protection Consumer electronics Industrial control circuits Compliance and Standards RoHS compliant Halogen-free (depending on manufacturer variant) Meets industry standards for resettable fuses #commonpartslibrary #circuitprotection #ptc #fuse

Buck Switching Regulator IC Positive Fixed 5V 1 Output 1A SOT-23-6 The LMR50410Y5FQDBVRQ1 (part of the LMR50410-Q1 family from Texas Instruments) is a synchronous step-down (buck) DC-DC converter designed for automotive and industrial power applications. It operates over a wide input voltage range of 4 V to 36 V and can deliver up to 1 A output current, making it suitable for converting higher, unregulated voltages into stable lower voltages (e.g., 5 V or 3.3 V rails). The device integrates power switches, control circuitry, and compensation internally, allowing simple design with minimal external components and a compact PCB footprint. Key Features Power & Performance Wide input voltage range: 4 V to 36 V Output current: up to 1 A High switching frequency: 2.1 MHz (enables small inductors) High efficiency with PFM (light load) and FPWM (constant frequency) options Integration & Ease of Use Synchronous rectification (integrated high-side & low-side MOSFETs) Internal compensation (no complex external tuning) Minimal external components required Small SOT-23-6 package for compact designs Protection & Reliability Cycle-by-cycle current limit Short-circuit protection (hiccup mode) Thermal shutdown protection Undervoltage lockout (UVLO) ±1% reference voltage accuracy Automotive & Industrial Capability AEC-Q100 qualified (automotive grade) Operating temperature: Ambient: up to 125°C Junction: up to 150°C Designed for rugged automotive environments Additional Features Soft-start for controlled startup Precision enable pin for system control Monotonic startup with pre-biased output Available in fixed output (e.g., 5 V) variants Typical Applications Automotive electronics (ADAS, infotainment, lighting) Industrial power supplies Distributed power systems General-purpose DC-DC regulation #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

Connector Header Through Hole 5 position 0.100" (2.54mm) SWD header 1x5 2.54mm PinHeader 1x05 2.54mm horizontal The TSW-105-07-G-S is a high-reliability, through-hole, single-row pin header from Samtec’s TSW series. It is designed for board-to-board or wire-to-board interconnections in a wide range of electronic applications. Featuring a standard 2.54 mm pitch and gold-plated contacts, this connector ensures reliable electrical performance, durability, and compatibility with industry-standard mating components. Mechanical Characteristics Connector Type: Pin Header Mounting Type: Through-Hole Number of Positions: 5 Number of Rows: Single Row Pitch: 2.54 mm Orientation: Vertical Termination Style: Solder Contact Shape: Square Post Material and Plating Contact Material: Phosphor Bronze Contact Plating: Gold over Nickel Housing Material: Black Thermoplastic (UL94 V-0 rated) Electrical Characteristics Current Rating: Typically up to 3 A per contact Voltage Rating: Typically up to 500 VAC Contact Resistance: Low contact resistance for reliable signal transmission Insulation Resistance: High insulation resistance Environmental Characteristics Operating Temperature Range: -55°C to +125°C Flammability Rating: UL94 V-0 Applications Board-to-board connections Wire-to-board interfaces Prototyping and development systems Industrial and consumer electronics Compliance and Standards RoHS Compliant Lead-Free #CommonPartsLibrary #Connector #Header #TSW

ESP32-S3-MINI-1-N8 is a compact, low-power Wi-Fi and Bluetooth module from Espressif Systems based on the ESP32-S3 SoC. It integrates a dual-core Xtensa LX7 processor, 8 MB flash memory, crystal oscillator, RF matching circuitry, and a PCB antenna in a small SMD package, making it ideal for IoT devices, smart home products, industrial automation, HMI applications, AIoT edge devices, and USB-connected embedded systems. Key Features Dual-core 32-bit Xtensa LX7 CPU Up to 240 MHz operating frequency Includes single-precision floating-point unit (FPU) for enhanced processing performance. Integrated Memory 8 MB Quad SPI Flash (N8 variant) 512 KB SRAM 384 KB ROM 16 KB RTC SRAM. Wireless Connectivity 2.4 GHz Wi-Fi 4 (802.11 b/g/n) Data rates up to 150 Mbps Bluetooth 5 LE with Bluetooth Mesh support Simultaneous Wi-Fi and Bluetooth operation through an integrated coexistence mechanism. Rich Peripheral Set Up to 39 GPIOs USB 2.0 OTG USB Serial/JTAG SPI, I²C, I²S, UART PWM, MCPWM SDIO Host ADC Touch sensing Temperature sensor TWAI® (CAN 2.0 compatible) Timers and watchdogs. Integrated Components On-board 40 MHz crystal oscillator PCB antenna RF matching network Compact certified module design. Operating Conditions Supply voltage: 3.0 V to 3.6 V Operating temperature: −40°C to +85°C. Compliance RoHS and REACH compliant RF-certified module for simplified product development. #RF_transceiver #Module #Esp32

