Terminal Block Guide


I’ll research this terminal-block header’s manufacturer specifications, mating requirements, and alternatives, then save a cited Application & Usage Guide in the project files.
I confirmed the manufacturer’s electrical ratings and found two manufacturer-documented functional alternatives, but neither is verified as a drop-in replacement. The guide will flag the unverified drill dimensions, physical pin orientation, and exact mating-plug part number rather than guess.
Created a project doc

MX2EDGR-5.08-02P-GN01-Cu-A Application and Usage Guide

View Document

MX2EDGR-5.08-02P-GN01-Cu-A Application and Usage Guide
The MAX / Cixi Maixu MX2EDGR-5.08-02P-GN01-Cu-A is a two-position, 5.08 mm-pitch, right-angle through-hole pluggable terminal-block header for detachable board-to-wire connections (LCSC product listing). A common application is a removable two-wire DC power input or output on a controller PCB, with the cable terminated in a separately purchased, manufacturer-confirmed mating plug.
1. Quick Specifications
Connector working ratings are not semiconductor-style absolute maximum ratings. The source drawing lists UL/IEC ratings and an operating-temperature range, but does not supply a separate absolute-maximum table,...
Created the cited Application & Usage Guide in the project files, covering all seven requested sections. It distinguishes rated limits from test conditions, provides practical wiring and layout guidance, and labels both alternatives as functionally similar—not verified drop-ins. Exact mating-plug identification, physical pin orientation, and drill dimensions remain explicitly unverified.

MX2EDGR-5.08-02P-GN01-Cu-A Application and Usage Guide
The MAX / Cixi Maixu MX2EDGR-5.08-02P-GN01-Cu-A is a two-position, 5.08 mm-pitch, right-angle through-hole pluggable terminal-block header for detachable board-to-wire connections (LCSC product listing). A common application is a removable two-wire DC power input or output on a controller PCB, with the cable terminated in a separately purchased, manufacturer-confirmed mating plug.
1. Quick Specifications
Connector working ratings are not semiconductor-style absolute maximum ratings. The source drawing lists UL/IEC ratings and an operating-temperature range, but does not supply a separate absolute-maximum table, recommended nominal operating point, or current-versus-temperature derating curve; do not interpret the following as permission to operate every limit simultaneously.

Table


ParameterValueClassification / conditions
ManufacturerCIXI MAIXU ELECTRONICS CO., LTD.; sold under MAXDrawing title block identifies the manufacturer.
Positions / pitch2 positions; 5.08 mmExact orderable variant is confirmed by the LCSC listing; the drawing covers 02–24 positions.
UL voltage / current300 V / 15 AManufacturer-listed rating, not a separately specified absolute maximum.
IEC voltage / current320 V / 15 APollution degree 2, overvoltage category III; rated impulse voltage 4.0 kV.
Withstand voltageAC 2000 V for 1 minuteInsulation test condition, not continuous working voltage.
Operating temperature−40 °C to +105 °CStated operating range; current derating at elevated temperature is unverified.
Mounting / constructionRight-angle, through-hole, one row, open header, greenDistributor-confirmed configuration; no fixing device is listed. LCSC
Housing / solder pinsPA66, UL94V-0 / tin-plated brassManufacturer material specification.
Contact resistance / solder profileNot specified in the supplied drawingObtain assembly conditions and contact-performance data from the manufacturer before production qualification.
Absolute maximum / recommended nominal conditionsNot separately specifiedSelect the actual voltage/current for the complete connector, mating plug, wire, PCB and enclosure system; do not invent a typical rating.
The drawing's UL/IEC headings do not independently establish a particular certification file or approval status for this exact ordering code. Verify applicable approvals for regulated products.
2. Pinout & Connections
This is a passive connector: neither contact has an inherent VIN, GND, enable or logic function. The following table is an example schematic assignment, not a verified left/right physical pinout; the drawing-to-library pin-number orientation was not verified. Before release, confirm symbol-to-pad-to-mating-wire continuity against an approved drawing or sample.

