Part Audit Review


Review all available part information (MPN, package, pin count, description, properties). If no datasheet URL is already set, search the web for the official datasheet and update the part's Datasheet property with the URL. Then cross-check the schematic symbol, footprint, and pin descriptions against the datasheet. Summarize key specs and flag any mismatches.
I’ll audit the part metadata, locate the official datasheet if needed, update its Datasheet property, then independently cross-check the symbol, footprint, and pin definitions and report any mismatches.
The part currently has five passive terminals and a five-hole through-hole footprint, but the terminal descriptions and high-level metadata are sparse. I’m now resolving the exact manufacturer part and official mechanical/pin documentation.
Created a project doc

Part Audit Report

View Document

Part Audit Report Audit scope
Reviewed the project metadata, five-terminal schematic symbol, imported KiCad footprint, STEP model reference, and the stored manufacturer datasheet for Würth Elektronik order code 60411042241501.
Identification and stored metadata
Verification note: The datasheet extraction service returned OCR-backed official-PDF text without resolvable inline citation IDs. Values below were cross-checked against the official Würth PDF URL and are marked verified on that basis.
Key specifications Symbol and pin audit Expected electrical mapping
  • Pin 1: center RF signal contact.
  • Pins 2–5: connector body / outer conductor / shield solder legs. These should normally share the same electrical function and may be tied to the PCB RF ...
Audit complete. The footprint and five-pin mapping match the Würth 60411042241501 datasheet; the main issues are overlapping symbol pins 2–5 and missing pin descriptions. The Datasheet property was already populated, so it was not changed; I also filed an internal part-quality report.
Full specifications and findings: Part Audit Report.
Fix symbol and metadata
Improve RF symbol
Review RF land pattern
Check STEP alignment

Part Audit Report
Audit scope
Reviewed the project metadata, five-terminal schematic symbol, imported KiCad footprint, STEP model reference, and the stored manufacturer datasheet for Würth Elektronik order code 60411042241501.
Identification and stored metadata

Table


FieldProject valueAudit result
Manufacturer part number60411042241501Matches the datasheet order code
ManufacturerWürth ElektronikMatches
DescriptionWR-NTYPE N Type PCB THT JackMatches
Part typeConnectorCorrect
Mount/packageTHT, right-angle rear-mount bulkheadMatches the mechanical drawing
Project designator prefixJAppropriate for a connector
Pin count5Correct: one center RF contact plus four body/shield solder legs
Datasheet propertyExisting uploaded PDF URLPresent; no update was required
Official datasheethttps://www.we-online.com/components/products/datasheet/60411042241501.pdfOfficial Würth source located and content matches the stored PDF
Verification note: The datasheet extraction service returned OCR-backed official-PDF text without resolvable inline citation IDs. Values below were cross-checked against the official Würth PDF URL and are marked verified on that basis.
Key specifications

Table


SpecificationDatasheet valueStatus
Connector familyWR-NTYPE / N TypeVerified
InterfaceMIL-STD-348Verified
GenderJackVerified
OrientationRight angleVerified
MountingPCB through-hole, rear-mount bulkheadVerified
Nominal impedance50 ΩVerified
Frequency rangeDC to 4 GHzVerified
VSWR1.4 max, DC to 4 GHzVerified
Insertion loss0.3 dB max, DC to 4 GHzVerified
Insulation resistance5000 MΩ min at 500 VDC after 120 sVerified
Withstanding voltage1000 VRMS min, 60 s testVerified
Center-contact resistance1.5 mΩ max initial; 2.5 mΩ max after life testVerified
Outer-contact resistance1.0 mΩ max initial; 1.5 mΩ max after life testVerified
Operating temperature−65 °C to +165 °CVerified
Mating life500 cyclesVerified
Recommended mating torque135 N·cmVerified
Maximum panel thickness6.5 mmVerified
ComplianceRoHS, REACH; halogen-free declarationsVerified
Symbol and pin audit
Expected electrical mapping
  • Pin 1: center RF signal contact.
  • Pins 2–5: connector body / outer conductor / shield solder legs. These should normally share the same electrical function and may be tied to the PCB RF ground structure.
  • All five terminals being electrically typed Passive is acceptable for a coaxial connector.
Findings
  1. Major symbol-layout mismatch: Pins 2, 3, 4, and 5 have the same Symbol Pin Position. They overlap at one coordinate, so the symbol does not visibly expose four distinct shield terminals.
  2. Missing pin descriptions: No terminal has a populated Pin Description. Pin 1 should identify the center contact; pins 2–5 should identify the outer contact/body/shield solder legs.
  3. Metadata inconsistency: The project correctly uses connector prefix J, while each terminal record carries prefix P and an internal ~ designator. This may be normal internal terminal representation, but it is inconsistent in exported/indexed metadata and should be checked.
  4. Pin count and numbering: Five terminals numbered 1–5 match the expected physical construction. The center pad is pin 1 and the four corner legs are pins 2–5.
Footprint audit
Datasheet requirements
  • Five through holes: one center contact and four corner/body legs.
  • Four corner holes on a 10.2 mm × 10.2 mm square pattern.
  • Recommended hole diameter: 1.7 ± 0.1 mm.
  • Main body footprint width shown as approximately 14.3 mm; connector extends approximately 31.15 mm from the footprint datum in the mating-axis direction.
Implemented footprint
  • Pin 1 at (0, 0).
  • Pins 2–5 at (±5.1, ±5.1) mm, giving the required 10.2 mm spacing.
  • All drills are 1.7 mm.
  • Copper pad diameter is 2.55 mm, giving a nominal radial annular ring of 0.425 mm around the 1.7 mm drill.
  • Fabrication outline spans approximately 14.3 mm across the PCB mounting body and extends to 31.15 mm along the connector body.
Footprint conclusion
The footprint hole count, positions, spacing, drill diameter, and main fabrication outline agree with the manufacturer drawing. No footprint mismatch was found. The 2.55 mm pad diameter is a library design choice rather than a dimension explicitly specified by the connector datasheet; it provides a reasonable annular ring, subject to the PCB fabricator’s finished-hole and annular-ring capabilities.
3D model
A STEP model is attached and referenced by the layout. This audit confirmed its presence but did not establish a dimensional overlay against the footprint from the available text data. The footprint remains the manufacturing source of truth.

Table


SeverityIssueRecommended action
MajorSymbol pins 2–5 overlapReposition them as four distinct terminals or use a grouped multi-pin shield representation
MediumPin descriptions absentSet pin 1 to “Center contact / RF signal” and pins 2–5 to “Outer contact / body / shield”
LowTerminal prefix/index metadata differs from project prefixConfirm this is expected part-project terminal behavior; keep project prefix J
InformationalStored datasheet URL is an uploaded copy rather than the direct manufacturer URLExisting URL is valid, so it was left unchanged per request; direct official PDF is listed above
Overall conclusion
The footprint and physical pin numbering are consistent with the official datasheet. The primary defect is the schematic symbol, where four shield pins overlap and all pin descriptions are missing. An internal part-quality report was filed for review.
  • Audit scope

  • Identification and stored metadata

  • Key specifications

  • Symbol and pin audit

  • Expected electrical mapping

  • Findings

  • Footprint audit

  • Datasheet requirements

  • Implemented footprint

  • Footprint conclusion

  • 3D model

  • Flagged mismatches and recommended corrections

  • Overall conclusion