STBC08PMR Review


I’ll inspect the part metadata, look for an official datasheet if needed, update the Datasheet property if missing, then compare symbol/footprint/pin info against the datasheet and summarize any mismatches.
I found the official ST datasheet and updated the part project’s Datasheet URL property. I’m now checking the symbol and footprint details against the datasheet.
Created a project doc

STBC08PMR Part Review

View Document

Date: 2026-07-17 Reviewed the published Flux part project for STBC08PMR against the official STMicroelectronics datasheet and available proj...
Done — I added the official ST datasheet URL and created the detailed review in STBC08PMR Part Review.
Open items flagged:
  • Missing/weak metadata: empty Part Type, poor description, no pin descriptions.
  • Symbol issues: POWER_ON and CHRG should be open-drain outputs; exposed pad should not be modeled as mandatory Power In.
  • Footprint concern: side pads appear to be an IPC variant, but the exposed-pad copper does not clearly match ST’s recommended land pattern.
Suggested next steps:
  1. Update the part metadata and pin descriptions.
  2. Correct the open-drain/status pin types.
  3. Rework or explicitly document the footprint deviation from ST Figure 16.
Fix issues and review
Fix flagged issues
Use ST footprint
Document IPC deviation
Run review again

STBC08PMR Part Review
Date: 2026-07-17
Scope
Reviewed the published Flux part project for STBC08PMR against the official STMicroelectronics datasheet and available project metadata, schematic terminals, and PCB footprint data.
Current part information in Flux

Table


FieldCurrent valueReview
Manufacturer Part NumberSTBC08PMRMatches datasheet order code.
Manufacturer NameSTMicroelectronicsMatches datasheet.
Datasheet URLhttps://www.st.com/resource/en/datasheet/stbc08.pdfAdded during this review.
Part TypeEmptyMissing; should be set to a battery charger / power-management IC category.
Designator PrefixUAppropriate for an IC.
Description4 / STMicroelectronics / 1.00mm / IPC-7351BNot descriptive; should state function, package, and main rating.
Terminal count7Correct if the exposed pad is modeled as pin/pad 7.
Footprint nameSON95P300X300X100-7NMechanically related, but datasheet names the package DFN6 / VFDFPN 6, 3 x 3 mm.
Datasheet key specs

Table


ParameterDatasheet value
Function800 mA standalone linear Li-Ion battery charger with thermal regulation
Order codeSTBC08PMR
PackageDFN6 / VFDFPN 6, 3 x 3 mm
Input supply, recommended/electrical characteristic4.25 V to 6.5 V
Input supply, absolute maximum-0.3 V to 10 V
Battery pin absolute maximum-0.3 V to 7 V
Regulated battery voltage4.2 V typical; 4.158 V min, 4.242 V max
Maximum charge currentUp to 800 mA
Programmed charge current examplesRPROG = 10 kΩ -> 100 mA typ.; RPROG = 2 kΩ -> 500 mA typ.
Charge-current programmingIBAT = VPROG / RPROG x 1000; RPROG is 1% to GND
Pre-charge threshold2.8 V min, 2.9 V typ., 3.0 V max
Operating junction temperature-40 °C to 85 °C
Maximum junction temperature125 °C
Required/recommended external components1 µF bypass capacitor on VCC; RPROG from PROG to GND; BAT capacitor guidance if battery lead inductance or disconnected-battery ripple is a concern
Status pinsPOWER ON and CHRG are open-drain status outputs and require pull-ups for logic-high indication
Datasheet pinout vs current symbol

