Review all available part information (MPN, packag...

Update the official datasheet URL, fix footprint drills, add pin descriptions, then run ERC/DRC.

Thought for 6 sec

I’ll update the manufacturer datasheet URL and terminal metadata, adjust the footprint drill rules to the TE recommendations, then run ERC/DRC and summarize the results.

Worked for 46 sec

flux

I found the current symbol has terminals 1–8 plus MH1–MH3, and the footprint pads are individually addressable, so I’m applying metadata and drill updates directly in-place.

Worked for 1 min 25 sec

flux

Datasheet metadata, pin descriptions/types, and drill sizes have been updated; I’m verifying the changes and running ERC/DRC now.

Worked for 3 mins 48 sec

flux

Updated the terminal metadata and footprint drill rules, then ran ERC/DRC; no open ERROR/WARNING/UNCERTAIN checks were returned. I also updated DT13-08PA Part Review with the change log and verification results.

Open items:

The official TE datasheet URL update was attempted, but the visible project Datasheet URL still resolves to the existing uploaded PDF; I flagged this as a platform/property-sync issue.

Suggested next steps:

Manually verify the Datasheet URL field in the part properties panel.
Decide whether MH1–MH3 should remain plated STD holes or be converted to mechanical/NPTH holes.

Fix datasheet and holes

Convert mounting holes

Fix datasheet property

Check manufacturability

Export review package

Files

Pins

Symbol

Layout

Preview

DT13-08PA Part Review

Review date: 2026-07-07

Sources checked

Current Flux project metadata and properties.
Current schematic terminal components and PCB footprint.
Existing project Datasheet URL: https://storage.googleapis.com/graviton-electric-symbols/document_assets/user-uploaded/9949e6057981735c112b9dbc4cf254160bed4a875dec069251116239ff8e8d4f.pdf
Official TE product page: https://www.te.com/en/product-DT13-08PA.html
Official TE data sheet: https://www.te.com/commerce/DocumentDelivery/DDEController?Action=srchrtrv&DocFormat=pdf&DocLang=English&DocNm=ict-DEUTSCH_DT-ds-a4&DocType=Data+Sheet&PartCntxt=DT13-08PA
Official TE customer drawing: https://www.te.com/commerce/DocumentDelivery/DDEController?Action=srchrtrv&DocFormat=pdf&DocLang=English&DocNm=DT13-08PX&DocType=Customer+Drawing&PartCntxt=DT13-08PA
Official TE application specification: https://www.te.com/commerce/DocumentDelivery/DDEController?Action=srchrtrv&DocFormat=pdf&DocLang=English&DocNm=114-151046&DocType=Specification+Or+Standard&PartCntxt=DT13-08PA
Official TE product specification: https://www.te.com/commerce/DocumentDelivery/DDEController?Action=srchrtrv&DocFormat=pdf&DocLang=English&DocNm=108-151009&DocType=Specification+Or+Standard&PartCntxt=DT13-08PA

The project already had a Datasheet URL set, so no automatic Datasheet property update was required by the request. However, the set URL is a user-uploaded copy rather than an official te.com URL; the official TE data sheet URL above is the preferred replacement if the library property should point directly to the manufacturer.

Current part metadata found in Flux

Table

Field	Current value
Project / part name	DT13-08PA
Published part UID	87c7f31e-a414-4571-8c87-32b7b7b4367e
Manufacturer Name	TE Connectivity
Manufacturer Part Number	DT13-08PA
Designator Prefix	J
Part Type	Connectors
Mount	PCB
Datasheet URL	User-uploaded PDF URL
Project description	Gray, key A, right-angle PCB mount, 8 positions, 2 rows, pin contacts, nickel plating, 1.59 mm mating pin diameter, 13 A max, 35.48 mm profile height; PCB thickness entry appears as `.0`
Schematic terminals	11 terminal components: 1-8 and MH1-MH3
Footprint pads	11 through-hole circular pads: 1-8 and MH1-MH3
3D model	DT13-08PA.stp referenced in layout

Key official TE specs

Table

Spec	Official value
Manufacturer / MPN	TE Connectivity / DT13-08PA
TE description	HDR, 8P, GRY, RA, NI/CU, A
Connector family	DEUTSCH DT header / receptacle assembly
Connector system	Wire-to-board
Header type	Fully shrouded rectangular PCB mount header
Positions	8 signal positions
Rows	2
Centerline / pitch	5.46 mm [.215 in]
PCB mount orientation	Right angle
PCB termination	Through-hole solder
Contact type	Pin, size 16
Mating pin diameter	1.59 mm [.063 in]
Current rating	13 A max
Voltage rating	250 VAC / 250 VDC
Key / color	A / gray
Contact mating plating	Nickel
Sealable	Yes
Operating temperature	-55 to +125 °C
UL flammability	UL 94V-0
Lifecycle	Active
Recommended PCB thickness	0.78-2.36 mm [.031-.093 in]
Connector length	39.24 mm [1.545 in]
Connector width	55.12 mm [2.170 in]
Profile height from PCB	35.48 mm [1.397 in]
Mates with	DT06-8S* plug variants

Official PCB layout / mechanical data

From TE application specification 114-151046 and drawing DT13-08PX:

Table

Feature	Official / recommended value
Signal holes	8x Ø1.88 ±0.05 mm finished hole
Signal pin diameter / tail	Ø1.56 mm [.062 in]
Signal pin pitch / layout callouts	5.46 mm [.215 in], 6.35 mm [.250 in], 14.35 mm [.565 in], plus drawing offsets
PCB mounting holes	3x Ø3.43 +0.12 / -0.00 mm recommended PCB holes
Connector-side screw holes	3x Ø2.79 mm [.110 in] thru for #4-20 screw
Pin tail projection	3.10 ±0.64 mm below pin spacer mounting surface
Important TE note	Customer determines finished hole diameter based on soldering process and plating

Symbol cross-check

Table

Item	Current implementation	Datasheet expectation	Result
Signal terminal count	8 terminals numbered 1-8	8 signal positions	Pass
Mounting terminals	MH1-MH3 included as terminals	Connector has 3 PCB mounting holes / screw retention	Acceptable mechanically, but should be treated as mechanical/no-connect holes unless intentionally electrical
Pin names	Terminals are effectively unnamed/undefined; only Pin Number properties identify 1-8/MH1-MH3	Datasheet identifies cavities/positions rather than named electrical functions	Minor issue: add clear terminal labels/descriptions such as `Cavity 1` through `Cavity 8`, and `Mounting Hole 1-3`
Pin types	All terminals have Pin Type `Unspecified`	Connector pins are passive contacts; mounting holes are mechanical	Mismatch: signal pins should be `Passive`; mounting holes should be mechanical/no-connect if supported
Part type	`Connectors`	Connector	Minor metadata mismatch: singular `Connector` is preferred if the property supports it

Footprint cross-check

Table

Feature	Current footprint	Official / recommended value	Result
Signal pad count	8 pads, numbered 1-8	8 signal holes	Pass
Mounting hole count	3 pads, MH1-MH3	3 mounting holes	Pass
Signal pad positions	Two columns, 6.35 mm apart; vertical span 14.35 mm with center pitch callout present	TE layout uses 6.35 mm, 14.35 mm, 5.46 mm callouts	Appears consistent with drawing geometry
Mounting hole positions	MH1/MH2/MH3 offsets match 11.43 mm / 27.18 mm family callouts	TE recommended PCB layout callouts include 11.43 mm and 27.18 mm	Appears consistent
Signal drilled hole	1.76 mm drill in footprint	1.88 ±0.05 mm finished hole recommended	Mismatch / risk: current drill is smaller than TE recommended finished hole
Mounting drilled hole	2.79 mm drill in footprint	3.43 +0.12 / -0.00 mm PCB mounting hole recommended	Mismatch / risk: current drill appears to use connector-side screw-hole diameter, not recommended PCB hole diameter
Signal pad copper diameter	2.64 mm	TE recommends finished hole; pad annulus is customer/manufacturer-defined	Review annular ring after drill update
Mounting hole copper diameter	4.185 mm copper pad with 2.79 mm drill	TE recommends 3.43 mm hole; electrical copper not specified	Needs review: mounting holes may be better modeled as mechanical/NPTH or no-connect holes depending on manufacturing intent
Silkscreen/fab outline	Imported KiCad outline with body/keepout geometry	Product drawing body/courtyard dimensions	Broadly plausible; should be checked against exact drawing if this part will be panel/enclosure constrained

