Ceramic Capacitor 0603 (1608 Metric) Template NO default properties #simplifiedFootprint #noProp #CommonPartsLibrary #SMD

Ceramic Capacitor 0805 (2012 Metric) Template NO default properties #simplifiedFootprint #noProp

Ceramic Capacitor 0402 (1005 Metric) Template NO default properties #simplifiedFootprint #noProp

Ceramic Capacitor 0201 (0603 Metric) Template NO default properties #simplifiedFootprint #noProp

Tantalum Capacitor 2917 (7343 Metric) Template NO default properties #simplifiedFootprint #noProp

Chip Resistor 0603 (1608 Metric) Template NO default properties #simplifiedFootprint #noProp

Chip Resistor 0402 (1005 Metric) Template NO default properties #simplifiedFootprint #noProp

Chip Resistor 0805(2012 Metric) Template NO default properties #simplifiedFootprint #noProp #CommonPartsLibrary #Resistor

Chip Resistor 2010 (5025 Metric) Template NO default properties #simplifiedFootprint #noProp

Tantalum Capacitor 1206 (3216 Metric) Template NO default properties #simplifiedFootprint #noProp #Template

Ceramic Capacitor 0603 (1608 Metric) Template NO default properties #simplifiedFootprint #noProp #CommonPartsLibrary #SMD

NTC Thermistor 0603 (1608 Metric) Template NO default properties #simplifiedFootprint #noProp #commonpartslibrary #ntc #thermistor #sensor #temperature #transducer

Ceramic Capacitor 1210 (3225 Metric) Template NO default properties #simplifiedFootprint #noProp

Inductor SMD 0805 (2012 Metric), IPC_7351 nominal, NO default properties #generic-part-template #simplifiedFootprint #NoProp

This ground symbol behaves identically to the most popular ground symbol https://www.flux.ai/jharwinbarrozo/ground due to the "Part Type" property being set to "Ground." This means changing the designator has no effect on electrical connectivity. If you are trying to use a ground symbol for separate grounds (e.g. analog ground), please use this part https://www.flux.ai/nico/ground-portal or fork the part and change the "Part Type" property to "Portal". The corresponding docs page can be found [here](https://docs.flux.ai/tutorials/working-with-ground--basics--multiple-grounds--and-ground-fill-m)

24 Bit Analog to Digital Converter 3, 5 Input 1 Sigma-Delta 24-PDIP AD7714 DIP-24 The AD7714 is a complete analog front end for low-frequency measurement applications. The device accepts low level signals directly from a transducer and outputs a serial digital word. It employs a sigma-delta conversion technique to realize up to 24 bits of no missing codes performance. The input signal is applied to a proprietary programmable gain front end based around an analog modulator. The modulator output is processed by an onchip digital filter. The first notch of this digital filter can be programmed via the on-chip control register allowing adjustment of the filter cutoff and settling time. The part features three differential analog inputs (which can also be configured as five pseudo-differential analog inputs) as well as a differential reference input. It operates from a single supply (+3␣ V or +5␣ V). The AD7714 thus performs all signal conditioning and conversion for a system consisting of up to five channels Charge Balancing ADC 24 Bits No Missing Codes 0.0015% Nonlinearity Five-Channel Programmable Gain Front End Gains from 1 to 128 Can Be Configured as Three Fully Differential Inputs or Five Pseudo-Differential Inputs Three-Wire Serial Interface SPI™, QSPI™, MICROWIRE™ and DSP Compatible 3 V (AD7714-3) or 5 V (AD7714-5) Operation Low Noise (<150 nV rms) Low Current (350␣ mA typ) with Power-Down (5 mA typ) AD7714Y Grade: +2.7 V to 3.3 V or +4.75 V to +5.25 V Operation 0.0010% Linearity Error –408C to +1058C Temperature Range Schmitt Trigger on SCLK and DIN Low Current (226␣ mA typ) with Power-Down (4 mA typ) Lower Power Dissipation than Standard AD7714 Available in 24-Lead TSSOP Package Low-Pass Filter with Programmable Filter Cutoffs Ability to Read/Write Calibration Coefficients APPLICATIONS Portable Industrial Instruments Portable Weigh Scales Loop-Powered Systems Pressure Transducers #CommonPartsLibrary #IntegratedCircuit #AD7714