Table


Pin NumberPin NameDescriptionBest Practice
1 — example assignmentVIN / OUT+First contact, assigned to the positive supply in this exampleRoute through appropriately selected input protection; mark + and the actual operating voltage on the PCB and cable. Verify physical contact mapping.
2 — example assignmentRETURN / OUT−Second contact, assigned to supply return in this exampleConnect to the intended power-return net; tie to GND only when the system architecture actually uses grounded return. Verify physical contact mapping.
For an isolated output or two-wire signal interface, rename both nets to match the circuit rather than assuming contact 2 is GND. No pull-up, pull-down, bias resistor or decoupling capacitor is intrinsically required by the connector.
3. Standard Application Circuit
Two-wire DC power-input connection

Text


External DC source + --> confirmed mating plug --> J1 contact 1
    --> fuse/current limiter --> reverse-polarity protection --> VIN_PROTECTED
External DC source − --> confirmed mating plug --> J1 contact 2 --> POWER_RETURN

Optional TVS: VIN_PROTECTED to POWER_RETURN
Load-required input capacitor: VIN_PROTECTED to POWER_RETURN
This is an engineering integration example, not a manufacturer reference circuit. Choose the fuse or current limiter for normal load current, inrush and the fault tolerance of the wire/connector/PCB path; the connector's 15 A rating is not a fuse-selection value. Use reverse-polarity protection when field wiring can be reversed, and select any TVS for supply tolerance, expected cable transients and downstream absolute limits.
Required passive components: none for the header itself. Protection and input capacitance depend on the connected load; there is no defensible universal capacitor value or voltage rating without the system specification. Follow the downstream regulator or load datasheet, including hot-plug inrush considerations.
Mating plug: the supplied header drawing does not identify an exact mating-plug MPN. Obtain written confirmation from MAX/Cixi Maixu or the supplier for the complete header/plug pair, then use the plug's own wire-gauge, stripping-length, ferrule and tightening-torque instructions. Do not transfer wire-clamp specifications to this board header, which does not itself clamp the wire. De-energize before mating or unmating unless the complete connector pair is explicitly approved for switching under load; such approval was not verified.
4. PCB Layout & Routing Guidelines
The following are engineering layout recommendations; they are not undocumented manufacturer dimensions.
  • Footprint and drill verification: use the verified 5.08 mm pitch, but obtain the approved hole pattern, finished-hole tolerance, pin cross-section and body/board-edge dimensions before footprint release. Automated extraction returned unverified candidate drill/pin dimensions, so no drill or pad size is prescribed here. Do not reuse an alternative manufacturer's land pattern merely because the pitch matches.
  • High-current copper: size both supply and return paths using copper thickness, layer position, allowed temperature rise and actual continuous/peak current, following an IPC-2152-based method. Prefer short, broad copper regions; check pad exits, protection-device pads, plated-hole barrels and layer-transition vias for bottlenecks. The 15 A connector rating does not make a narrow PCB trace a 15 A path.
  • Thermal relief versus solderability: size plane-connection spokes for the current they carry, or use a direct connection where the qualified solder process can heat the joint adequately. Inspect through-hole solder fill and measure voltage drop/temperature rise at full load; thin default thermal spokes can be the limiting conductor.
  • Mechanical access: locate the right-angle mating face near an accessible board edge and reserve the complete plug insertion/removal envelope, cable bend space and any screwdriver access. Provide cable strain relief so repeated handling does not load the two solder joints; confirm enclosure clearance with the actual plug.
  • Spacing and input components: calculate creepage/clearance for actual working voltage, pollution degree, overvoltage category, material group and applicable safety standard—not pitch alone. Keep load-required input capacitors close to the load and any transient-protection loop short. This connector has no verified controlled-impedance specification; do not assume USB or another high-speed differential interface is suitable merely because two contacts are available.
5. Common Pitfalls / Things to Watch Out For
  1. Assuming matching pitch means a drop-in or mating-compatible connector. A two-pole 5.08 mm header can differ in pin geometry, housing envelope, polarization and insertion depth. Verify the full header/plug pair, physical pin numbering and PCB dimensions before substituting parts; wrong polarity can damage the board even if the plug appears to fit.
  2. Treating 300 V / 15 A as an unconditional system rating. The mating plug, cable termination, PCB copper, solder joints, enclosure temperature or insulation spacing may impose a lower limit. Do not use the AC 2000 V withstand test as working voltage, and do not assume the full current rating remains available at +105 °C.
No verified drop-in replacement was established. These are manufacturer-documented, functionally similar two-position 5.08 mm PCB headers; pin compatibility, footprint compatibility and cross-brand mating compatibility with the MAX part are all unverified. Their inclusion does not establish sales popularity.