Air Quality Sensor CO2 Sensor 2.5V/3.3V/5V 20-Pin SMD EP T/R The SCD41-D-R1 is a miniature photoacoustic carbon dioxide sensor module developed by Sensirion for high-accuracy environmental sensing applications. The device integrates a CO₂ sensing element, temperature sensor, humidity sensor, optical components, calibration memory, and digital signal processing into a compact surface-mount package suitable for embedded systems and portable electronics. The sensor utilizes photoacoustic sensing technology to provide precise carbon dioxide concentration measurements while maintaining low power consumption and long-term stability. Integrated humidity and temperature sensing capabilities enable environmental compensation and simplify system integration by reducing the need for external sensors. The SCD41 communicates through a standard I²C digital interface and supports automatic self-calibration functions for reliable long-term operation. Its compact footprint and low energy requirements make it suitable for battery-powered devices, smart building systems, HVAC equipment, indoor air quality monitoring systems, and IoT applications. The module is factory calibrated and designed for continuous monitoring of indoor air quality conditions. The integrated architecture minimizes external component requirements while enabling accurate sensing performance across a wide operating range. Key Features Photoacoustic CO₂ sensing technology Integrated temperature and humidity sensing High accuracy carbon dioxide measurement I²C digital communication interface Low power consumption operation Automatic self-calibration support Compact surface-mount package Factory calibrated output Long-term measurement stability Optimized for indoor air quality applications Low-profile PCB mounting design RoHS and halogen-free compliant Electrical Characteristics Low-voltage supply operation Low average current consumption suitable for portable devices Integrated digital signal processing Non-volatile calibration memory Standard I²C communication compatibility Stable operation across industrial environmental conditions Mechanical Characteristics Compact SMD package for space-constrained applications Surface-mount assembly compatible Low-profile package structure Integrated optical cavity and sensing chamber Moisture-sensitive device requiring controlled handling during assembly Functional Characteristics Real-time carbon dioxide concentration monitoring Simultaneous temperature and humidity measurement Automatic environmental compensation Continuous and periodic measurement modes Fast startup and measurement response Long operational lifetime with stable calibration Optimized airflow design for accurate sensing Suitable for continuous indoor environmental monitoring Typical Applications Indoor air quality monitoring systems Smart thermostats and HVAC controllers Building automation equipment Demand-controlled ventilation systems Portable environmental monitoring devices Smart home and IoT products Air purification systems Occupancy and ventilation monitoring Battery-powered sensing devices Consumer and industrial environmental monitoring equipment #commonpartslibrary #sensor #airquality

The TPS6213x series, manufactured by Texas Instruments, includes highly efficient, easy-to-use synchronous step-down DC-DC converters optimized for applications requiring high power density. These converters operate within a wide input voltage range from 3 V to 17 V and are capable of delivering up to 3 A of continuous output current. The series comprises multiple part numbers, namely TPS62130, TPS62130A, TPS62131, TPS62132, and TPS62133, each offering unique output configurations—adjustable outputs for TPS62130 and TPS62130A, and fixed outputs of 1.8 V, 3.3 V, and 5.0 V for TPS62131, TPS62132, and TPS62133 respectively. Key features of the TPS6213x series include the advanced DCS-Control™ topology for improved transient response and high output voltage accuracy, a programmable soft start, seamless transition to power save mode, and selectable operating frequency (either 1.25 MHz or 2.5 MHz). The device also encapsulates robust protection mechanisms such as short circuit and overtemperature protection. Housed in a compact 3-mm x 3-mm QFN-16 package, the IC includes additional functions like a power-good output and 100% duty cycle mode for low dropout conditions. With a highly integrated design that requires minimal external components, the TPS6213x series is ideal for step-down regulation in various applications including standard 12-V rail supplies, POL supplies, embedded systems, and portable devices.

