The ePaper driver board features a 24-pin FPC connector, built-in charging IC for efficient and safe battery charging, and a JST 2-pin BAT connector for easy battery connection. Ideal for creating WiFi-enabled digital photo frames.

Charger IC Lithium Ion 49-WLP (3.46x3.46) The MAX77962 is a high-performance wide-input 3.2A buck-boost charger with a Smart Power Selector™ and operates as a reverse buck without an additional inductor, allowing the IC to power USB On-the-Go (OTG) accessories. The device integrates low-loss power switches, and provides small solution size, high efficiency, low heat, and fast battery charging. The reverse buck has true-load disconnect and is protected by an adjustable output current limit. The device is highly flexible and programmable through I2C configuration or autonomously through resistor configuration. The battery charger includes a Smart Power Selector to accommodate a wide range of battery sizes and system loads. The Smart Power Selector allows the system to start up gracefully when an input source is available even when the battery is deeply discharged (dead battery) or missing. For battery safety/authentication reasons, the IC can be configured to keep charging disabled, and allow the DC-DC to switch and regulate the SYS voltage. The system processor can later enable charging using the appropriate I2C commands. Alternatively, the IC can be configured to automatically start charging. ● 3.5V to 23V Input Operating Range, 30VDC Withstand Voltage ● 97% Peak Efficiency at 9VIN/7.4VOUT/1.5AOUT ● Reverse Leakage Protection ● 50mA to 3.15A Programmable Input Current Limit ● 50mA to 3.2A Programmable Constant Current Charge ● Remote Differential Voltage Sensing ● 600kHz or 1.2MHz Switching Frequency Options ● System Instant On with Smart Power Selector PowerPath ● Charge Safety Timer ● Die Temperature Regulation with Thermal Foldback Loop ● Input Power Management with Adaptive Input Current Limit (AICL) and Input Voltage Regulation ● 10mΩ BATT to SYS Switch, Up to 10A Overcurrent Threshold ● Reverse Buck Mode 5.1V/1.5A to Support USB OTG ● JEITA Compliant with NTC Thermistor Monitor ● I 2C or Resistor Programmable ● 3.458mm x 3.458mm 49-Bump WLP #CommonPartsLibrary #IntegratedCircuit #PowerManagement #MAX77962

Wireless Power Receiver PMIC 20-VQFN (3.5x4.5) BQ51013BRHLT is a wireless power receiver integrated circuit from Texas Instruments designed for inductive power transfer applications compliant with wireless charging standards. The device integrates power rectification, voltage regulation, communication control, and protection circuitry to enable efficient wireless charging for portable and embedded electronic devices. This receiver IC is optimized for low-power wireless charging systems and supports seamless energy transfer from compatible transmitter platforms without the need for physical connectors. It provides regulated power output suitable for charging batteries and powering embedded systems while incorporating dynamic power management, foreign object detection support, thermal protection, and overvoltage protection for safe operation. The BQ51013BRHLT is widely used in wearable electronics, wireless sensor platforms, medical devices, mobile accessories, handheld products, and compact consumer electronics requiring cable-free charging capability. Its compact package and high integration level simplify PCB layout and reduce external component requirements for space-constrained wireless power designs. #commonpartslibrary #wirelesscharging #powermanagement #texasinstruments #wirelesspower #batterycharging #embeddedhardware #portableelectronics #electronicscomponents #inductivecharging

