Welcome to your new project. Imagine what you can build here.

A board to use any PWM output with a 3 pin header

Changelog/TODO: -Breakout the SPI Bus in a 2.54mm header in a snap off manner -add an IMU -Reorder the rows of the LEDs -Create an external USB-C UART programmer to provide programming and power Tutorials: https://circuitdigest.com/microcontroller-projects/interfacing-max7219-led-dot-matrix-display-with-arduino

This is an office productivity hub featuring an STM32F103C8T6 MCU, GC9A01A display driver, voltage regulator, capacitors, resistors, switches, USB-C, and SWD header. #referenceDesign #edge-computing #edgeComputing #stm #template #iot #stm32f1 #reference-design

Through Hole straight pin header, 02x06, 2.54mm pitch, double row #pinheader #tht #simplifiedFootprint

Low-voltage logic-only CERILUME Phase 1 LED controller using an Arduino Nano ESP32 plug-in module, 5V logic level shifting for WS2812/SK6812 data, microphone input header, and labeled test pads. LED power distribution and high-current switching are intentionally out of scope.

Mini Paper USV PCB Upgrade v1.0 schematic twin using an ELEGOO MEGA 2560, L293D H-bridge, HC-SR04 ultrasonic sensor, SG90 servo header, LED indicators, buzzer, and dual 9V parallel battery input.

This module involves the design of a keypad lock system. It utilizes an ATMEGA328P microcontroller, buzzers, LEDs for indicator functions and a 4x3 matrix keypad. An in-circuit serial programming (ISP) header is also present for programming the microcontroller. #template #lock #keypad #reusable #module #simple-embedded #microchip #arduino #atmega328 #TPS613222A #ISP #buzzer #sublayout

Connector Header Surface Mount 2 position 0.049" (1.25mm)

Connector Header Surface Mount 2 position 0.049" (1.25mm)

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #attiny2313 #TPS613222A #ISP #buzzer #reusable #module #simple-embedded #microchip #arduino #sublayout

Through hole straight pin header, 1x04, 4 pin, 4-pin, horizontal, angled, 2.54mm pitch, 6mm pin lenght single row

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #arduino #attiny2313 #TPS613222A #ISP #buzzer #referenceDesign #simple-embedded #microchip #template #reference-design

An I2C extension shield with 6 shielded ethernet ports and a TCA9548 breakout board. This board is for the target side, any microcontroller with a standard Arduino header can use it. With proper target side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The shield board provides power to the target side and can power the i2c device. The board also supports drdy trigger, which is available on many i2c sensors. The TCA9548 breakout board is for a scenario in which all of your i2c devices have the same address. #Arduino #Uno #Shield #Template #project-template #project

Important Note: You must connect your own SPI/ICSP programming header if you want to burn the Arduino bootloader to the MCU. SMD Manufacturing: Need a hotplate and solderpaste Good to haves: - Oscillator Decoupling Caps Expose UART via connector Programming Button Onboard LED Reset Button You don't have to populate everything! Only these are mandatory: Reset Button Find the reference schematic here: https://www.arduino.cc/en/uploads/Main/ArduinoNano30Schematic.pdf

Connector Header Through Hole 2 position 0.079" (2.00mm) 01x02 JST B2B PH K

Raspberry Pi 5 HAT with 12V DC input protection, 12V-to-5V buck regulation, 40-pin GPIO header, MPU6050 I2C header, NEO-8M UART header, and GPIO status LED.

Compact USB-C powered desktop CO2 monitor using an RP2040, Sensirion SCD30 NDIR sensor, 3.3V I2C OLED header, and RGB air-quality indication, with native USB boot and SWD debug.

USB-C powered ESP32 WiFi water-flow-meter controller for an external 12V RS485 ultrasonic sensor on 3/4 inch PVC pipe, with protected power input, 3.3V logic rail, 12V boost rail, programming header, reset/boot controls, and status LEDs.

Breadboard adapter for the Moddo pinch: a 2×8 1.27 mm through-hole center header broken out to 2.54 mm through-hole headers on an 18 × 15 mm, 2-layer PCB.

Small breadboard-friendly breakout/carrier PCB for the Moddo pinch SAMD11 dev board, converting its 16-pin 1.27 mm header to 2.54 mm through-hole breakout pins. Mechanical dimensions are marked verify-against-hardware until Moddo publishes official drawings.

DeskNeuron V0.1 — USB-C ESP32-S3 6-key macro pad with dual EC11 encoders and SPI TFT header.

Raspberry Pi Zero HAT-style PCB with bottom 40-pin GPIO header and top-side connectors for MLX90640 thermal camera, SCD41, PIR, IMU, OLED, and thermal sensor terminals.

Battery-powered infrared/PIR sensor board with USB-C charging, single-cell LiPo battery input, 3.3 V regulation, sensor output header, and status indicators.

Arduino Mega 2560 sensor/actuator interface shield for a firefighting differential robot with labeled connectors, onboard IR receiver, buzzer, MPU6050 header, battery VIN protection, battery sensing, LED outputs, and fan MOSFET control.