The NE555 devices are precision timing circuits capable of producing accurate time delays or oscillation. In time-delay or monostable operating modes, the timed interval is controlled by a single external resistor and capacitor network. In the astable mode of operation, the frequency and duty cycle are controlled independently with two external resistors and a single external capacitor. Each timer has a trigger level equal to approximately one-third of the supply voltage and a threshold level equal to approximately two-thirds of the supply voltage. These levels can be altered by use of the control voltage pin (CONT). When the trigger input (TRIG) is less than the trigger level, the flip-flop is set and the output goes high. If TRIG is greater than the trigger level and the threshold input (THRES) is greater than the threshold level, the flip-flop is reset and the output is low. The reset input (RESET) overrides all other inputs and is used to initiate a new timing cycle. If RESET is low, the flip-flop is reset and the output is low. Whenever the output is low, a lowimpedance path is provided between the discharge pin (DISCH) and the ground pin (GND). Tie all unused inputs to an appropriate logic level to prevent false triggering. The output circuit is capable of sinking or sourcing current up to 200mA. Operation is specified for supplies of 5V to 15V. With a 5V supply, output levels are compatible with TTL inputs. Features - Timing from microseconds to hours - Astable or monostable operation - Adjustable duty cycle - TTL-compatible output can sink or source up to 200mA - On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. Applications - Pulse-shaping circuits - Missing-pulse detectors - Pulse-width modulators - Pulse-position modulators - Sequential timers - Pulse generators -F requency dividers - Industrial controls

Slide Switch SPST 4A 125V Throuh Hole The L101011MS02Q is a single-pole, single-throw (SPST) miniature toggle switch designed for low-power switching applications. It features a compact panel-mount design with a durable actuator and reliable contact mechanism, making it suitable for control and signal switching in industrial, instrumentation, and consumer electronics. The switch provides a maintained (latching) ON-OFF function and is built for long mechanical and electrical life. Key Features SPST (Single Pole, Single Throw) configuration ON-OFF maintained switching function Miniature toggle actuator Panel mount design with threaded bushing Solder lug terminals for secure wiring High mechanical durability Compact form factor Mechanical Characteristics Mounting Type: Panel mount Actuator Type: Toggle lever Bushing Type: Threaded, with nut and washer Terminal Type: Solder lug Number of Poles: 1 Number of Throws: 1 Switching Function: ON-OFF (latching) Electrical Characteristics Rated Voltage: 125 VAC / 28 VDC Rated Current: 3 A @ 125 VAC, 6 A @ 28 VDC Contact Resistance: ≤ 20 mΩ (initial) Insulation Resistance: ≥ 1,000 MΩ Dielectric Strength: 1,000 VAC for 1 minute Material Specifications Housing: Thermoplastic or phenolic (manufacturer dependent) Actuator: Metal (nickel-plated brass) Contacts: Copper alloy with silver plating Terminals: Brass, tin-plated Environmental Specifications Operating Temperature Range: -30°C to +85°C Storage Temperature: -40°C to +85°C Mechanical Life Mechanical Life: ≥ 40,000 cycles Electrical Life: ≥ 10,000 cycles (at rated load) Typical Applications Control panels Power switching for small devices Instrumentation equipment Audio equipment Industrial and consumer electronics #commonpartslibrary #rocker #switch #spst

555 Type, Timer/Oscillator (Single) IC 100kHz 8-PDIP NE555 DIP-8 through hole The NE555P is a classic and widely used precision timer IC manufactured by companies like Texas Instruments and others. It belongs to the popular 555 timer family and is designed for generating accurate time delays, oscillations, and pulse signals. The “P” variant refers to the PDIP (Plastic Dual In-line Package), making it ideal for through-hole mounting, breadboarding, and prototyping. NE555P PDIP-8 timer Internally, the NE555P consists of: Two comparators A flip-flop A discharge transistor A voltage divider network These blocks allow flexible configuration for timing and waveform generation. Key Features Timing & Operation Modes Monostable mode (one-shot pulse generation) Astable mode (continuous oscillator) Bistable mode (flip-flop operation) Electrical Characteristics Supply voltage range: 4.5V to 16V Output can source or sink up to 200 mA Adjustable duty cycle Performance High timing accuracy and stability Timing range from microseconds to hours (depends on external R and C) Temperature-stable operation Package & Usability 8-pin DIP (through-hole) package Easy to use for: Breadboards DIY electronics Educational projects Common Applications LED flashers and blinkers Pulse generation Time delay circuits PWM control (e.g., dimming LEDs, motor speed control) Tone/sound generation #Timer #commonpartslibrary

