WeMos D1 Mini: LiPo Battery, OLED Display, and Debounced Button System (Final Schematic & Ready for Production)

Nice — you can do a clean pulse + latch using a single quad Schmitt-NAND chip: 74HC132 (or 74LVC132 for 3.3 V systems). The HC132 contains four 2-input NAND gates with Schmitt inputs so you can both clean a noisy SYN480R DATA line and build an SR latch (NAND SR is active-LOW) inside one package. Only a few passives and a driver transistor are needed. Below is a ready-to-build recipe (parts, wiring, explanation, tuning tips, and an ASCII schematic) — no extra logic ICs required. Parts (per latch) 1 × 74HC132 (quad 2-input NAND with Schmitt inputs). If your system is 3.3 V use 74LVC132 / 74HC132 rated for 3.3 V. Rin = 47 kΩ (input series) Cfilter = 10 nF (input RC to ground) — tweak for debounce/clean time Rpulldown = 100 kΩ (pull-down at input node, optional) Rpullup = 100 kΩ (pull-up for active-LOW R input so reset is idle HIGH) Rbase = 10 kΩ, Q = 2N2222 (NPN) or small N-MOSFET (2N7002) to drive your load Diode for relay flyback (1N4001) if you drive a coil Optional small cap 0.1 µF decoupling at VCC of IC Concept / how it works (short) Use Gate1 (G1) of 74HC132 as a Schmitt inverter by tying its two inputs together and feeding a small RC filter from SYN480R.DATA. This removes HF noise and provides a clean logic transition. Because it's a NAND with tied inputs its function becomes an inverter with Schmitt behavior. Use G2 & G3 as the cross-coupled NAND pair forming an SR latch (active-LOW inputs S̄ and R̄). A low on S̄ sets Q = HIGH. A low on R̄ resets Q = LOW. Wire the cleaned/inverted output of G1 to S̄. A valid received pulse (DATA high) produces a clean LOW on S̄ (because G1 inverts), setting the latch reliably even if the pulse is brief. R̄ is your reset input (pushbutton, HT12D VT, MCU line, etc.) — idle pulled HIGH. Q drives an NPN/MOSFET to switch your load (relay, LED, etc.). Recommended wiring (pin mapping, assume one chip; use datasheet pin numbers) I’ll refer to the 4 gates as G1, G2, G3, G4. Use G4 optionally for additional conditioning or to build a toggler later. SYN480R.DATA --- Rin (47k) ---+--- Node A ---||--- Cfilter (10nF) --- GND | Rpulldown (100k) --- GND (optional, keeps node low) Node A -> both inputs of G1 (tie inputs A and B of Gate1 together) G1 output -> S̄ (S_bar) (input1 of Gate2) Gate2 (G2): inputs = S̄ and Q̄ -> output = Q Gate3 (G3): inputs = R̄ and Q -> output = Q̄ R̄ --- Rpullup (100k) --- VCC (reset is idle HIGH; pull low to reset) (optional) R̄ can be wired to a reset pushbutton to GND or to an MCU pin Q -> Rbase (10k) -> base of 2N2222 (emitter GND; collector to one side of relay coil) Other side of relay coil -> +V (appropriate coil voltage) Diode across coil If you prefer MOSFET low side switching: Q -> gate resistor 100Ω -> gate of 2N7002 2N7002 source -> GND ; drain -> relay coil low side

rotary encoder debounce circuit

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Pocket Soundbox – LiPo-Powered Cellular I2S MP3 Audio Player (SIMCom A7670E-LASE, Nano-SIM, I2S MP3 to PCM5101A DAC, FM8002E Amp, 1.8V↔3.3V UART/PWRKEY Level Shifting, Remapped J4, MP2315 3.3V Power Path, USB-C ESD/TVS) with power ON/OFF long-press control via SW2 and Q2 featuring pull-ups, RC debounce, and PFET safety clamp (#Cellular #I2S #LiPo #Audio #powerbutton #debounce #PFET)

Circuito Anti rebote (debounce circuit)

A bidirectional, 3 digit counter for keeping track of points. Includes RC network + Schmitt Trigger for input de-bounce. Made for 9V power supply. Supports Common Cathode displays. 2 layer design

Dual-Board 433 MHz Rolling-Code ATX Power Controller with Integrated 24-Hour Camera Timer and Debounced 2-Pin PANEL_SW Manual Override on U5 Latch Input (Preserves Camera Dial Microswitch Gating)

4-bit Sum/Subtract Unit with Result Memory, Operand Multiplexer, and Debounced Modulo-16 Operation