Table


PinDatasheet name/functionCurrent Flux terminalCurrent pin typeReview
1BAT — battery charge output / 4.2 V regulation outputBATOutputAcceptable; Power Out would also be reasonable.
2POWER ON — open-drain input-power-valid/status outputPOWER_ONBi-DirectionalMismatch. Should be open-drain output / output-like, not bidirectional logic.
3CHRG — open-drain charge-status outputCHRGBi-DirectionalMismatch. Should be open-drain output / output-like, not bidirectional logic.
4GND — groundGNDPower InAcceptable by many IC-symbol conventions, though a Ground type would be clearer if available.
5PROG — charge-current program, monitor, shutdown controlPROGBi-DirectionalMinor issue. Multifunction analog pin; Input, Passive, or analog/signal would communicate intent better than generic bidirectional.
6VCC — input supply voltageVCCPower InCorrect.
7Exposed pad — connected to GND or left floatingEXPPower InMismatch / misleading. It is not a required independent power input; should be optional GND thermal pad or passive/ground pad with description.
Pin-description finding
The terminal names and pin numbers are mostly correct, but the project does not include explicit Pin Description text for the pins. Adding the datasheet descriptions would improve library quality and downstream schematic review.
Footprint cross-check
Datasheet package / land-pattern data

Table


FeatureDatasheet value
Package body3.0 x 3.0 mm nominal; 2.90 to 3.10 mm tolerance
Pin pitch0.95 mm
Lead width, package mechanical b0.23 to 0.45 mm
Lead length, package mechanical L0.30 to 0.50 mm
Exposed paddle mechanical D22.23 to 2.50 mm
Exposed paddle mechanical E21.50 to 1.75 mm
ST recommended lead pads0.45 x 0.50 mm, 6x
ST recommended exposed pad2.50 x 1.75 mm
Current footprint data

Table


FeatureCurrent footprintReview
Pitch0.95 mmMatches datasheet.
Fab/body outline3.10 x 3.10 mmAcceptable; corresponds to package maximum.
Side pads0.86 x 0.40 mm at x = +/-1.435 mm, y = -0.95/0/+0.95 mmDeviates from ST recommended 0.45 x 0.50 mm. This may be an IPC-7351B toe-extension variant, but it is not the ST nominal land pattern; width is slightly narrow and length is much longer.
Exposed pad copper1.625 x 2.365 mmMain footprint concern. This does not directly match ST recommended 2.50 x 1.75 mm and may be transposed/axis-mismatched or based on mechanical paddle size rather than recommended copper land. Verify orientation before accepting.
Exposed-pad pasteSingle paste aperture about 1.0276 x 1.4958 mmReduced paste coverage is not inherently wrong for thermal pads, but should be reviewed after the exposed-pad copper geometry is corrected/confirmed.
Pad count7 total padsCorrect, including exposed pad.
Mismatches / quality issues to flag
  1. Missing descriptive metadata — Part Type is empty and the description does not describe the device function.
  2. Pin descriptions are absent — pin names/numbers are present, but Pin Description properties are not populated from the datasheet.
  3. POWER_ON and CHRG pin types are wrong — both are open-drain status outputs, not bidirectional pins.
  4. Exposed pad type is misleading — pin 7 can be tied to GND or left floating; it should not be modeled as a mandatory Power In pin without an optional-ground/thermal-pad note.
  5. Footprint side pads are not the ST recommended land pattern — current side pads appear to be an IPC-7351B variant with long toe extension; acceptable only if intentionally using IPC land pattern rather than ST's recommended footprint.
  6. Exposed pad copper geometry needs verification — current 1.625 x 2.365 mm does not clearly match ST recommended 2.50 x 1.75 mm; this is the highest-priority footprint issue because exposed-pad soldering and thermal transfer matter for a linear charger with thermal regulation.
  1. Set Part Type to a power-management / battery-charger IC category.
  2. Replace the short description with: 800 mA standalone linear Li-Ion battery charger with thermal regulation, DFN6/VFDFPN 3 x 3 mm.
  3. Add datasheet pin descriptions for all seven terminals.
  4. Change POWER_ON and CHRG pin types to open-drain output / output-like.
  5. Change EXP pin type/description to optional exposed GND thermal pad.
  6. Re-check the footprint against ST Figure 16; either adopt the ST recommended land pattern or explicitly keep the IPC-7351B variant and document the deviation.
  • Scope

  • Current part information in Flux

  • Datasheet key specs

  • Datasheet pinout vs current symbol

  • Pin-description finding

  • Footprint cross-check

  • Datasheet package / land-pattern data

  • Current footprint data

  • Mismatches / quality issues to flag

  • Recommended fixes