Credit Refund Request


can you access credit refund request?
I can’t access billing or credit-refund requests. Please contact Flux support through Contact Support; they can view the request and its status.
can you access the file credit refund request?
to read ?
Yes. I can access and read the project document “Credit Refund Request.” I’ve read its full contents. I can also summarize, review, or edit the document, but I cannot access the actual billing/refund ticket or approve credits.
can you add this to the refund request?
Added the attached text to the end of the Credit Refund Request document under “Confirmed non-persistence of the reported completed conversion.”

CX90M Geometry Qualification
Recovery mutation attempts — 2026-09-18 (latest status)
Conversion remains incomplete. No fabrication release or exports. The temporary outline trial was fully restored; no partial notch remains. No external part research or alternative connector selection was repeated.
Concrete operation results
  1. Source terminal compatibility was executed in part task d275c28d. The task reports attempting mutate_designators first with 8-character discriminators and then full UUID-qualified targets. Both reported success but did not persist the names. Independent direct get_schematic after task settlement still returns A1/A12 as duplicate GND and A4/A9 as duplicate VBUS, not GND_1/GND_2/VBUS_1/VBUS_2. Therefore successful atomic compatibility is not established. The existing 22 terminals are still present. Main-board replacement was not retried against this known-incompatible live state.
  2. Exact-arc outline approach: mutate_layout_rules, dry-run, boardShape =svgPath(...) using circular SVG A commands for the unchanged 66 × 27 mm / R1.5 envelope. Rejected with Invalid SVG path for rule 'boardShape': SVG path is self-intersecting: (1.5, 0)→(0, 1000) crosses (31.5, 13.5)→(-31.5, 13.5). This was a valid envelope trial before adding notches, not a newly inferred connector contour.
  3. Supported fallback attempted: mutate_board, DXF string with four LINE and four explicit ARC entities, radius 1.5 mm, millimeter units. Mutation succeeded, but output replaced circular arcs with polygonal L segments, beginning M -0.0315 -0.0135 L 0.0315 -0.0135 L 0.031565 -0.013499 ..., and removed the native cornerRadius rule. This does not retain exact circular geometry under the no-approximation requirement.
  4. Immediately restored with mutate_layout_rules: boardShape=rectangle, cornerRadius=1.5mm, sizeX=66mm, sizeY=27mm. Independent live read-back confirms all four values. No cutout, connector, routing, hole, silk, or net mutation remains on the main board.
The concrete outline limitations are circular-A-command validation failure in the rule path and DXF ARC tessellation into line segments in the fallback. These results do not establish that every possible platform geometry method is unsupported; they satisfy the requested two-approach stop threshold without leaving a partial outline.
Final read-only verification
  • Restored envelope: 66 × 27 mm, native 1.5 mm rounded corners.
  • Routing-state query: 0 airwires, 0 redundant traces in 0 groups.
  • DRC/ERC/placement query: 0 matching ERROR/WARNING/UNCERTAIN/OPEN/UNRUN/RUNNING checks, reviewedAt 2026-09-18T06:23:54.557Z. These are unchanged-board results, not converted-board qualification; no separate exhaustive floating-copper count is claimed.
  • Initial live positions: J605 (−1.6, 10.25 mm), J603 (15.0, 10.25 mm), unchanged by this work. They are component origins, not newly verified mating-face datums.
  • Initial live schematic preserves C604 P1→USB_VBUS, P2→GND; distinct USB_D± and USB_OUT_D±, USB_VBUS and USB_OUT_VCC; separate shield nets through L602/L604. No electrical writes were made here.
  • Stackup inspection reports totalThickness 1.50mm and dielectric 1.499mm; the approved 1.6mm finished thickness is not independently qualified by that internally inconsistent readout. No stackup edit was made.
Scope disposition

Table


ItemStatus
Live baseline and restored-outline inspectionCompleted
Destination terminal rename/publish compatibilityFailed: two reported-success mutation forms did not persist names
J603/J605 replacementUnattempted in this continuation; destination remains incompatible
Exact cutouts with preserved rounded envelopeFailed preflight/fallback; trial outline restored
Mating-face equality and vertical shift verificationUnattempted; no replacement exists
Shell/mount mask and local copper cleanup/routingUnattempted
Post-conversion DRC/ERC, isolation, mechanical validationUnattempted; baseline only verified
Gerber/drills, BOM, CPL, IPC-D-356, STEPUnattempted; fabrication gate not met
No export URLs exist for this conversion. Source-part STEP completion is not established by this continuation and must not be assumed from previous summaries.
Urgent fabrication continuation — current status (supersedes earlier blocker)
The user's approved source hierarchy is accepted: official Hirose ECAD, or verified Ultra Librarian KiCad v6+ export, controls the footprint and cutout geometry. An unlabeled PDF corner radius is not the current stop reason. The +0.14 mm vertical accommodation remains approved.
Exact execution blocker: authenticated ECAD-source retrieval is unavailable through the tools in this session. No authoritative/verified ECAD archive is available among the recovered attachments/assets. The official product HTML has Allegro and Altium anchors with no href or download identifier; its embedded document data contains PDF/IGES/STEP but no footprint download. The two referenced product JavaScript files expose no footprint download handler or endpoint. The verified Ultra Librarian entry requires Login to Download; this session has no authenticated browser/download capability. The code sandbox explicitly reports no network access and can only analyze fetched attachments. No footprint file was obtained, so its cutout geometry has not been inspected or found insufficient. This is an access/tool capability blocker, not a claim that exact geometry is impossible in Flux once the source exists.
Focused retrieval evidence
  • Official Hirose product: raw HTML inspected with code tool; btn-footprint-allegro and btn-footprint-altium each contain an anchor with tabindex="1", class btn-hrsbasenottransform btn-darkgray, and no href.
  • Hirose product-detail JavaScript and product JavaScript: retrieved; no Allegro/Altium/ECAD/footprint handler or public footprint endpoint found.
  • Verified Ultra Librarian entry: identifies footprint CX90M-16P_HIR, Altium and KiCad v6+ exports, but requires login and exposes no concrete download URL or pad/cutout geometry in retrieved content.
  • Required recovery artifact: the downloaded verified KiCad v6+ archive (symbol and footprint), or official Hirose Altium library/archive. Existing drawing/STEP remain supporting authorities. No substitute or estimated contour was authored.
Live baseline inspection — unchanged GCT board only
  • Board: 66 × 27 mm, rectangular outline with 1.5 mm outer corner radius, two copper layers.
  • J605 placement reference: X=−1.6 mm, Y=10.25 mm. J603 placement reference: X=15 mm, Y=10.25 mm. These are component placement coordinates, not qualified external mating-face datums.
  • Live schematic confirms both remain GCT USB4510-03-1-A, part UID 460d71e5-a4f2-4918-ac06-8bea9247dfc0.
  • Live routing-state counts: 0 airwires; 0 redundant traces in 0 groups.
  • DRC/ERC category query returned 0 matching checks for ERROR, WARNING, UNCERTAIN, OPEN, UNRUN, RUNNING; review timestamp 2026-09-17T22:56:31.197Z. This filtered baseline result is not a full post-conversion validation or a separately measured floating-copper/edge-clearance count.
  • No schematic, PCB, holes, placement, routing, mask, silk or electrical mappings were mutated in this continuation. C604 and unrelated circuitry were preserved by non-mutation, not independently requalified.
Assigned scope disposition

Table


ItemStatus
Recover persisted sources and inspect live boardCompleted
Obtain/qualify exact authoritative ECAD partFailed: source access/tool blocker above
Replace J603/J605 and preserve qualified mating-face X/YUnattempted: dependent on exact source
Official local cutouts and shell/mount supportUnattempted: dependent on exact source
Local stale-copper cleanup, routing, mask and silkUnattempted: no replacement performed
Full post-conversion DRC/ERC, geometry/net/polarity verificationUnattempted: conversion absent; baseline checks only
Gerber ZIP and drillsUnattempted: fabrication release gate not reached
BOM, CPL, IPC-D-356, STEP/3DUnattempted: conversion absent
No CX90M fabrication package was generated. Exporting the unchanged GCT board would not satisfy this assignment. No final cutout dimensions or before/after mating-face equality are claimed. Completion of this inspection batch does not complete the conversion.
Outcome of remaining-work continuation
Hardware conversion is blocked before component or PCB mutation. The approved nominal +0.14 mm upward opening shift is accepted and is not a blocker. No general candidate search, repeated live-board inspection, or credit-request update was performed in this continuation.
The specific unresolved manufacturing dimension is the radius of the two rear internal PCB-notch corners, at the junctions between the rear notch wall and its side walls. High-resolution graphical inspection identified curved transitions but no radius callout for these corners. The nearby R0.25 and R0.55 annotations belong to oval shell-slot/land ends, not the board-notch corners. These radii must not be copied onto the notch or estimated from drawing scale.
The supplied STEP models the connector, not the recommended PCB cutout; it cannot independently specify the board routing-tool radius. An explicit Hirose PCB-notch radius or manufacturer-approved cutout CAD geometry is needed to satisfy the user's exact-official-geometry/no-approximation requirement. This is a radius-evidence gap, not a claim that CX90M is incompatible with the approved enclosure accommodation.
Authoritative inputs and evidence attempted
  • Supplied Hirose drawing: CX90M-16P_CL0480-0513-0-00_2DDrawing_D174082_en.pdf, supplied attachment whose identifier ends 3c63df79-f288-4e67-b36a-8d565e4d0368.
  • Supplied connector STEP, already persisted as cx90m-16p-official-ffa2c278-e568-4603-8960-e13557c0d5bb.stp.
  • Focused datasheet retrieval for notch dimensions, shell-slot dimensions, and MID/dummy electrical treatment. The indexed text did not establish these geometric associations or MID continuity; this retrieval failure alone was not treated as proof of missing drawing information.
  • Page-1 rendering at 300 dpi and OCR at +90/-90 degrees recovered vertical dimensions omitted by upright OCR.
  • A further high-resolution inspection followed the PCB-layout dimension witness lines rather than measuring pixels. It isolated the uncalled rear-notch corner radius and recovered the associations below.
Recovered drawing associations — retain for continuation
The following table records graphical extraction from the RECOMMENDED PCB LAYOUT (TOP-VIEW). It is not a final authored footprint or a completed independent geometry verification. Convention: X=0 on connector centerline, Y=0 at the signal/MID land-row center, positive Y toward the mating edge/lower side of the drawing. This convention is not yet transformed into Flux board coordinates.