Electronic Fuse Regulator 5.3A 20-WQFN (3x4) The TPS25940LRVCR is a compact eFuse (electronic fuse) power management IC from Texas Instruments designed to provide advanced power-path protection and load management for systems such as SSDs, servers, storage devices, and embedded electronics. It integrates protection features like overcurrent limiting, reverse current blocking, overvoltage protection, and controlled startup sequencing into a single chip. Wide input voltage range: 2.7 V to 18 V Adjustable current limit: 0.6 A to 5.3 A Low ON resistance: 42 mΩ typical True reverse current blocking using back-to-back MOSFETs Programmable output slew rate (dV/dt control) for inrush current management Overvoltage and undervoltage protection Fault and Power-Good outputs for system monitoring Current monitor (IMON) output Low-power DevSleep support for SSD applications Fast reverse voltage shutdown (~1 µs) Operating temperature: −40°C to +125°C junction temperature Available in a compact 20-pin WQFN package Typical Applications PCIe / SATA / SAS SSDs and HDDs Enterprise servers and storage systems RAID controller cards Smart load switches Set-top boxes and gaming systems Backup power and holdup capacitor systems Component Category This component belongs to: Power Management IC (PMIC) More specifically: eFuse / Hot-swap / Load Switch IC Package Information Package type: 20-WQFN (3 mm × 4 mm) Mounting type: Surface Mount (SMD) #commonpartslibrary #integratedcircuit #powermanagement #currentregulation

Connector Header Through Hole 6 position 0.100" (2.54mm) The 640456-6 is a 6-position, single-row wire-to-board header connector from TE Connectivity (AMP series), designed for reliable power and signal connections in a wide range of electronic applications. It features a 2.54 mm pitch and through-hole mounting for strong mechanical retention and ease of assembly. The connector is commonly used with matching crimp housings and terminals, providing a secure and serviceable interconnect solution for PCB-based systems. Key Features 6-position (1x6) header connector 2.54 mm pitch spacing Through-hole mounting (THT) Vertical (top-entry) orientation Friction-lock compatible with mating housings Tin-plated contacts for good conductivity and corrosion resistance Durable thermoplastic housing Mechanical Characteristics Mounting Type: Through Hole Orientation: Vertical (Top Entry) Pitch: 2.54 mm Number of Positions: 6 Row Configuration: Single row Mating Type: Friction fit with compatible housing Termination Type: Solder tails Electrical Characteristics Rated Current: Up to 3 A per contact (depending on wire gauge) Rated Voltage: 250 V AC/DC Contact Resistance: ≤ 20 mΩ (initial) Insulation Resistance: ≥ 1,000 MΩ Dielectric Withstanding Voltage: 1,000 VAC Material Specifications Housing: Thermoplastic, UL94V-0 rated Contacts: Copper alloy Contact Plating: Tin over nickel Environmental Specifications Operating Temperature Range: -40°C to +105°C Storage Temperature: -40°C to +105°C Packaging Information Packaging Type: Bulk or tray (varies by supplier) RoHS Compliant: Yes Lead-Free: Yes Compatible Components Mating Housing: TE Connectivity compatible crimp housings (e.g., AMP series) Crimp Terminals: соответствующие crimp contacts for 2.54 mm systems Typical Applications PCB interconnects Consumer electronics Industrial control systems Power and signal distribution Prototyping and development boards #CommonPartsLibrary #Connector #Header #Male-pins #MTA-100

Tactile Switch SPST-NO Top Actuated Surface Mount The FSM1LP is a surface-mount tactile (momentary) switch manufactured by TE Connectivity under the ALCOSWITCH series. It is a low-profile, top-actuated pushbutton switch designed for compact PCB applications requiring reliable user input. This switch operates as a momentary SPST-NO (Single Pole Single Throw – Normally Open) device, meaning it only conducts when pressed and returns to open when released. Key Features Switch Type Tactile momentary (OFF–(ON)) pushbutton Contact Configuration SPST-NO (Normally Open) Mounting Type Surface Mount (SMD) with gull-wing leads Actuation Style Top-actuated round button Electrical Rating 50 mA @ 24 VDC Operating Force Approximately 1.57 N (~160 gf) Low Profile Design Compact height (~3–3.5 mm typical), suitable for slim devices Mechanical Life Around 100,000 cycles Contact Material Copper alloy with silver plating for reliable conductivity Compact Size Typically ~6 × 6 mm footprint RoHS Compliant Lead-free and environmentally compliant tactile switch momentary 4 pin smd #CommonPartsLibrary #Switch

