Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Lethal Company Pro Flashlight Broken Features: - U2M cannot be line powered from this circuit so the LED driver does not regulate. [Find the acompanying button board here](https://www.flux.ai/markwuflux/lethal-company-pro-flashlight-button-board) -Ultra bright -Makes click noise from speaker -Wirelessly transmits battery life (maybe use Ubo to receive this) -Drive a SST-40 Chinese LED I want this thing to be super bright! The brighter the better, but keep it simple. These LEDs will draw a lot of power, so we need some sort of CC source. It doesn't have to have high bandwidth. I am thinking about a DIY microcontroller buck converter with PID duty cycle control. Mistakes in this V1 design: - No pullup resistor on PG of Module1

It's dangerous to go alone... take this!

Designing a Tractive System Active light(TSAL) circuit for an Electric Vehicle which does the following operations 1. The TSAL itself must have a red light, flashing continuously with a frequency between 2 Hz and 5 Hz and a duty cycle of 50%, active if and only if the LVS is active and the voltage across DC-link capacitors exceeds half the nominal TS voltage 2. The TSAL itself must have a green light, continuously on, active if and only if the LVS is active and ALL of the following conditions are true: ● All AIRs are opened. ● The pre-charge relay is opened. ● The voltage at the vehicle side of the AIRs inside the TSAC does not exceed 60 VDC or 50 VAC RMS. This schematic will include only the Green Light logic. We have to take proper care of High voltage and Low voltage isolation in this schematic because it will have to be implemented on the PCB as well.

Cost-Effective USB-C 2S Li-Ion Charger with Integrated 1W LED Flashlight - Fully Discrete, Generic Components, Minimalist Design

Hand-sized pumpkin PCB The copper has been removed at the eyes and mouth so light can shine through from the back! 555 Timer has been selected to provide LED flashing at 0.5Hz Adjust R2 for differing speed!

Welcome to your new project. Imagine what you can build here.

Fast USB-C thumb-drive carrier for a managed solder-down USB 3.x flash module, targeting permanently attached 128 GB, 256 GB, or 512 GB storage.

Xiaomi 8 Type-C OTG Hub with Flash Mode

IC FLASH 256MBIT SPI

Welcome to your new project. Imagine what you can build here.

Use this template if you're planning to get your 1 to 2-layer board manufactured in JLCPCB. It has the via min/max and trace width constraints already baked as global rules. #project-template #template #manufacturer-design-rules

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

This bee hotel version is an intermediary version that implements some featuresets. The main feature that we are leaving out is Matter support over Zigbee (for a wider range in the backyard). In this version, we are implmenting: -Legacy WiFi/BT connectivity. -Camera with flash capability -Solar Charging -Energy Storage -Humidity and Temp Sensor

Here's a template for the popular ESP-8266EX microcontroller board, wemos D1 mini. A mini wifi board with 4MB flash based on ESP-8266EX #wemos #esp8266 #project-template #template

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

µGame is a game console that is programmable with Python. To get a fully functional device, you will need to compile and flash the UF2 bootloader and the special CircuitPython firmware. Instructions for that will be posted separately.

Here's a template for the popular ESP-8266EX microcontroller board, wemos D1 mini. A mini wifi board with 4MB flash based on ESP-8266EX #wemos #esp8266 #project-template #template

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR