Part Audit Report


Review all available part information (MPN, package, pin count, description, properties). If no datasheet URL is already set, search the web for the official datasheet and update the part's Datasheet property with the URL. Then cross-check the schematic symbol, footprint, and pin descriptions against the datasheet. Summarize key specs and flag any mismatches.
I’ll audit the part metadata, obtain the official datasheet if needed, compare the symbol and 200-pad footprint against it, update the Datasheet property, and document any mismatches.
The part is modeled as 200 terminal objects, so I’m performing an exhaustive pin/ball audit rather than sampling.
Audit complete. The 200-ball symbol map and 0.80 × 0.65 mm footprint geometry match the Micron datasheet; the Datasheet URL was already populated, so it was not changed. Key issues are incorrect package/mount metadata and missing Pin Type/Pin Description data for all 200 terminals.
Full findings: Part Audit Report
Fix part metadata
Attach revision-C source
Review BGA manufacturability
Prepare LPDDR4X guidance

Footprint Pitch Correction
Final verification reconciliation
A separate read-only check confirmed 200 terminals and 200 pad nodes but could not independently retrieve evaluated pad coordinates or a readable WT:C-specific datasheet. It therefore did not independently approve geometry; it established no conflicting measured pitch or mapping error. The measurements below rely on the stored footprint and fresh native export described in this report, not the coordinate-free scene tree. No footprint changes were made. Exact WT:C qualification and a manufacturer PCB land recommendation remain open; this is not a manufacturing-release approval.
Outcome and scope
2026-10-12: No footprint correction was necessary. Both the stored footprint source and a fresh export of the current part already implement 0.80 mm numbered-column pitch × 0.65 mm letter-row pitch. No pad, rule, symbol, pin mapping, metadata, model or asset was changed. Only this project file was created. No duplicate internal quality report was filed.
Completed: metadata/document inspection, source drawing inspection, all-200 source-position comparison, all-200 current exported-position/signal comparison, preservation assessment and this report. Conditional geometry correction: completed as a no-op because no sourced discrepancy exists. Exact WT:C revision qualification remains unresolved; unrelated metadata/symbol remediation and publication were unattempted and outside scope.
Sources and verification limits
Evidence status: Direct PDF text extraction and visual inspection were completed. Immutable datasheet citation processing timed out and remains unresolved; no validated flux:cite identifiers were returned. Datasheet-derived observations below are manually checked against the identified pages, but are unverified by the automated citation service. No citation handles have been invented.
Drawing interpretation and applicability
Manual observations from Figure 10, page 30:

Table


ItemDrawing observation
PackageFW, 200-ball TFBGA
Body10.0 ±0.1 mm × 14.5 ±0.1 mm
HeightDrawing callout 1.0 ±0.1 mm; title uses 1.1 mm maximum
Numbered columns0.80 mm pitch; outer center span 8.80 mm
Letter rows0.65 mm pitch; outer center span 13.65 mm
Solder balls200 × Ø0.436 ±0.05 mm, dimensions apply post-reflow on Ø0.40 SMD ball pads
PCB copper land recommendationNot established by this package-dimension callout alone; no separate PCB land-pattern/assembly recommendation obtained
The array drawing in Figure 10 is a ball-side/bottom view: A1 is at upper right, and numbers run 12→1 left-to-right. Its adjacent package top view places the A1 mark upper left. Figure 6 explicitly states “Top View (ball down)”: A1 upper left, numbers increasing left-to-right and letters increasing downward. The existing top-side footprint follows Figure 6, not an unmirrored copy of the bottom-view drawing.
The full row-index sequence is A B C D E F G H J K L M N P R T U V W Y AA AB. Rows L/M are empty; columns 6/7 are empty. Thus 22×12 nominal sites minus 64 absent sites gives 200 actual balls. The skipped alphabet letters are naming conventions, not additional physical grid intervals.
Warning — revision applicability: Table 2 explicitly lists MT53E1G32D2FW-046 WT:B, not WT:C. FW package code, dual-rank ball count and this project's existing geometry are consistent with the attached drawing, but an exact C-revision datasheet or Micron PCN establishing B→C package/ball-map equivalence was not obtained. Do not treat this review as revision-C electrical or mechanical release qualification.
Before / after measurements
No geometry edit was made; before and after are identical. Coordinates below are footprint-local Flux coordinates (X right, Y up), with the origin at array center.

