ZED-X20P-00B Part Audit
Sources
Metadata review
- MPN: ZED-X20P-00B — matches.
- Manufacturer property: u-blox — matches; library manufacturer facet currently displays
Other.
- Package: LGA module, nominal 22.0 x 17.0 x 2.4 mm — footprint body and pad locations are consistent with the official mechanical information.
- Physical lands: 54 numbered perimeter pads plus 48 central exposed ground lands = 102 solderable lands. The 102-terminal count is therefore mechanically valid, although only pins 1–54 appear in the electrical pin table.
- Datasheet URL was already present and points to the official u-blox PDF; no URL update was required.
Key specifications
- GNSS: all-band high-precision receiver supporting GPS, Galileo, BeiDou, QZSS and related signals.
- VCC operating range: 2.7–3.6 V, 3.0 V typical.
- V_BCKP: 1.65–3.6 V; typical backup current 32 uA.
- Operating temperature: -40 to +85 degC.
- RF input impedance: 50 ohm.
- VCC_RF output: up to VCC - 0.1 V, 50 mA operating maximum.
- Typical current: 68 mA acquisition and 64 mA tracking for GPS+GAL+BDS; 80 mA peak acquisition.
- Interfaces: UART1/SPI/I2C multiplexed host interface, UART2, USB, timepulse, external interrupt and status outputs.
Symbol organization applied
All 102 terminals were preserved in place without renaming, renumbering, replacement, or footprint remapping. Pin Group was removed from every terminal. Each terminal now has a Section, Left/Right Pin Orientation, and globally unique consecutive Terminal Order.
Section/order ranges:
- Power: orders 1–5, Left/Right 3/2
- RF & Antenna Control: 6–9, 2/2
- UART2: 10–11, 1/1
- USB: 12–13, 1/1
- Host Interface: 14–18, 3/2
- Status, Timing & Control: 19–25, 3/4
- Reserved: 26–46, 11/10
- Ground: 47–102, 28/28
Verification confirmed pin numbers 1–102 remain present exactly once, Power is first, Ground is last, no Pin Group or sub-symbol suffix remains, and all terminal orders are unique and consecutive.
Mismatches / quality flags
- Pins 38–40 have incorrect terminal names in the current symbol and were deliberately not renamed due to the preservation constraint:
- Pin 38 is named
RESERVED_20; datasheet name is VDD_USB (USB supply input).
- Pin 39 is named
RESERVED_21; datasheet name is USB_DM (USB data I/O).
- Pin 40 is named
RESERVED_22; datasheet name is USB_DP (USB data I/O).
- All terminals currently have
Pin Type: Unspecified; datasheet I/O/power/ground types are not represented.
- Pin Description is absent across the symbol despite the datasheet providing descriptions for pins 1–54.
- Central pads 55–102 are labeled
EP_1 through EP_48; the integration manual identifies these as exposed ground lands. Their Ground section assignment is correct, but their Pin Type remains Unspecified.
- The project description states an upper operating temperature of +105 degC; the official R05 datasheet specifies +85 degC operating maximum and +85 degC storage maximum.
- The part-level
Part Type property is blank and the library manufacturer facet reports Other, despite Manufacturer Name being u-blox.
- The footprint copper geometry substantially matches the suggested footprint: 0.8 x 1.5 mm perimeter lands at 1.1 mm pitch and 1.1 x 1.1 mm central lands at 2.1 mm pitch. A dedicated 23.0 x 17.4 mm component keepout and explicit ground-via guidance are not encoded in the footprint.
Preview limitation
The structured symbol properties verify the organization. The raster schematic preview rendered blank/text-incomplete for this unusually large 102-terminal part, so visual symmetry was validated using the exact Left/Right counts and ordered property table rather than the raster image alone.