Part Audit Report


Created a project doc

Part Audit Report

View Document

Part Audit Report Scope
Audit of IS25WX512M-JHLE against the official ISSI datasheet: (Rev. 0D, 2024-05-16). Datasheet extraction was OCR-assisted because the manufacturer PDF intermittently returned HTTP 403; critical package and pin-map findings were cross-checked across the ordering table, ball-assignment table, and current Flux footprint.
Current part information Key specifications
  • Memory: 512 Mbit / 64 Mbyte serial NOR flash with on-chip ECC.
  • Interface: JEDEC xSPI; Extended SPI and Octal DDR (8D-8D-8D).
  • Supply: 1.70–2.00 V for the IS25WX family.
  • Maximum clock: 166 MHz SDR and 200 MHz DDR / Octal DDR for IS25WX.
  • Temperature code E: -40°C to +105°C.
Audit complete. The official ISSI datasheet URL was already set, and all 24 ball assignments plus the 6 × 8 mm, 1.00 mm-pitch TFBGA footprint structure match.
Key issues: incorrect Logic/AND classification, all pin types set to Unspecified, missing pin descriptions, and the 0.37 mm pad diameter remains unverified. Full specs and findings are in Part Audit Report.
Correct the classification, pin types, pin descriptions, and ambiguous temperature wording from the audit.
I’ll correct the part classification and temperature wording, then assign datasheet-aligned electrical types and descriptions to all 24 terminals and verify the result.
Corrected and verified:
  • Classification set to Memory; erroneous Logic Function: AND removed.
  • Temperature wording changed to extended temperature −40°C to +105°C.
  • All 24 pins now have canonical electrical types and datasheet-aligned descriptions.
  • Updated the Part Audit Report with the resolution status.
The previously noted 0.37 mm footprint-land verification remains open.
Verify footprint lands
Check 3D alignment
Improve symbol layout
Review production readiness

Part Audit Report
Scope
Audit of IS25WX512M-JHLE against the official ISSI datasheet: (Rev. 0D, 2024-05-16). Datasheet extraction was OCR-assisted because the manufacturer PDF intermittently returned HTTP 403; critical package and pin-map findings were cross-checked across the ordering table, ball-assignment table, and current Flux footprint.
Current part information

Table


FieldCurrent valueAssessment
Manufacturer part numberIS25WX512M-JHLECorrect
ManufacturerIntegrated Silicon Solution Inc.Correct property; library facet categorizes manufacturer as “Other,” which is a metadata inconsistency
DescriptionNOR Flash 512Mb, Octal Flash, 1.8V, 24-ball TFBGA, RoHS, ITFunctionally correct; “IT” is ambiguous and should preferably be written as extended temperature, -40°C to +105°C
Part typeIntegrated CircuitsBroad but acceptable
IC subtype / logic functionLogic / ANDIncorrect for a serial NOR flash memory
Designator prefixICAcceptable
ComplianceRoHSCorrect; ordering code L also denotes green, halogen-free and TSCA-compliant packaging
Datasheet URLhttps://www.issi.com/WW/pdf/25LX-WX512M.pdfAlready set to the official ISSI datasheet; no update required
Terminal count24Correct
PackageH option: 24-ball TFBGA, 6 × 8 mm, 5 × 5 ball gridCorrect
Footprint assetBGA24C100P5X5_600X800X120.kicad_modConsistent with 1.00 mm pitch, 5 × 5 grid, 6 × 8 mm body and nominal 1.20 mm height
Key specifications
  • Memory: 512 Mbit / 64 Mbyte serial NOR flash with on-chip ECC.
  • Interface: JEDEC xSPI; Extended SPI and Octal DDR (8D-8D-8D).
  • Supply: 1.70–2.00 V for the IS25WX family.
  • Maximum clock: 166 MHz SDR and 200 MHz DDR / Octal DDR for IS25WX.
  • Temperature code E: -40°C to +105°C.
  • Endurance: more than 100,000 program/erase cycles.
  • Retention: more than 100 years.
  • Standby / deep-power-down current: 20 µA / 2 µA headline values.
  • Ordering code: J = default Extended SPI mode; H = 24-ball TFBGA; L = green/RoHS/halogen-free/TSCA-compliant; E = extended temperature.
Ball-map cross-check
All 24 current terminal-to-ball assignments match the datasheet.