Buck Switching Regulator IC Positive Adjustable 1.8V 1 Output 750mA 8-VFDFN The TPS62840 is a high-efficiency step-down converter with ultra-low operating quiescent current of typically 60 nA. The device contains special circuitry to achieve just 120 nA IQ in 100% mode to further extend battery life near the end of discharge. The device uses DCS-Control to cleanly power radios and operates with a typical switching frequency of 1.8 MHz. In Power-Save Mode, the device extends the light load efficiency down to a load current range of 1 μA and below. 16 predefined output voltages can be selected by connecting a resistor to pin VSET, making the device flexible for various applications with a minimum amount of external components. The STOP pin of the device immediately eliminates any switching noise in order to take a noise-free measurement in test and measurement systems. The TPS62840 provides an output current of up to 750 mA. With an input voltage of 1.8 V to 6.5 V, the device supports multiple power sources such as 2S to 4S Alkaline, 1S to 2S Li-MnO2 , or 1S Li-Ion/LiSOCl2 Features 1• 60-nA operating quiescent current • 100% duty-cycle mode with 120-nA IQ • Input voltage range VIN from 1.8 V to 6.5 V • Output current up to 750 mA • RF friendly DCS-Control™ • 80% efficiency at 1 µA IOUT (3.6 VIN to 1.8 VOUT) • 16 selectable output voltages via VSET pin • Auto transition PFM/PWM or forced-PWM mode • Selectable forced PWM and STOP modes • Output discharge function • 25-nA shutdown current #commonpartslibrary #integratedcircuit #powermanagement #voltageregulator

Tactile Switch SPST-NO Top Actuated Surface Mount TACT 5.2 X 5.2, 1.5 MM H, 260GF PTS526 SK15 SMTR2 LFS #components #tact #tactile #spst

Polymeric PTC Resettable Fuse 6V 500 mA Ih Surface Mount 0603 (1608 Metric), Concave polyfuse 500mA 0603 The 0603L050YR is a surface-mount resettable fuse based on polymeric positive temperature coefficient technology, designed to provide overcurrent protection in compact electronic circuits. Under normal operating conditions, the device exhibits low resistance and allows current to pass with minimal power loss. When exposed to an overcurrent condition, the device transitions to a high-resistance state, effectively limiting the current and protecting downstream components. Once the fault condition is removed and power is cycled or the device cools, the fuse automatically resets to its original low-resistance state. This component is optimized for space-constrained applications requiring reliable, resettable protection, such as portable electronics, battery-powered systems, and low-voltage signal lines. Its small form factor enables integration into dense PCB layouts while maintaining compliance with industry safety standards for overcurrent protection. Package and Mounting: Surface-mount device in standard 0603 footprint, compatible with automated assembly processes including reflow soldering. Electrical Characteristics: The device is designed to maintain normal operation at a defined hold current level and transition to a protective state when the current exceeds its trip threshold. It operates within low-voltage circuits and provides fast response to fault conditions while minimizing nuisance tripping under typical load variations. Functional Behavior: The fuse operates by increasing resistance sharply in response to thermal energy generated by excess current. This behavior reduces current flow and limits fault energy. After removal of the overcurrent condition, the device gradually returns to its conductive state, enabling repeated use without replacement. Applications: Suitable for use in power lines, battery packs, USB interfaces, consumer electronics, and other low-voltage systems where resettable overcurrent protection is required. Compliance and Reliability: Designed to meet relevant safety and environmental standards for electronic components, ensuring stable performance across specified operating conditions and long-term reliability in field applications. #commonpartslibrary #fuse #Circuit-Protection #PTC #ptc #polymeric

Remote Receiver Sensor 38.0kHz 45m Through Hole This IR receiver series is optimized for long burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. The higher the AGC, the better noise is suppressed, but the lower the code compatibility. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. These components have not been qualified to automotive specifications. Individual IC settings to reach maximum performance • Immunity against noise (lamps, LCD TV, Wi-Fi) • Low supply current • Photo detector and preamplifier in one package • Supply voltage: 2.0 V to 5.5 V VS1838B #CommonPartsLibrary #Sensor #Transducer #Optical-Sensor #Photo-Detectors #Remote-Receiver #TSOP38238