WiFi 802.11b/g/n Transceiver Module 2.4GHz ~ 2.5GHz Integrated, Trace Surface Mount The ESP-12F is a compact WiFi module based on the ESP8266EX, widely used in IoT and embedded systems due to its low cost and built-in networking capabilities. Integrated WiFi (2.4 GHz) Supports 802.11 b/g/n Built-in TCP/IP stack (no external WiFi processor needed) Microcontroller + WiFi in one Powered by the ESP8266EX SoC Can run user applications directly (not just a WiFi modem) Flash Memory Typically 4 MB SPI flash (varies by version) GPIO Support Multiple multifunction pins: Digital I/O PWM I2C SPI UART ADC (1 channel) Size: ~16 mm × 24 mm Mounting: Castellated SMD module Antenna: Built-in PCB trace antenna (requires proper keepout zone) Power Requirements Operating Voltage: 3.0V – 3.6V (typical 3.3V) Current Consumption: Idle: ~70 mA Peak (TX): up to ~300 mA Common Interfaces UART – programming and debugging SPI – peripheral communication I2C (software-based) GPIO – general-purpose control #commonpartslibrary #transceiver #module #wireless #rf #wifi

Supervisor Open Drain or Open Collector 1 Channel SOT-23-5 The TPS382x family of supervisors provide circuit initialization and timing supervision, primarily for DSP and processor-based systems. During power on, RESET asserts when the supply voltage VDD becomes greater than 1.1V. Thereafter, the supply voltage supervisor monitors VDD and keeps RESET active low as long as VDD remains less than the threshold voltage, VIT−. An internal timer delays the return of the output to the inactive state (high) to make sure proper system reset. The delay time, td, starts after VDD has risen above the threshold voltage (VIT− + VHYS). When the supply voltage drops below the threshold voltage VIT−, the output becomes active (low) again. No external components are required. All the devices of this family have a fixed-sense threshold voltage, VIT–, set by an internal voltage divider. The TPS382x family also offers watchdog time out options of 200ms (TPS3820) and 1.6s (TPS3823, TPS3824, and TPS3828). • Power-on reset generator with a fixed delay time of 200ms (TPS3823, TPS3824, TPS3825, and TPS3828) or 25ms (TPS3820) • Manual reset input (TPS3820, TPS3823, TPS3825, and TPS3828) • Reset output available in active-low (TPS3820, TPS3823, TPS3824, and TPS3825), active-high (TPS3824 and TPS3825), and open drain (TPS3828) • Supply voltage supervision range: 2.5V, 3V, 3.3V, 5V • Watchdog timer (TPS3820, TPS3823, TPS3824, and TPS3828) • Supply current of 15μA (typical) • 5-pin SOT-23 package • Temperature range: −40°C to 85°C (−40°C to 125°C for TPS3823A-33) #CommonPartsLibrary #IntegratedCircuit #PowerManagement #Supervisor

Three-Terminal Fixed Positive Voltage Regulator The LM7812T is a three-terminal fixed positive linear voltage regulator IC designed to provide a stable +12V DC output from a higher input voltage source. It belongs to the widely used 78xx series regulators, where “12” indicates the fixed output voltage of 12 volts. It is commonly used in power supply circuits, embedded systems, and electronic devices that require a simple, reliable regulated 12V rail without the complexity of external components. The device operates as a linear regulator, meaning it reduces voltage by dissipating excess energy as heat, so proper heatsinking is often required for higher current loads. Key Features of LM7812T Fixed +12V output voltage Output current up to 1A–1.5A (depending on package and cooling) Input voltage range up to ~35V max Built-in thermal shutdown protection Internal current limiting and short-circuit protection Safe-area compensation for reliable operation No external components required for basic operation Good line and load regulation Low quiescent current (~8 mA typical) Available in TO-220 / TO-3 packages (LM7812T variants) Typical Applications DC power supplies (12V regulated rail) Arduino and microcontroller systems Industrial control electronics Sensor and communication circuits Battery-powered systems requiring stable 12V Audio amplifiers and small motor control circuits #CommonPartsLibrary #IntegratedCircuit #PowerManagement