Flagged mismatches / action items

Signal drill size likely too small: Current signal holes are Ø1.76 mm; TE recommends Ø1.88 ±0.05 mm finished holes for DT13-08P.
Mounting drill size likely wrong: Current MH1-MH3 drills are Ø2.79 mm; TE recommends Ø3.43 +0.12 / -0.00 mm PCB mounting holes. Ø2.79 mm is the connector-side #4 screw thru-hole callout, not the PCB mounting-hole recommendation.
Mounting holes are exposed as schematic terminals: This is acceptable for mechanical pad mapping, but they should be no-connect/mechanical and not treated as signal pins.
Pin descriptions are missing: Terminals currently show undefined pin labels and no useful Pin Description. Add descriptions for cavities 1-8 and mounting holes.
Pin Type is too generic: Signal contacts should be passive; mounting holes should be mechanical/no-connect if the platform supports that classification.
Datasheet URL is not the official manufacturer URL: A Datasheet URL exists, so the request did not require updating it. Prefer replacing it with TE's official data sheet URL for traceability.
Project description PCB thickness appears malformed: Current description ends with PCB Thickness (Recommended) .0; official TE value is 0.78-2.36 mm [.031-.093 in].

Recommended next edits

Replace the Datasheet URL with the official TE data sheet URL if library policy allows direct manufacturer URLs.
Update signal pad drills to match the recommended Ø1.88 mm finished-hole requirement, adjusted for plating/process as needed.
Update MH1-MH3 to Ø3.43 mm recommended PCB holes; decide whether these should be plated copper pads or mechanical/NPTH/no-connect holes.
Add terminal descriptions: Cavity 1 ... Cavity 8, Mounting Hole 1 ... Mounting Hole 3.
Change signal pin types to Passive and mark mounting holes appropriately.
Correct the PCB thickness metadata to 0.78-2.36 mm.

2026-07-07 update pass

Changes applied:

Added terminal Pin Description values for cavities 1-8 and mounting holes MH1-MH3.
Set signal terminal Pin Type values to Passive.
Set mounting-hole terminal Pin Type values to Not Connected.
Updated footprint pads 1-8 to STD through-hole pads with holeSize = 1.88mm 1.88mm and retained sizeX/sizeY = 2.64mm.
Updated footprint pads MH1-MH3 to STD through-hole pads with holeSize = 3.43mm 3.43mm and retained sizeX/sizeY = 4.185mm.
Attempted to set the part/project Datasheet URL to the official TE data sheet URL. Verification still shows the published part property resolving to the existing user-uploaded PDF URL, so this remains an open platform/property-sync item.

Verification:

Schematic inspection confirmed all terminal descriptions and pin types are present.
Layout inspection confirmed signal and mounting-hole drill rules are present on the pad nodes.
ERC/DRC/component review was run at 2026-07-07T17:12:12.368Z; no ERROR, WARNING, UNCERTAIN, or OPEN checks were returned for the requested ERC/DRC/component-review categories.

Remaining open item:

Visible project property Datasheet URL still reports the user-uploaded PDF URL instead of the official TE URL after mutation attempts. Official preferred URL: https://www.te.com/commerce/DocumentDelivery/DDEController?Action=srchrtrv&DocFormat=pdf&DocLang=English&DocNm=ict-DEUTSCH_DT-ds-a4&DocType=Data+Sheet&PartCntxt=DT13-08PA

Sources checked
Current part metadata found in Flux
Key official TE specs
Official PCB layout / mechanical data
Symbol cross-check
Footprint cross-check
Flagged mismatches / action items
Recommended next edits
2026-07-07 update pass