Buck Switching Regulator IC Positive Adjustable 1.2V 1 Output 3.5A 8-PowerSOIC (0.154", 3.90mm Width) The LM5013DDAR is a 100-V input, 3.5-A buck switching regulator IC that efficiently steps down high DC voltages (such as 24 V, 48 V, or battery rails) to lower regulated outputs. It is optimized for rugged environments where wide input variations and high reliability are required. It features ultra-low quiescent current operation, making it suitable for systems that require high efficiency even at light load or standby conditions. Key Features Wide input voltage range: 6 V to 100 V Up to 3.5 A output current capability Integrated 100-V high-side MOSFET Non-synchronous buck topology Ultra-low quiescent current (IQ) for high efficiency in standby Constant-on-time (COT) control for fast transient response No external compensation components required Adjustable output voltage (down to ~1.2 V reference) 50 ns minimum on/off time for high step-down ratios Built-in protection features: Overcurrent protection Thermal shutdown Input undervoltage lockout (UVLO) Open-drain power-good (PGOOD) signal for system monitoring Meets low EMI requirements (CISPR 25 Class 5 capable) Package 8-pin SO PowerPAD (DDA) surface-mount package Designed for good thermal performance in high-voltage applications Typical Applications Industrial power supplies (24 V / 48 V systems) Automotive power systems Telecom and networking equipment High cell-count battery systems Motor control and inverter subsystems #LM5013 #BuckConverter #DCDCConverter #TexasInstruments #PowerManagementIC #HighVoltageRegulator #3ARegulator #IndustrialPower #AutomotiveElectronics #SwitchingRegulator #COTController

Automotive, 60-V, 6-A, 30-mΩ, one-channel smart high-side switch with adjustable current limit TPS1HTC30-Q1 is a single-channel, smart high-side switch, with integrated NMOS power FET and charge pump, designed to meet the requirements of 24-V automotive battery systems. The low RON(30 mΩ) minimizes device power dissipation driving a wide range of output load current up to 6-A DC, and the 60- V DC operating range improves system robustness. The device integrates protection features such as thermal shutdown, output clamp, and current limit. These features improve system robustness during fault events such as short circuit. TPS1HTC30-Q1 implements an adjustable current limiting circuit that improves the reliability of the system by reducing inrush current when driving large capacitive loads and minimizing overload current. The device also provides an accurate load current sense that allows for improved load diagnostics such as overload and open-load detection enabling better predictive maintenance. TPS1HTC30-Q1 is available in a small 14-pin, 4.40- mm × 5.0-mm HTSSOP leaded package with 0.65- mm pin pitch minimizing the PCB footprint. • Single-channel smart high-side power switch for 24-V automotive systems with full diagnostics • Wide operating voltage range: 6 V to 60 V – OVP protection: 66 V • Low RON: 30-mΩ typical, 55-mΩ maximum • Low standby current: < 0.5 µA • Low quiescent current (Iq): < 2 mA • Improve system level reliability through adjustable current limiting – Current limit: 2 A –16 A • Accurate current sensing: ±4% at 1 A • Protection – Overload and short-circuit protection – Integrated inductive discharge clamp – Undervoltage lockout (UVLO) protection – Loss of GND, loss of supply protection – Reverse battery protection with external components • Diagnostics – On and off state output open-load and short-tobattery detection – Overload and short to ground detection – Absolute and relative thermal shutdown detection • Functional Safety-Capable – Documentation available to aid functional safety system design • Operating junction temperature: –40 to 125°C • Input control: 1.8-V, 3.3-V and 5-V logic compatible • Integrated fault sense voltage scaling for ADC protection • Qualifications – AEC-Q100 qualified for automotive applications • Temperature grade 1: –40°C to +125°C, TA • 14-pin thermally-enhanced TSSOP package TPS1HTC30AQPWPRQ1 #CommonPartsLibrary #IntegratedCircuit

