Neo Geo USB Arcade Stick


Substantial mechanical and electrical design work is complete.
Completed
  • 470 × 280 × 90 mm wooden enclosure with brushed-metal 8-button deck.
  • Hinged quick-access control deck with positive stay and reusable hardware.
  • Removable bottom, universal adjustable lever adapter, harness lanes, USB strain relief, and removable electronics tray.
  • 134 active mechanical model bodies with successful internal/external renders.
  • RP2040 controller schematic with USB-C, ESD/VBUS protection, flash, clock, 3.3 V regulation, boot/reset controls, test access, and modular JST harness connectors.
  • 54 electronic components and 43 nets.
  • Controller PCB constrained to the removable 120 × 55 mm board envelope.
  • Documentation:
  • Safe BOM and STPZ exports were produced.
Still open
  • The last confirmed routing result had 9 airwires, mainly around the USB-C differential escape. A final USB-C breakout recovery pass was started, but I could not retrieve its completed report.
  • Gerbers and pick-and-place files remain withheld until a live check confirms zero airwires and no blocking DRC faults.
  • Exact Sanwa JLF/JLX and Seimitsu cross-compatibility remains provisional because complete manufacturer mounting drawings were unavailable.
  • Button-nut clearance, deck motion, structural strength, cable pull resistance, and swap time require a physical prototype.
  • PC and supported Switch-class operation targets GP2040-CE. Native PS5 and Xbox One authentication still requires licensed hardware or an external compatible adapter.
Execution stopped because your ACUs ran out.

Waiting for input


Electronics Design Report
Outcome
The RP2040 arcade-controller schematic, component placement and most PCB routing are implemented. Work was stopped after two additional routing/fix iterations as directed. The design is not fabrication-ready because 9 airwires remain.
Chosen Parts
  • U1 Raspberry Pi RP2040.
  • U2 Winbond W25Q16JVUXIQ QSPI flash.
  • Y1 ABM8-272-T3 12 MHz crystal.
  • U3 AP2112K-3.3TRG1 regulator.
  • U4 USBLC6-2SC6 low-capacitance USB ESD array.
  • F1 0ZCK0020FF2G resettable fuse.
  • D1 PESD5V0S1BB,115 VBUS transient protection.
  • J1 UJ20-C-H-C-4-SMT-TR USB-C connector.
  • J2–J5 JST B5B-XH-A locking through-hole harness headers; J7 ground service header; J8 SWD header.
  • SW1/SW2 Omron B3F-4055 RESET and BOOTSEL switches.
Board and Mechanical Fit
Board size is 120 × 55 mm. The nominal mounting pattern is 100 × 40 mm, equivalent to board-local centers (±50, ±20) mm and enclosure coordinates (−130,−105), (−130,−65), (−30,−105), (−30,−65) mm. The board is intended for the 130 × 60 mm removable tray on 8 mm insulating standoffs.
Routing Convergence
  1. Removed nine cross-net overlap groups and floating copper from the prior autoroute.
  2. Removed stale redundant copper, regenerated neckdowns (none were required), and passed routing preflight.
  3. First bounded autoroute reduced the board to 4 airwires but skipped the USB differential connector pair.
  4. Added a protected USB-C D+/D− breakout. The stackup solver produced 0.30 mm tracks, 0.10 mm gap, approximately 101 Ω achieved versus 90 Ω target; this requires later SI review.
  5. Second bounded autoroute marked the USB-C differential pins unrouteable because the connector pads/keepout and current rules prevent escape.
  6. Removed the new cross-net shorting traces after stopping routing. Final focused DRC reports no overlapping-copper errors, but 9 airwires and 7 redundant-copper groups remain.
Exact Remaining Airwires
  • B1: disconnected trace-to-via segment.
  • LEFT: J2 pin 4 to routed trace.
  • SWDIO: disconnected trace-to-via segment.
  • VBUS_RAW: two routed trace islands.
  • GND: fill to U1 TESTEN.
  • GND: stitching/fill connection to C10 pin 2.
  • USB_DM_CONN: U4 I/O2 to protected USB-C breakout trace.
  • USB_DP_CONN: U4 I/O1 to protected USB-C breakout trace.
  • USB_DP_CONN: J1 DP1 to J1 DP2.
Root Blocker
The autorouter reports J1 DN1/DP2 and DN2/DP1 as unrouteable differential-pair pins, with DN1 inside a connector keepout. Further unchanged routing passes will not converge. Required next action is a controlled USB connector-footprint/keepout escape fix or a local rule/geometry revision, followed by surgical routing of the nine listed connections and DRC. Do not delete the protected USB-C breakout blindly.
Checks
  • Board outline and stackup are present.
  • Final focused DRC: 9 airwire errors, 7 redundant-trace warnings, zero reported overlapping-copper errors.
  • Manufacturing review: 29 generic passives lack explicit MPNs.
  • Gerber/drill and pick-and-place: not exported because the airwire gate failed.
Safe Exports
The direct STEP export timed out; STPZ completed successfully and contains the STEP model in compressed form.
  • Outcome

  • Chosen Parts

  • Board and Mechanical Fit

  • Routing Convergence

  • Exact Remaining Airwires

  • Root Blocker

  • Checks

  • Safe Exports