Single-project implementation of the Blue Ant AMP Architecture Rev2 using one shared schematic with six logical board partitions: PCB-01 phono stage, PCB-02 input selector and relay attenuator interface, PCB-03 balanced driver and RCA-to-balanced conversion interface, PCB-04 dual logical power amplifier channels, PCB-05 multi-rail power supply, and PCB-06 isolated control and display. Explicit inter-partition connector interfaces and named nets preserve balanced signal handling after RCA conversion, distinct rail domains (+63V, -63V, +15V, -15V, +5V, +3.3V), and documented hard constraints including low-noise analog isolation and high-voltage domain separation.

This project is a low-noise amplifier (LNA) circuit. It primarily uses a BFU520YX transistor as the active component. BNC connectors are used for signal input and output. The circuit is designed for high-frequency signals. #project #Template #projectTemplate #LNA #RF #BFU520YX

This project is a low-noise amplifier (LNA) circuit. It primarily uses a BFU520YX transistor as the active component.

This project is a low-noise amplifier (LNA) circuit. It primarily uses a BFU520YX transistor as the active component. BNC connectors are used for signal input and output. The circuit is designed for high-frequency signals. #project #Template #projectTemplate #LNA #RF #BFU520YX

This project is a low-noise amplifier (LNA) circuit. It primarily uses a BFU520YX transistor as the active component. BNC connectors are used for signal input and output. The circuit is designed for high-frequency signals. #project #Template #projectTemplate #LNA #RF #BFU520YX

Pulse induction metal detector using an Arduino Nano, TC4420-driven IRF3205 coil switch, TL072 analog gain stages, LM393 detection comparator, 12V input power, and buzzer alert, optimized for low-noise sensing and separated analog/power grounds.

Low-noise 1.3V buck regulator for the 1P3_RF rail, 3A output, VBATT input, QFN RPU 10-pin 2.0x2.0mm

Portable potentiostat PCB with low-noise analog front end, dual 3.3 V rails, and 4-layer mixed-signal layout for heavy-metal voltammetry.

Meshtastic ESP32-S3 node with 5 V input, 3.3V low-noise regulation, and I2C expansion.

4-layer marine GPS timing and communication device using nRF52840, u-blox ZED-F9P GNSS with external active antenna via u.FL, 915 MHz LoRa radio, Li-ion battery with USB-C charging, separate clean GNSS LDO and digital 3.3V rail, SPI memory LCD, RGB LEDs, buzzer, and 6-axis IMU. PCB target is a 70 mm circular layout with strict RF zoning, dedicated ground plane, 50 ohm RF traces, physical separation between GNSS and LoRa, and low-noise placement suitable for harsh marine environments.

PIC16F877A-based load-cell measurement system using an HX711 24-bit ADC, 4 MHz crystal clock, load-cell connector, ICSP programming header, regulated 5V input, and low-noise PCB layout for internship deliverables.

Driver drowsiness detection ECG front end based on the AD8232 with ECG electrode interface, analog signal conditioning, a dedicated 50 Hz twin-T notch filter for power-line interference rejection, regulated low-noise analog power, and a downstream conditioned ECG output prepared for processing and fatigue/drowsiness analysis.

Simple bus-powered USB audio interface for MacBook Air and Ableton Live using a USB audio codec, stereo analog input and output path, monitoring buffer stages, USB-C power and data connectivity, and low-noise PCB guidance.

AI Brick Phone — 3.3V Synchronous Buck Upgrade (5V→3.3V ≥1A, Low‑Noise for ESP32 & Audio/ADC)

AI Brick Phone — 3.3V Synchronous Buck Upgrade (5V→3.3V ≥1A, Low‑Noise for ESP32 & Audio/ADC)

Two-PCB low-noise EEG system: Digital board (ESP32-S3-MINI-1U + ADS1299 + CP2102N + USB-C + 1S Li-ion charger/power-path + DF40 mezzanine) and Analog board (3x ADS1299 + REF/BIAS/DRL + driven-shield electrode interfaces + local low-noise regulation + test points). DF40 mezzanine carries only power + digital SPI/control with shared SPI, shared START/RESET, and separate CS/DRDY per AFE. 4-layer stacks with strong analog/digital partitioning and interleaved GND pins on DF40.

Avionics-grade ESP32 data logger: low-noise 3.3V, I2C (MPU9250+BME280), SPI MicroSD, programming pads

Ultra-Stable 850 nm, 1 mW VCSEL Module with Low-Noise Constant-Current Driver and Analog Modulation

Low-Noise High-Gain Discrete MOSFET Audio Amplifier Design

Design a low-noise microphone preamplifier for an electret condenser mic.

The TPSM64404, TPSM64406, and TPSM64406E from Texas Instruments are highly integrated synchronous buck power modules designed for high power density and low EMI performance. These modules feature integrated MOSFETs, inductors, and controllers within a compact 6.5mm × 7.0mm × 2mm overmolded package, making them ideal for space-constrained applications. They support a wide input voltage range of 3V to 36V and deliver adjustable output voltages from 0.8V to 16V. The TPSM64404 offers dual 2A outputs or a stackable 4A output, while the TPSM64406 and TPSM64406E provide dual 3A outputs or a stackable 6A output, with the TPSM64406E rated for extended temperature ranges down to -55℃. These modules achieve peak efficiencies exceeding 93.5% and feature ultra-low quiescent current, making them suitable for battery-powered applications. Designed to meet stringent EMI standards, the modules include features such as dual input paths, integrated capacitors, spread spectrum modulation, and low-noise packaging. Additional functionalities include precision enable inputs, power-good indicators, overcurrent protection, thermal shutdown, and the ability to configure for multiphase operation up to 18A. The TPSM6440xx series is optimized for test and measurement, aerospace, defense, and factory automation applications.

This project is a low-noise amplifier (LNA) circuit. It primarily uses a BFU520YX transistor as the active component. BNC connectors are used for signal input and output. The circuit is designed for high-frequency signals. #project #Template #projectTemplate #LNA #RF #BFU520YX

This project is a low-noise amplifier (LNA) circuit. It primarily uses a BFU520YX transistor as the active component. BNC connectors are used for signal input and output. The circuit is designed for high-frequency signals. #project #Template #projectTemplate #LNA #RF #BFU520YX