802.15.4, Bluetooth, WiFi Bluetooth v5.0, Zigbee Transceiver Module 2.4GHz PCB Trace Surface Mount The ESP32-C6-WROOM-1-N8 integrates a 32-bit RISC-V single-core processor running up to 160 MHz, along with 8 MB of embedded SPI flash memory. It supports multiple wireless communication protocols, including: Wi-Fi 6 (802.11ax) in the 2.4 GHz band for improved efficiency and lower latency Bluetooth Low Energy (BLE 5) for short-range communication IEEE 802.15.4 for protocols such as Thread and Zigbee The module features a built-in PCB antenna, RF circuitry, crystal oscillator, and passive components, making it a complete solution that simplifies hardware design. It provides a wide range of GPIO pins and peripheral interfaces such as UART, SPI, I2C, PWM, ADC, and more, enabling flexible integration with sensors and external devices. Designed for low power consumption, it includes multiple power-saving modes, making it suitable for battery-powered applications. Typical Applications Smart home and IoT devices Wireless sensors and control systems Industrial automation Smart lighting and energy management Matter-compatible devices (via Thread support)

1/1 Transceiver Half CANbus 8-SOIC The SN65HVD230DR is a high-speed Controller Area Network (CAN) transceiver designed to interface a CAN protocol controller with the physical two-wire CAN bus. It operates as a differential line driver and receiver, translating logic-level signals into robust bus-level signals suitable for automotive, industrial, and distributed control applications. The device is optimized for reliable communication in electrically noisy environments and supports low-power operation, making it suitable for systems requiring energy efficiency and extended operational stability. This transceiver conforms to widely adopted CAN physical layer standards and is intended for use in systems requiring high data integrity, fault tolerance, and electromagnetic compatibility. It integrates protection features and supports standby functionality to reduce system power consumption when communication is inactive. Functional Overview The device provides bidirectional signal conversion between a CAN controller and the differential CAN bus lines. It features a transmit data input and a receive data output, enabling full-duplex communication at the protocol level. The driver stage generates differential output signals on the bus, while the receiver stage detects and translates bus signals back into logic-level data. An internal control mechanism allows the device to enter a low-power standby mode, reducing current consumption when active communication is not required. The transceiver includes slope control capability to manage signal edge rates, which helps minimize electromagnetic interference and improves signal integrity across the network. Electrical Characteristics The transceiver operates from a single low-voltage supply and is designed for compatibility with modern microcontrollers and digital logic systems. It provides differential output drive capability with controlled rise and fall characteristics. The receiver is designed with high input sensitivity and noise immunity to ensure accurate signal detection under varying bus conditions. The device includes thermal protection and safeguards against bus faults, including short-circuit conditions. Its internal circuitry is designed to maintain stable operation across a wide range of environmental conditions and supply variations. Interface Requirements The logic interface is compatible with standard digital input and output levels, allowing direct connection to a CAN controller. The bus interface consists of two differential lines that connect to the CAN network. Proper termination and layout practices are required to ensure optimal communication performance and compliance with CAN network design guidelines. Operating Conditions The device is intended for operation across a broad temperature range suitable for industrial and automotive environments. It maintains functional integrity under typical voltage fluctuations and environmental stresses encountered in embedded systems. Protection and Reliability Features The transceiver incorporates protection mechanisms to guard against overcurrent, thermal overload, and electrostatic discharge. It is designed to maintain communication reliability even in the presence of transient disturbances and electrical noise. Packaging and Integration The SN65HVD230DR is provided in a compact surface-mount package suitable for automated assembly. Its pin configuration supports straightforward integration into printed circuit board designs with minimal external components. #CommonPartsLibrary #IntegratedCircuits #Interface #Drivers #Receivers #Transceivers #65HVD230

