Running LED circuit that utilizes a 555 clock output and a decade counter. It runs when the push-button is held down and then slowly stops once it is released.

Nice — you can do a clean pulse + latch using a single quad Schmitt-NAND chip: 74HC132 (or 74LVC132 for 3.3 V systems). The HC132 contains four 2-input NAND gates with Schmitt inputs so you can both clean a noisy SYN480R DATA line and build an SR latch (NAND SR is active-LOW) inside one package. Only a few passives and a driver transistor are needed. Below is a ready-to-build recipe (parts, wiring, explanation, tuning tips, and an ASCII schematic) — no extra logic ICs required. Parts (per latch) 1 × 74HC132 (quad 2-input NAND with Schmitt inputs). If your system is 3.3 V use 74LVC132 / 74HC132 rated for 3.3 V. Rin = 47 kΩ (input series) Cfilter = 10 nF (input RC to ground) — tweak for debounce/clean time Rpulldown = 100 kΩ (pull-down at input node, optional) Rpullup = 100 kΩ (pull-up for active-LOW R input so reset is idle HIGH) Rbase = 10 kΩ, Q = 2N2222 (NPN) or small N-MOSFET (2N7002) to drive your load Diode for relay flyback (1N4001) if you drive a coil Optional small cap 0.1 µF decoupling at VCC of IC Concept / how it works (short) Use Gate1 (G1) of 74HC132 as a Schmitt inverter by tying its two inputs together and feeding a small RC filter from SYN480R.DATA. This removes HF noise and provides a clean logic transition. Because it's a NAND with tied inputs its function becomes an inverter with Schmitt behavior. Use G2 & G3 as the cross-coupled NAND pair forming an SR latch (active-LOW inputs S̄ and R̄). A low on S̄ sets Q = HIGH. A low on R̄ resets Q = LOW. Wire the cleaned/inverted output of G1 to S̄. A valid received pulse (DATA high) produces a clean LOW on S̄ (because G1 inverts), setting the latch reliably even if the pulse is brief. R̄ is your reset input (pushbutton, HT12D VT, MCU line, etc.) — idle pulled HIGH. Q drives an NPN/MOSFET to switch your load (relay, LED, etc.). Recommended wiring (pin mapping, assume one chip; use datasheet pin numbers) I’ll refer to the 4 gates as G1, G2, G3, G4. Use G4 optionally for additional conditioning or to build a toggler later. SYN480R.DATA --- Rin (47k) ---+--- Node A ---||--- Cfilter (10nF) --- GND | Rpulldown (100k) --- GND (optional, keeps node low) Node A -> both inputs of G1 (tie inputs A and B of Gate1 together) G1 output -> S̄ (S_bar) (input1 of Gate2) Gate2 (G2): inputs = S̄ and Q̄ -> output = Q Gate3 (G3): inputs = R̄ and Q -> output = Q̄ R̄ --- Rpullup (100k) --- VCC (reset is idle HIGH; pull low to reset) (optional) R̄ can be wired to a reset pushbutton to GND or to an MCU pin Q -> Rbase (10k) -> base of 2N2222 (emitter GND; collector to one side of relay coil) Other side of relay coil -> +V (appropriate coil voltage) Diode across coil If you prefer MOSFET low side switching: Q -> gate resistor 100Ω -> gate of 2N7002 2N7002 source -> GND ; drain -> relay coil low side

A momentary or non-latching switch which causes a temporary change in the state of an electrical circuit only while the switch is physically actuated.

A momentary or non-latching switch which causes a temporary change in the state of an electrical circuit only while the switch is physically actuated.

A momentary or non-latching switch which causes a temporary change in the state of an electrical circuit only while the switch is physically actuated.

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #attiny2313 #TPS613222A #ISP #buzzer #reusable #module #simple-embedded #microchip #arduino #sublayout

The analog car design is a self-running electric car that avoids obstacle in the left-right region. The design is mainly supported with 5 circuit components. The 9 V to 5 V converted for voltage-current manipulations. The push-button delay circuit (kill switch) for users to temporarily be able to stop the car motors benefiting from RC circuit, MOSFET transistors, and 74HC14 Hex Schmitt Trigger Inverters. The motor speed controller using potentiometers, inverters, and generic diodes. As well as the HC-SR04 Ultrasonic Sensor circuit to sense the proximity of objects in a field of view.

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #arduino #attiny2313 #TPS613222A #ISP #buzzer #referenceDesign #simple-embedded #microchip #template #reference-design

Low-Power USB-C PD Selectable Output with Push-Button Control and LED Status

Seeed Studio XIAO nRF54L15 Board (Pin Header Removed, JST-PH Battery, Pushbutton Added)

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #attiny2313 #TPS613222A #ISP #buzzer #reusable #module #simple-embedded #microchip #arduino #sublayout

Project Title: Plant Monitoring and Irrigation System Overview: This system is based on the ESP32-S3 and is designed to manage irrigation for a multi-floor building. Key Features: Multi-Floor Operation: The system controls three separate floors. Each floor's irrigation can be managed independently. Irrigation and Pump Control: Each floor uses a solenoid valve to regulate water flow. The solenoid valves are operated via MOSFETs. A relay engages an AC water pump when a MOSFET triggers a solenoid valve. Hardware Interconnects: Screw Terminal connectors are added for connecting the solenoid valves and the motor pump. A DC Jack is included to supply power to the system. User Interface & Connectivity: Two JST connectors are provided for integrating an OLED display, a rotary encoder, and a pushbutton. Future enhancements may include the addition of soil moisture sensors. Remote Control: The system is designed for future integration with Blynk IoT. Blynk IoT will offer both manual control and timer-based irrigation modes for each floor.

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #attiny2313 #TPS613222A #ISP #buzzer #reusable #module #simple-embedded #microchip #arduino #sublayout

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #attiny2313 #TPS613222A #ISP #buzzer #reusable #module #simple-embedded #microchip #arduino #sublayout

This is a schematic of an IR (infrared) remote control system. It's built around a Microchip ATTINY2313 microcontroller (U1) and boasts five push-button switches, an indicator RED LED and an electret buzzer for user interaction. An ISP header provides programming capabilities. The project is battery-powered and implements boost converter TPS613222AD (IC1) for stable power supply. #project #Template #projectTemplate #lock #keypad #arduino #attiny2313 #TPS613222A #ISP #buzzer #referenceDesign #simple-embedded #microchip #template #reference-design

Welcome to your new project. Imagine what you can build here.

A momentary or non-latching switch which causes a temporary change in the state of an electrical circuit only while the switch is physically actuated.