Battery Holder (Open) 9V 1 Cell PC Pin 9V battery holder through hole The BH9VPC is a through-hole, printed circuit board–mount battery holder designed to accommodate a single standard 9 V (PP3) battery. It provides a secure mechanical enclosure and reliable electrical interface for powering electronic assemblies directly from a PCB. The holder is constructed from durable insulating material with integrated metal contacts to ensure stable retention and consistent electrical connection during operation. Its form factor supports straightforward integration into compact designs while maintaining ease of battery replacement. Engineering Specification: The component is intended for through-hole mounting using PC pins that provide both mechanical stability and electrical connection to the circuit board. It supports one 9 V battery with standard snap terminal interface internally routed to PCB pins. The housing material is typically molded plastic with good mechanical strength and electrical insulation properties suitable for general electronic applications. Contact terminals are metal, commonly nickel-plated or equivalent, to ensure low contact resistance and corrosion resistance over repeated battery insertions. The holder is designed for vertical mounting orientation relative to the PCB, with a compact footprint suitable for space-constrained layouts. It provides sufficient retention force to secure the battery under normal handling and vibration conditions encountered in consumer and light industrial electronics. The operating characteristics are aligned with typical 9 V battery usage, supporting low to moderate current applications depending on battery capability. The part is compatible with standard wave soldering processes used in through-hole assembly. It is intended for use in ambient environmental conditions typical of indoor electronic equipment and is not inherently sealed against moisture or contaminants. The design allows easy manual insertion and removal of the battery without specialized tools, supporting maintenance and replacement in field applications. #commonpartslibrary #batteryholder

Tactile Switch SPST-NO Top Actuated Surface Mount The B3FS-1002P is a compact, surface-mount tactile switch designed for low-profile input applications. It provides a momentary contact mechanism with a distinct tactile feedback, making it suitable for user interface controls in consumer electronics, industrial devices, and compact embedded systems. The switch features a sealed construction for improved reliability and is optimized for automated PCB assembly processes. Mechanical Characteristics Mounting Type: Surface Mount (SMD) Actuator Style: Top push Actuator Height: Low profile Outline: Rectangular compact body Terminal Type: Gull-wing terminals Sealing: Dust-resistant (sealed construction) Electrical Characteristics Switch Type: Single Pole Single Throw (SPST) Contact Configuration: Normally Open (NO) Rated Voltage: Low voltage DC applications Rated Current: Suitable for signal-level switching Contact Resistance: Low initial contact resistance Insulation Resistance: High insulation resistance between terminals Operating Characteristics Operating Force: Standard tactile force (manufacturer-defined variant) Travel Distance: Short stroke tactile action Operating Life: High durability for repeated actuation cycles Bounce Time: Minimal contact bounce for reliable switching Environmental Characteristics Operating Temperature Range: Wide operating range suitable for consumer and industrial use Storage Temperature Range: Standard electronic component storage conditions Humidity Resistance: Designed to withstand typical ambient humidity conditions Material & Construction Actuator Material: High-strength polymer Housing Material: Heat-resistant plastic Contact Material: Metal alloy with surface plating for durability Terminal Finish: Solderable finish compatible with reflow soldering Packaging Information Packaging Type: Tape and reel Assembly Compatibility: Fully compatible with automated pick-and-place and reflow processes Applications Consumer electronics (keypads, remote controls) Industrial control panels Portable devices Embedded system user interfaces Wearable and compact electronics #commonpartslibrary #switch #tactile

Fuse Holder 32V 1 Circuit Blade Through Hole The 178.6764.0001 is an automotive blade fuse holder from Littelfuse, part of the MINI® FL1 series, designed for direct PCB mounting (through-hole). It allows easy integration of a single MINI blade fuse into a printed circuit board for overcurrent protection. This component is commonly used in automotive electronics, industrial control systems, and embedded power circuits, where compact and reliable fuse protection is required. Key Features Fuse Type Compatibility Supports MINI® automotive blade fuses (ATM/APM type) PCB Mount (Through-Hole) Designed for direct soldering to PCB for strong mechanical support Current Capability Up to 30 A maximum ~22 A continuous rating Voltage Rating Up to 58 VDC (automotive systems) Single Fuse Position Holds 1 fuse per holder Thermoplastic Housing Heat-resistant black body UL94 V-0 flammability rating for safety Contact Material Tin-plated copper alloy terminals for reliable conductivity Standard PCB Pitch Approx. 7.62 mm pin spacing Modular Design Multiple holders can be mounted side-by-side for multi-channel protection blade fuse holder automotive PCB #Circuit-Protection #Fuseholders #FL1