19 Position Header Connector 0.100" (2.54mm) Through Hole Tin 1x19 pin header 2.54mm This component is a single-row female header connector designed for general-purpose board-to-board and wire-to-board interconnections. It provides a reliable and cost-effective solution for standard pitch connectivity in electronic assemblies. The connector is commonly used in prototyping, development boards, and production systems where modular connections and ease of assembly are required. Its design supports compatibility with standard male pin headers, making it suitable for a wide range of applications in industrial, consumer, and embedded electronics. Key Features The connector features a single-row configuration with standard pitch spacing, enabling compatibility with widely used pin header systems. It is constructed with durable insulating material and conductive contacts that provide stable electrical performance. The contacts are designed to ensure consistent mating force and reliable signal transmission. The component supports through-hole mounting for strong mechanical retention and ease of soldering. Its construction allows repeated mating cycles while maintaining contact integrity. Electrical Characteristics The connector is designed to support typical signal and low-power applications in electronic circuits. It provides consistent electrical contact with low contact resistance and stable conductivity under normal operating conditions. The materials and plating are selected to ensure reliable performance over time, minimizing oxidation and degradation during use. Mechanical and Material Characteristics The housing is made from a high-temperature thermoplastic material suitable for standard soldering processes. The contacts are formed from conductive metal alloy and finished with a protective plating to enhance durability and conductivity. The connector is designed for vertical mounting orientation and aligns with standard printed circuit board layouts for through-hole components. Thermal Characteristics The component is suitable for typical operating temperature ranges encountered in electronic assemblies. The housing material is resistant to heat generated during soldering and normal operation, ensuring structural integrity and long-term reliability. Applications This connector is widely used in embedded systems, development platforms, consumer electronics, industrial control systems, and communication equipment. It is ideal for applications requiring modular connectivity, easy replacement, and reliable electrical interfacing between boards or components. Compliance and Standards The component is manufactured in accordance with industry standards for electronic connectors and is suitable for use in systems requiring dependable mechanical and electrical performance. It supports common environmental and material compliance requirements for modern electronic manufacturing. #commonpartslibrary #connector #header

Wio-E5 Dev Kit embedded with Wio-E5 STM32WLE5JC LoRa module that supports Long Range protocol on the global frequency band. It provides full GPIOs, which support various data protocols and interfaces such as RS485, Grove, male/female headers, etc. This makes it user-friendly because it allows for easy and flexible connections to other devices or components. It would be a perfect choice for fast testing and rapid prototyping of your Long Range IoT projects.

Amplifier IC 2-Channel (Stereo) Class D 28-HTSSOP TPA3110D2PWP ay isang high-efficiency Class-D stereo audio power amplifier IC na dinisenyo para sa consumer audio applications tulad ng speakers, televisions, at portable audio systems. Kaya nitong mag-deliver ng hanggang 15 W per channel sa stereo mode o 30 W mono sa bridge configuration habang mababa ang power loss dahil sa efficient Class-D architecture. Key Features 15 W/ch stereo output into 8 Ω load at 16 V supply 30 W mono output into 4 Ω load (BTL mode) High efficiency (~90%) kaya madalas hindi na kailangan ng malaking heatsink Wide operating voltage: 8 V to 26 V Filter-free operation para mabawasan ang external components Integrated SpeakerGuard™ protection Adjustable power limiter DC speaker protection Built-in: Short-circuit protection Thermal shutdown with auto recovery Overcurrent protection Differential audio inputs para mas magandang noise immunity Four selectable gain settings EMI suppression technology para mas madaling pumasa sa EMC requirements Available sa 28-pin HTSSOP (PWP) package na may exposed thermal pad Typical Applications LCD/LED televisions Bluetooth speakers Consumer audio amplifiers DIY stereo amplifier boards Powered speakers Home audio systems #commonpartslibrary #integratedcircuit #linearamplifier #audioamplifier

Non-Isolated PoL Module DC DC Converter 1 Output 1 ~ 36V 12A 5V - 36V Input The LTM®4712 is a high efficiency buck-boost µModule® (micromodule) regulator. The switching controller, power switches, inductor and support components are included in the package. The complete design requires only a few external components, including a resistor to set frequency, a resistor to set output voltage, input, and output capacitors, a sensing resistor to achieve input or output average current regulation. The LTM4712 operates over a 5V to 36V input voltage range and can regulate output voltages between 1V and 36V. The LTM4712 supports selectable forced continuous mode (FCM)/pulse-skipping mode (PSM) operation. The current mode control enables a fast transient response to line and load changes without sacrificing stability. The SYNC input and CLKOUT output allow easy synchronization. It supports multi-phase parallel operation for high power applications. The LTM4712 is offered in a 16mm × 16mm × 8.34mm ball grid array (BGA) package suitable for automated assembly by standard surface mount equipment. The LTM4712 is RoHS-compliant n Complete Buck-Boost Switch Mode Power Supply n VOUT Equal, Greater, Less Than VIN n Wide Input Voltage Range: 5V to 36V n Wide Output Voltage Range: 1V to 36V n 12A in Buck and Buck-Boost Mode, 6A under 12VIN and 24VOUT n Up to 98% Efficiency n Peak Current Mode Control n Adjustable Input or Output Average Current Limits n Input or Output Current Monitoring n Power Good Output Signal n Parallelable for Increased Output Current n Phase-Lockable Fixed Frequency: 100kHz to 600kHz n Selectable Forced Continuous/Pulse-Skipping Modes n VOUT is Disconnected from VIN During Shutdown n 16mm ×16mm × 8.34mm BGA Package #Power-supply