Table


BallDatasheet functionCurrent symbol/padResult
A2RFURFU_1Match
A3RFURFU_2Match
A4RESET#RESET#Match
A5ERR#ERR#Match
B1RFURFU_3Match
B2CCMatch
B3VSSVSSMatch
B4VCCVCCMatch
B5DNU / optional PSCDNU(PSC)Match
C1VSSQVSSQ_1Match
C2S#S#Match
C3DQSDQSMatch
C4DQ2 / W#DQ2/W#Match
C5VPP / optional dedicated W#VPP(W#)Match
D1VCCQVCCQ_1Match
D2DQ1DQ1Match
D3DQ0DQ0Match
D4DQ3DQ3Match
D5DQ4DQ4Match
E1DQ7DQ7Match
E2DQ6DQ6Match
E3DQ5DQ5Match
E4VCCQVCCQ_2Match
E5VSSQVSSQ_2Match
Symbol and pin-description findings
Mismatch: all electrical pin types are unspecified
Every terminal currently has Pin Type = Unspecified. Recommended datasheet-aligned types:
  • Inputs: C, S#, RESET#, PSC when that option is fitted.
  • Bidirectional: DQ0–DQ7, including DQ2/W#.
  • Output: DQS; ERR# is an open-drain output.
  • Power: VCC, VCCQ, VPP.
  • Ground: VSS, VSSQ.
  • Passive / no-connect guidance: RFU and DNU should be left floating.
Mismatch: pin descriptions are absent
No current terminals contain a Pin Description property. Important descriptions that should be added include:
  • RFU and DNU: must be left floating.
  • ERR#: ECC event indication, open drain, requires an external pull-up if used.
  • RESET#: active-low hardware reset with internal pull-up.
  • DQ[7:0]: bidirectional command/address/data bus; DQ2 also provides write-protect behavior in applicable modes.
  • DQS: read data strobe output.
  • VPP: optional high-voltage program supply; may be left floating when unused because it is internally pulled to VCC.
  • VCC/VSS: core supply/ground; VCCQ/VSSQ: I/O supply/ground.
Naming note
Suffixes such as RFU_1, VCCQ_1 and VSSQ_1 are reasonable unique symbol identifiers, but the visible pin name should remain the datasheet symbol while the ball number distinguishes duplicates.
Footprint findings
  • Exactly 24 pads are present at the correct populated coordinates of a 5 × 5, 1.00 mm-pitch grid; A1 is intentionally absent.
  • The package body drawing is 6 × 8 mm and the pin-1 indicator is located at the A-row/1-column corner, consistent with the package code.
  • Circular solder pads are 0.37 mm diameter. The fetched datasheet evidence did not expose a manufacturer recommended PCB land-pattern diameter, so this exact pad size remains not independently verified.
  • The footprint name encodes 1.20 mm height and the attached STEP model is named for the exact MPN. Model-to-pad seating was not dimensionally verified in this audit.
  1. Incorrect classification: change IC subtype from Logic to Memory / Flash and remove the erroneous AND logic function.
  2. Missing pin typing: replace Unspecified types with input, bidirectional, output/open-drain, power, ground, or passive/no-connect as appropriate.
  3. Missing pin descriptions: add datasheet-derived functional and handling descriptions to all terminals.
  4. Manufacturer indexing inconsistency: the explicit Manufacturer Name is correct, but the library search facet reports “Other.”
  5. Ambiguous description: replace “IT” with “extended temperature (-40°C to +105°C).”
  6. Unverified land pad diameter: confirm the 0.37 mm PCB pad against ISSI’s package drawing or assembly guidance before production release.
Overall assessment
The MPN, official datasheet, pin count, complete ball map, package body, pitch, and populated grid are correct. The main issues are semantic metadata quality: an incorrect Logic/AND classification, absent pin descriptions, and all terminal electrical types being unspecified. The footprint geometry appears structurally correct, with only the exact 0.37 mm land diameter requiring further manufacturer-backed verification.
Correction status
Resolved on 2026-08-24:
  • Classification changed to Memory and the erroneous Logic Function: AND property removed.
  • Operating temperature explicitly set to -40°C to +105°C and the project description updated accordingly.
  • All 24 terminal electrical types corrected using canonical Flux pin types.
  • Datasheet-aligned Pin Description properties added to all 24 terminals.
The unverified 0.37 mm PCB land diameter remains outside the scope of these corrections.
  • Scope

  • Current part information

  • Key specifications

  • Ball-map cross-check

  • Symbol and pin-description findings

  • Mismatch: all electrical pin types are unspecified

  • Mismatch: pin descriptions are absent

  • Naming note

  • Footprint findings

  • Flagged mismatches and recommended corrections

  • Overall assessment

  • Correction status