Table


Manufacturer / partVerified functional similarityCompatibility and qualification action
Phoenix Contact MSTB 2,5/ 2-G-5,08 — 1759017Two positions, 5.08 mm pitch, soldered PCB header with plug-in direction parallel to the PCB; manufacturer lists nominal current 12 A and rated voltage 320 V (III/2).Functionally similar only. Not a validated 15 A replacement: recheck electrical requirements. Revalidate footprint and enclosure. Phoenix identifies its mating MSTB 2,5/ 2-ST-5,08 plug, item 1757019, on the product page; that is not evidence it mates with MAX.
Weidmüller SL 5.08HC/02/90 3.2SN OR BX — 1146720000Two-pole, 5.08 mm, 90° open-side male header, THT solder connection, 3.2 mm solder-pin length, tin finish, orange, boxed packaging.Functionally similar only. Revalidate hole geometry, body envelope, ratings and complete mating pair using Weidmüller's current documentation.
Exact-MPN and full-text Flux library searches did not locate either alternative during this review; therefore no verified Flux-library link is supplied. Manufacturer product links above are the evidence sources, not claims of library availability.
7. Sourcing & Purchasing Guide

Table


AttributeDetails
Primary DistributorsExact part listing verified at LCSC, C5187973. Exact-MPN availability at DigiKey, Mouser or Arrow, and distributor franchise status for MAX, were not verified.
Packaging OptionsLCSC lists 500 pieces / full bag on its localized product page. Tape-and-reel and cut-tape options were not verified; Through Hole, Right Angle describes mounting, not shipping packaging.
Standard MOQLCSC localized listing showed a 20-piece minimum and a 500-piece full bag at review on October 7, 2026. Reconfirm cart minimum/order multiples before purchase; the page's Custom Cables MOQ 1pc is not the header's MOQ. LCSC ordering page
Sourcing AdviceOrder the complete MX2EDGR-5.08-02P-GN01-Cu-A code / C5187973, and source the confirmed mating plug separately. Verify position count, pitch, right-angle geometry, material/finish, colour and suffix definitions with the supplier; the full suffix encoding was not verified. Prefer manufacturer-direct or manufacturer-confirmed franchised channels. Avoid untraceable marketplace stock with uncertain materials, plating or safety markings; request lot traceability and approval documentation where required. Recheck availability and MOQ at order time.
Sources
Verification boundary: electrical ratings and material statements above are supported by the supplied manufacturer drawing; exact physical pin numbering, finished-hole/pad dimensions, full body dimensions, mating-plug MPN, derating curve and assembly profile remain unresolved. This application guide does not certify the existing Flux footprint or a completed end-product design.
  • 1. Quick Specifications

  • 2. Pinout & Connections

  • 3. Standard Application Circuit

  • Two-wire DC power-input connection

  • 4. PCB Layout & Routing Guidelines

  • 5. Common Pitfalls / Things to Watch Out For

  • 6. Popular Alternatives & Equivalents

  • 7. Sourcing & Purchasing Guide

  • Sources