Air Quality Sensors VOC and NOx (MOX) Gas Pollutant Sensor The SGP41-D-R4 is a compact digital gas sensor developed by Sensirion for indoor air quality monitoring applications. It is designed to detect volatile organic compounds (VOC) and nitrogen oxides (NOx) using Sensirion’s CMOSens® sensor technology. The device integrates sensing elements, analog front-end circuitry, calibration memory, and digital signal processing within a miniature surface-mount package, enabling accurate and reliable environmental sensing with minimal external components. The sensor communicates through a standard I²C digital interface and is optimized for low-power operation, making it suitable for battery-powered and portable electronic systems. The SGP41 is intended for use in air purifiers, HVAC systems, smart home devices, wearable electronics, environmental monitoring equipment, and other applications requiring real-time indoor air quality assessment. The device supports humidity-compensated measurements when paired with an external humidity and temperature sensor, improving long-term stability and measurement accuracy. Factory calibration eliminates the need for manual calibration during manufacturing. Key Features Digital VOC and NOx gas sensing CMOSens® technology integration I²C communication interface Fully calibrated and linearized output Humidity compensation capability Low power consumption operation Compact DFN surface-mount package Fast response and recovery characteristics Optimized for indoor air quality applications RoHS and halogen-free compliant Electrical Characteristics Supply voltage operation compatible with low-voltage embedded systems Low average current consumption suitable for portable devices Integrated digital signal processing and calibration memory I²C serial communication support with standard addressing Stable operation across industrial temperature ranges Mechanical Characteristics Small DFN package optimized for compact PCB layouts Surface-mount assembly compatible Low-profile package suitable for space-constrained designs Moisture-sensitive device requiring proper handling during assembly Functional Characteristics Simultaneous VOC and NOx sensing capability Real-time indoor air quality monitoring Compensation support for environmental humidity effects Long-term measurement stability Fast startup and measurement readiness Designed for continuous sensing applications Typical Applications Indoor air quality monitoring systems Smart thermostats and HVAC controllers Air purifiers and ventilation systems Smart home and IoT devices Portable environmental monitoring equipment Wearable health and wellness devices Building automation systems Consumer electronics requiring air quality detection #Sensor #Transducer #Gas#Sensor #SGP41

Electronic Fuse Regulator High-Side 10A 10-VQFN-HR (2x2) The TPS25981xx family of eFuses is a highly integrated circuit protection and power management solution in a small package. The devices provide multiple protection modes using very few external components and are a robust defense against overloads, short circuits, voltage surges and excessive inrush current. Output slew rate and inrush current can be adjusted using a single external capacitor. Loads are protected from input overvoltage conditions by cutting off the output if input exceeds an adjustable overvoltage threshold. The devices respond to output overload by actively limiting the current (during startup) or breaking the circuit (during steady-state). The overcurrent protection threshold as well as the transient overcurrent blanking timer are useradjustable. The current limit control pin also functions as an analog load current monitor. The devices are available in a 2-mm × 2-mm, 10- pin HotRod™ QFN package for improved thermal performance and reduced system footprint. The devices are characterized for operation over a junction temperature range of –40°C to +125°C. • Wide operating input voltage range: 2.7 V to 16 V – 20-V absolute maximum • Integrated FET with low on-resistance: RON = 6 mΩ (typ.) • Fast overvoltage protection – Adjustable overvoltage lockout (OVLO) with 1.2-μs (typ.) response time • Overcurrent protection with load current monitor output (ILM) – Circuit-breaker response – Adjustable threshold (ILIM) 1.5 A – 11 A • ±10% accuracy for ILIM > 5 A – Adjustable transient blanking timer (ITIMER) to allow peak currents up to 2 × ILIM – Output load current monitor accuracy: ±10% (IOUT ≥ 3 A) • Fast-trip response for short-circuit protection – 640-ns (typ.) response time – Adjustable (2 × ILIM) and fixed thresholds • Active high enable input with adjustable undervoltage lockout threshold (UVLO) • Active low enable input with adjustable undervoltage lockout threshold (OVLO) • Adjustable output slew rate control (dVdt) • Option to drive external FET for reverse current blocking in disabled/OFF state • Overtemperature protection • Quick Output Discharge • Digital outputs – Power Good (PG) and fault indication (FLT) • UL 2367 recognition (pending) • IEC 62368 CB certification (pending) • Small footprint: QFN 2-mm × 2-mm, 0.45-mm pitch #CommonPartsLibrary #IntegratedCircuit #PowerManagement