Table


FeatureRecovered nominal geometry, mmBasis/status
Signal/MID lands18 lands, 0.30 × 0.90Printed dimension callouts; ±0.05 size callouts
Land-row X centers−4.25 to +4.25 in 0.50 increments8.50 span, 4.25 half-span, 0.50 pitch
Shell pairs X centers±5.4010.80 span
Land top and bottom edgesY=−0.45 and +0.45Derived from 0.90 land length
Front/lower slot centersY=+3.85−0.45 + 4.30; 4.30±0.05 witness-line association
Rear/upper slot centersY=+0.753.85 − 3.10; 3.10±0.05 witness-line association
Notch rear wallY=+0.623.85 − boxed/basic 3.23
PCB outer edgeY=+6.473.85 + parenthesized/reference 2.62
Notch width9.35±0.05Printed callout; full contour remains unresolved
Rear/upper slot length2.05±0.05Graphical association
Rear/upper copper-land length2.55±0.05Graphical association
Front/lower slot length1.80±0.05Graphical association
Front/lower copper-land length2.40±0.05Graphical association
Rear internal notch-corner radiusUnresolvedCurved transitions drawn; no applicable radius callout identified
Do not overwrite these results with the previously inspected library geometry: library coordinates and land sizes were not qualified as an exact match. Slot widths, detailed land shapes, plating, mask implementation, full datum transform, and STEP-to-footprint transform still require final reconciliation before authoring.
Electrical qualification remaining
The official front-view pin table establishes A1/A12/B1/B12 as GND; A4/A9/B4/B9 as VBUS; A5 as CC1; B5 as CC2; A6/B6 as D+; A7/B7 as D−; A8 as SBU1; and B8 as SBU2.
This supports the planned preservation of the two connector-specific power/data nets and CC networks, but no replacement pin mapping has been applied. MID plate continuity to MAIN SHELL and the manufacturer's required treatment of dummy contacts remain unverified; the retrieved material identifies MID PLATE and MAIN SHELL separately but does not establish their electrical continuity. Do not guess a GND/shield connection that could bypass either ferrite.
Scope status

Table


Remaining scope itemStatus
Exact drawing/STEP qualificationFailed to complete: rear internal notch radius unresolved; MID/dummy electrical treatment and final transform also unfinished
Exact part creation/correction/importUnattempted: blocked by qualification
Replace J603/J605 and preserve mating-face X/YUnattempted: blocked by qualification; no final placement/mating datum exists
Preserve stackup, three NPTH holes, unrelated geometry/nets/routingCompleted by non-mutation: no hardware edits in this continuation
Apply pin mapping and preserve shield/CC/ESD behaviorUnattempted: connectors unchanged
Local copper cleanup, routing, silk and maskUnattempted: dependent on qualified replacement geometry
Post-conversion geometry read-back and DRC/ERCUnattempted: no conversion exists to validate
Manufacturing gate and exportsUnattempted: no regenerated Gerber/drill, PCBWay BOM, CPL, IPC-D-356, GLB or STEP links
The earlier clean-board counts belong to the unchanged USB4510 implementation and are not evidence that a CX90M conversion is manufacturable. No new conversion check counts are claimed.
  • Recovery mutation attempts — 2026-09-18 (latest status)

  • Concrete operation results

  • Final read-only verification

  • Scope disposition

  • Urgent fabrication continuation — current status (supersedes earlier blocker)

  • Focused retrieval evidence

  • Live baseline inspection — unchanged GCT board only

  • Assigned scope disposition

  • Outcome of remaining-work continuation

  • Authoritative inputs and evidence attempted

  • Recovered drawing associations — retain for continuation

  • Electrical qualification remaining

  • Scope status