Bluetooth, WiFi 802.11b/g/n, Bluetooth v5.0 Transceiver Module 2.4GHz PCB Trace Surface Mount The ESP32-C3-WROOM-02-N4 is a compact, general-purpose Wi-Fi and Bluetooth Low Energy (BLE) module developed by Espressif Systems. It is built around the ESP32-C3 SoC and integrates RF components, crystal oscillator, flash memory, and PCB antenna in a single module. It is designed for a wide range of applications such as IoT devices, smart home systems, industrial automation, and consumer electronics, offering a balance of performance, low power consumption, and cost efficiency. Key Features MCU & Memory 32-bit RISC-V single-core processor up to 160 MHz 384 KB ROM 400 KB SRAM + 8 KB RTC SRAM Integrated 4 MB SPI flash (N4 variant) Connectivity 2.4 GHz Wi-Fi (802.11 b/g/n) Supports Station, SoftAP, and Station + SoftAP modes Bluetooth 5 (BLE) with mesh support Data rates up to 150 Mbps (Wi-Fi) Peripherals & Interfaces Up to 15 GPIOs Interfaces: SPI, UART, I2C, I2S LED PWM ADC (SAR) Timers & watchdog USB Serial/JTAG support TWAI® (CAN 2.0 compatible) #commonpartslibrary #transceiver #module #wireless #rf

MAX98357A Series 5.5V 3.2W PCM Input Class D Audio Power Amplifier - TQFN-16 The MAX98357A/MAX98357B is an easy-to-use, low-cost, digital pulse-code modulation (PCM) input Class D amplifier that provides industry-leading Class AB audio performance with Class D efficiency. The digital audio interface automatically recognizes up to 35 different PCM and TDM clocking schemes which eliminates the need for I2C programming. Operation is further simplified by eliminating the need for an external MCLK signal that is typically used for PCM communication. Simply supply power, LRCLK, BCLK, and digital audio to generate audio! Furthermore, a novel pinout allows customers to use the cost-effective WLP package with no need for expensive vias (refer to Application Note 6643: Optimize Cost, Size, and Performance with MAX98357 WLP for more information). The digital audio interface is highly flexible with the MAX98357A supporting I2S data and the MAX98357B supporting left-justified data. Both ICs support 8 channel time division multiplexed (TDM) data. The digital audio interface accepts specified sample rates between 8kHz and 96kHz for all supported data formats. The ICs can be configured to produce a left channel, right channel, or (left/2 + right/2) output from the stereo input data. The ICs operate using 16/24/32-bit data for I2S and left-justified modes as well as 16-bit or 32-bit data using TDM mode. The ICs eliminate the need for the external MCLK signal that is typically used for PCM communication. This reduces EMI and possible board coupling issues in addition to reducing the size and pin count of the ICs. The ICs also feature a very high wideband jitter tolerance (12ns typ) on BCLK and LRCLK to provide robust operation. Active emissions-limiting, edge-rate limiting, and overshoot control circuitry greatly reduce EMI. A filterless spread-spectrum modulation scheme eliminates the need for output filtering found in traditional Class D devices and reduces the component count of the solution. The ICs are available in 9-pin WLP (1.345mm x 1.435mm x 0.64mm) and 16-pin TQFN (3mm x 3mm x 0.75mm) packages and are specified over the -40°C to +85°C temperature range. ● Single-Supply Operation (2.5V to 5.5V) ● 3.2W Output Power into 4Ω at 5V ● 2.4mA Quiescent Current ● 92% Efficiency (RL = 8Ω, POUT = 1W) ● 22.8μVRMS Output Noise (AV = 15dB) ● Low 0.013% THD+N at 1kHz ● No MCLK Required ● Sample Rates of 8kHz to 96kHz ● Supports Left, Right, or (Left/2 + Right/2) Output ● Sophisticated Edge Rate Control Enables Filterless Class D Outputs ● 77dB PSRR at 1kHz ● Low RF Susceptibility Rejects TDMA Noise from GSM Radios ● Extensive Click-and-Pop Reduction Circuitry ● Robust Short-Circuit and Thermal Protection ● Available in Space-Saving Packages: 1.345mm x 1.435mm WLP (0.4mm Pitch) and 3mm x 3mm TQFN ● Solution Size with Single Bypass Capacitor is 4.32mm2 Applications ● Single Li-ion Cell/5V Devices ● Smart Speakers ● Notebook Computers ● IoT Devices ● Gaming Devices (Audio and Haptics) ● Smartphones ● Tablets ● Cameras #commonpartslibrary #integratedcircuit #linearamplifier #mono