Table


MeasurementBeforeAfter
X pitch, increasing ball number+0.800 mm+0.800 mm
Y step, increasing row index−0.650 mm−0.650 mm
X center bounds−4.400…+4.400 mmunchanged
Y center bounds−6.825…+6.825 mmunchanged
Outer center spans X×Y8.800×13.650 mmunchanged
Source circular copper pad diameter0.399 mm, all 200unchanged
Source-derived outer copper spans X×Y9.199×14.049 mmunchanged
Central gap: column 5→8 centers2.400 mmunchanged
Central gap: row K→N centers1.950 mmunchanged
For zero-based row index r in the full sequence and column number c, the checked coordinate rule was:
X = (c − 6.5) × 0.80 mm
Y = (10.5 − r) × 0.65 mm
A1 = (−4.400,+6.825); A12 = (+4.400,+6.825); AB1 = (−4.400,−6.825); AB12 = (+4.400,−6.825). KiCad source/export Y has the opposite sign because its local drawing coordinates are Y-down. This is a coordinate convention, not a footprint mirror.
Exhaustive checks and preservation
  • Read all 200 pad UIDs/designators through the scene tree and all 200 terminal properties including Pin Number, Section, Terminal Order, Symbol Pin Position and Pin Orientation through schematic inspection.
  • Parsed every pad in the stored footprint: 200 unique ball numbers, 200 unique positions; 200/200 exactly match the indexed expected coordinates at the source's decimal precision.
  • Parsed a fresh native runtime export: 200 unique pad signal names, 200 unique positions; zero missing/extra positions and zero signal-to-position mismatches against Figure 6. Repeated power/ground/NC/DNU designator suffixes were normalized only in the comparison script, never in the project. Differential suffix case was normalized to the existing uppercase convention.
  • Confirmed the complete empty-row/empty-column pattern and no duplicate centers. A1 orientation is consistent with the retained upper-left silkscreen index mark.
  • Original 200 pad UIDs, ball numbers, pin mappings and symbol organization were preserved by making no geometry/schematic mutation at all. The footprint source contains 0.399 mm circular F.Cu/F.Paste/F.Mask pads; no pad-size justification was found that warrants changing them.
  • Direct layout scene inspection does not expose this imported footprint's runtime pad dimensions/positions, and its 2D view omitted the pads. Therefore exact coordinate validation used the stored source plus a fresh native export rather than pretending the scene tree had measured coordinates.
  • The runtime exporter represents copper as polygons plus zero-size custom pad anchors; anchor coordinates were useful for position checking, but those placeholder sizes were not interpreted as actual copper sizes. No manufacturing export qualification is claimed.
  • Requested invalid-pad, invalid-layer and terminal-pin-number checks returned “No ERC/DRC Reviews match the filter.” This is not a clean-DRC assertion; the decisive evidence is the exhaustive coordinate comparison.
Stored footprint SHA-256: 98f265bde8f5e16be086cd9fdcdbf0c25cd7f63bdc0723482ac6e61b40514cd4.
Reconciliation with prior claims
The footprint asset's name contains 65P, but its coordinates explicitly use two different pitches. A claim of 0.65 mm on both axes is incorrect for this current project. The existing part-audit-report actually states 0.80×0.65 mm and agrees with this independent measurement. Its characterization of the package's Ø0.40 SMD ball-pad callout as a PCB land recommendation is not independently established by this review.

fw-package

  • Final verification reconciliation

  • Outcome and scope

  • Sources and verification limits

  • Drawing interpretation and applicability

  • Before / after measurements

  • Exhaustive checks and preservation

  • Reconciliation with prior claims