Supervisor Open Drain or Open Collector 1 Channel SOT-23-5 The TPS382x family of supervisors provide circuit initialization and timing supervision, primarily for DSP and processor-based systems. During power on, RESET asserts when the supply voltage VDD becomes greater than 1.1V. Thereafter, the supply voltage supervisor monitors VDD and keeps RESET active low as long as VDD remains less than the threshold voltage, VIT−. An internal timer delays the return of the output to the inactive state (high) to make sure proper system reset. The delay time, td, starts after VDD has risen above the threshold voltage (VIT− + VHYS). When the supply voltage drops below the threshold voltage VIT−, the output becomes active (low) again. No external components are required. All the devices of this family have a fixed-sense threshold voltage, VIT–, set by an internal voltage divider. The TPS382x family also offers watchdog time out options of 200ms (TPS3820) and 1.6s (TPS3823, TPS3824, and TPS3828). • Power-on reset generator with a fixed delay time of 200ms (TPS3823, TPS3824, TPS3825, and TPS3828) or 25ms (TPS3820) • Manual reset input (TPS3820, TPS3823, TPS3825, and TPS3828) • Reset output available in active-low (TPS3820, TPS3823, TPS3824, and TPS3825), active-high (TPS3824 and TPS3825), and open drain (TPS3828) • Supply voltage supervision range: 2.5V, 3V, 3.3V, 5V • Watchdog timer (TPS3820, TPS3823, TPS3824, and TPS3828) • Supply current of 15μA (typical) • 5-pin SOT-23 package • Temperature range: −40°C to 85°C (−40°C to 125°C for TPS3823A-33) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Supervisor

IC RF TxRx + MCU 802.15.4, Bluetooth Bluetooth v5.0, Thread, Zigbee® 2.4GHz 48-VFQFN Exposed Pad The NRF52840-QFAA-F-R belongs to Nordic’s nRF52 series and supports multiple wireless standards including Bluetooth 5, Bluetooth Low Energy (BLE), Thread, Zigbee, ANT, and proprietary 2.4 GHz protocols. It features a 64 MHz ARM Cortex-M4F CPU with floating-point unit (FPU), making it suitable for both wireless communication and real-time embedded processing. The device integrates large memory resources, rich peripherals, USB support, NFC capability, and advanced security features, reducing the need for external components in wireless embedded designs. Key Features 32-bit ARM Cortex-M4F processor running at 64 MHz 1 MB Flash memory and 256 KB RAM Supports Bluetooth 5 / BLE, Thread, Zigbee, ANT, and proprietary 2.4 GHz protocols IEEE 802.15.4 compliant radio Up to +8 dBm TX output power High receiver sensitivity down to −103 dBm Data rates up to 2 Mbps Ultra-low power consumption for battery-powered applications USB 2.0 Full-Speed controller NFC-A tag support Multiple communication interfaces: SPI UART I2C (TWI) I2S PWM PDM ADC Up to 48 GPIOs Integrated ARM CryptoCell-310 security engine Operating voltage range: 1.7 V to 5.5 V Operating temperature: −40°C to +85°C Compact 48-QFN (6×6 mm) package Typical Applications BLE devices Smart home products Wearables Wireless sensors Industrial IoT HID devices (keyboard/mouse) Asset tracking Mesh networking devices USB dongles and gateways PCB Design Notes Community PCB reviews commonly recommend: Proper RF grounding and 50-ohm antenna routing Using ESD/TVS protection on USB lines Keeping RF matching components close to the antenna Using solid ground planes for 2.4 GHz performance #CommonPartsLibrary #IntegratedCircuit #RF