Bipolar (BJT) Transistor NPN 40V 200 mA 300MHz 625 mW Through Hole TO-92-3 The 2N3904TFR is a general-purpose NPN bipolar junction transistor (BJT) designed for low-power amplification and switching applications. It is widely used in signal processing, small-signal amplification, and digital switching circuits. This transistor offers fast switching speed, low saturation voltage, and reliable performance in a compact surface-mount package, making it suitable for consumer electronics, industrial controls, and embedded systems. Manufacturer Various (commonly ON Semiconductor / onsemi, Diodes Inc., Central Semiconductor) Part Number 2N3904TFR Transistor Type NPN Bipolar Junction Transistor (BJT) Configuration Single Package / Case SOT-23 (TO-236AB) Mounting Style Surface Mount (SMD/SMT) Collector-Emitter Voltage (VCEO) 40 V Collector-Base Voltage (VCBO) 60 V Emitter-Base Voltage (VEBO) 6 V Collector Current (IC) 200 mA (max) Power Dissipation (PD) ~200 mW to 350 mW (package dependent) DC Current Gain (hFE) 100 to 300 (typical, varies with operating conditions) Transition Frequency (fT) ~300 MHz Collector-Emitter Saturation Voltage (VCE(sat)) ~0.2 V (typical at IC = 10 mA, IB = 1 mA) Operating Temperature Range -55°C to +150°C Polarity NPN Packaging Tape & Reel (TFR suffix) RoHS Compliance Compliant #commonpartslibrary #transistor #bjt

Through hole straight pin header, 1x04, 4 pin, 4-pin, horizontal, angled, 2.54mm pitch, 6mm pin lenght single row

Single Port RJ45 Connector With Integrated Magnetics And LED. This is HanRun's single port RJ45 ethernet connector with Integrated magnetics and LED for 10/100Base-T NIC applications. #CommonPartsLibrary #Connector #Ethernet

4 Position Header Connector 0.100" (2.54mm) Through Hole Tin, Insulation Height 0.335" (8.51mm), single row #pinsocket #tht

JST PH Connector Header Through Hole, Right Angle 4 position 0.079" (2.00mm) The S4B-PH-K-S(LF)(SN) is a 4-position, single-row, right-angle (side-entry) male header designed for 2.0 mm pitch wire-to-board connections. It is a through-hole mounted, shrouded connector that ensures reliable and secure mating with compatible PH series housings and crimp terminals. This connector is commonly used in consumer electronics, embedded systems, power supplies, and industrial control boards, especially where space-saving and dependable connections are required. Key Features Connector Type: Shrouded male header (wire-to-board) Number of Positions: 4 pins (single row) Pitch: 2.0 mm Orientation: Right-angle (side entry) Mounting Type: Through-hole (THT) Termination: Solder Electrical Characteristics Rated Voltage: 100 V Rated Current: 2 A per contact Insulation Resistance: ≥1000 MΩ Contact Resistance: Low (typically ≤10–20 mΩ) Mechanical & Material Contact Material: Brass / phosphor bronze with tin plating Housing Material: PA66 (Nylon), UL94 V-0 flame rated Locking Mechanism: Detent lock for secure mating Shrouded Design: Prevents misalignment and protects pins Environmental Operating Temperature: −25 °C to +85 °C #CommonPartsLibrary #Connector #Header #JSTPH #MalePins #RightAngle #4pos

6 Position Header Connector 0.100" (2.54mm) Through Hole Tin, Insulation Height 0.335" (8.51mm) single row #pinsocket #tht

555 Type, Timer/Oscillator (Single) IC 100kHz 8-SOIC #commonpartslibrary #integratedcircuit #clock #timing #oscillator