Charger IC Multi-Chemistry 32-QFN (4x4) The BQ25730RSNR is a highly integrated synchronous buck battery charger and system power management IC developed by Texas Instruments for applications requiring efficient charging of multi-cell lithium-ion and lithium-polymer batteries. The device is optimized for USB Type-C, USB Power Delivery, industrial, and portable embedded systems where high charging efficiency, flexible power management, and compact implementation are required. The charger integrates high-side and low-side MOSFET gate drivers along with advanced power path management features, enabling efficient battery charging while simultaneously powering the system load. The architecture supports NVDC power path operation, allowing stable system voltage regulation even when the battery is deeply discharged or absent. The device supports a wide operating input voltage range and programmable charging parameters suitable for various battery chemistries and capacities. Integrated input current optimization and dynamic power management help maximize available adapter power while preventing overload conditions. The BQ25730RSNR communicates with the host processor through an I²C interface, enabling software configuration, telemetry monitoring, and fault management. Internal ADC functionality provides real-time monitoring of charging voltage, current, temperature, and system operating conditions. Its high integration level reduces external component count and PCB area, making it suitable for compact industrial and portable power applications. Electrical Characteristics Wide input voltage operating range compatible with USB PD adapters and industrial power sources. Supports multi-cell lithium-ion and lithium-polymer battery charging configurations. High-efficiency synchronous buck charging architecture. Programmable charge current and charge voltage through digital control interface. Integrated ADC for system telemetry and power monitoring. Dynamic power management optimizes adapter utilization and system stability. Low standby current operation for battery-powered systems. Charging Features Constant current and constant voltage charging modes. Programmable input current limiting for USB and adapter compliance. Battery preconditioning and charge termination functionality. Support for fast charging operation with thermal regulation. Power path management enables simultaneous battery charging and system operation. Automatic recharge and battery maintenance functionality. Protection Features Input overvoltage protection. Battery overvoltage and overcurrent protection. Thermal regulation and thermal shutdown protection. Short-circuit and fault condition protection. Battery temperature monitoring support using external NTC thermistors. Reverse current protection and adapter isolation. Interface and Control I²C serial communication interface for configuration and monitoring. Programmable charging profiles and operating parameters. Interrupt and status reporting capabilities. Integrated telemetry reporting for voltage, current, and temperature measurements. Autonomous operation capability with minimal host intervention. Package Information Package type is WQFN. Compact thermally enhanced surface-mount package. Optimized for automated PCB assembly and high-density layouts. Applications USB Type-C and USB Power Delivery systems. Industrial portable electronics. Embedded computing platforms. Portable medical and instrumentation equipment. Battery-powered industrial controllers. Handheld terminals and data acquisition systems. Portable consumer and commercial electronics. #commonpartslibrary #integratedcircuit #powermanagement #batterycharger

- Voltage Regulator IC 1 Output 30-FC2QFN (4x4) The MAX77960B/MAX77961B are high-performance wide-input 3A (MAX77960B)/6A (MAX77961B) buckboost chargers with Smart Power Selector™ and operate as a reverse buck converter without an additional inductor, allowing the ICs to power USB on-the-go (OTG) accessories. The devices integrate low-loss power switches and provide high efficiency, low heat, and fast battery charging in a small solution size. The reverse buck has true load disconnect and is protected by an adjustable output current limit. The devices are highly flexible and programmable through I2C configuration or autonomously through resistor configuration. The battery charger includes the Smart Power Selector to accommodate a wide range of battery sizes and system loads. The Smart Power Selector allows the system to start up smoothly when an input source is available even when the battery is deeply discharged (dead battery) or missing. For battery safety/authentication reasons, the ICs can be configured to keep charging disabled, and allow the DC-DC to switch and regulate the SYS voltage. The system processor can later enable charging using I2C commands as appropriate. Alternatively, the ICs can be configured to automatically start charging. #CommonPartsLibrary #IntegratedCircuit #PowerManagement #MAX77961

1.5A USB-Friendly Li-Ion Battery Charger and Power-Path Management IC with 4.2 VBAT The BQ24075TRGTR (from Texas Instruments) is a highly integrated single-cell Li-Ion / Li-Polymer linear battery charger IC with power-path management. It is designed for portable and space-constrained applications, allowing a device to be powered from a USB port or AC adapter while simultaneously charging the battery. The device integrates charging control, power-path management, and safety features into a compact package. A key feature is its Dynamic Power Path Management (DPPM), which ensures the system is powered even when the battery is low or absent, while intelligently managing charging current. Key Features Battery Charging Supports single-cell Li-Ion / Li-Polymer batteries Up to 1.5 A programmable charge current Three-phase charging: Pre-charge (conditioning) Constant current Constant voltage Fixed 4.2 V charge voltage Power Path Management Dynamic Power Path Management (DPPM): Powers system and charges battery simultaneously Prioritizes system load over charging Allows system operation even with: Deeply discharged battery No battery connected Input & Power Features Operates from: USB input (100 mA / 500 mA selectable) AC adapter Programmable input current limit up to 1.5 A Input voltage range: ~4.35 V to 6.4 V (28 V max rating) Input dynamic power management (VIN-DPM) prevents source overload Protection & Safety Thermal regulation and shutdown Over-voltage protection (OVP) Short-circuit and reverse current protection Battery temperature monitoring (NTC thermistor input) Battery disconnect (SYSOFF) feature Control & Status Standalone operation (no MCU required, resistor-programmable) Charge status outputs: Charging Charge complete Power good Physical Characteristics Package: 16-pin VQFN (3 mm × 3 mm) Operating temperature: –40°C to +85°C #commonpartslibrary #integratedcircuit #powermanagement #batterycharger