This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. WIP Items: -Routing In flux, this project demonstrates hierarchal design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose

This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. WIP Items: -Routing In flux, this project demonstrates hierarchal design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose

This is a recreation of the [EV5920-5048-V-00A](https://www.monolithicpower.com/en/ev5920-5048-v-00a.html) from MPS which demonstrates a MP5920 Hot-Swap controller commanding 5 MP5048 e-fuses in parallel. In Flux, this project demonstrates hierarchical design through the use of modules. Additionally, parametric symbols are used extensively to improve schematic cleanliness. Components in the canvas are locked because their positions correspond to the same positions as the original layout. Changelog from Original MPS Design: - Not including GPIO2 or GPIO3 as included in the original board due to NC pin name on the IC. - PC1 and PC2 footprints are 5mm in pitch and 12.5mm in diameter rather than the 16mm diameter in the original layout. This change corresponds with the selected part more accurately. -Renamed Designators to be More Verbose

Connector Header Through Hole 5 position 0.059" (1.50mm) #commonpartslibrary #connector #jst #pinheader #tht

Connector Header Through Hole 5 position 0.059" (1.50mm) #commonpartslibrary #connector #jst #pinheader #tht

Here’s a detailed project description prompt that you can use to generate the circuit: --- ### Project Description for Circuit Generation **Project Title**: Vehicle-to-Vehicle (V2V) Communication System for Preventing Dangerous Overtaking Maneuvers **Objective**: The prime objective of this project is to develop and implement a Vehicle-to-Vehicle (V2V) communication system that enhances road safety by preventing dangerous overtaking maneuvers. This system will provide real-time alerts to drivers about the presence and intentions of nearby vehicles, reducing the risk of collisions and improving overall traffic flow on highways. **Components**: 1. **Microcontroller (e.g., Arduino)** 2. **GPS Module (NEO-6M)** 3. **LoRa Module (SX1272)** 4. **Audio/Visual Alert Systems (e.g., Buzzer, LEDs)** 5. **SD Card Module** 6. **LM7805 Voltage Regulator** 7. **9V Battery** **Connections**: 1. **Power Supply**: - **9V Battery**: - Positive to **LM7805 Voltage Regulator Input** - Negative to **Common Ground** - **LM7805 Voltage Regulator**: - Output to **5V Rail (VCC)** - Ground to **Common Ground** 2. **Microcontroller (e.g., Arduino)**: - **Power**: - VCC to **5V Rail (VCC)** - GND to **Common Ground** 3. **GPS Module (NEO-6M)**: - **Power**: - VCC to **5V Rail (VCC)** - GND to **Common Ground** - **Communication**: - TX to **RX (Digital Pin) of Microcontroller** - RX to **TX (Digital Pin) of Microcontroller** (if needed) 4. **LoRa Module (SX1272)**: - **Power**: - VCC to **3.3V or 5V (based on module specification)** - GND to **Common Ground** - **SPI Communication**: - MOSI to **MOSI (Digital Pin) of Microcontroller** - MISO to **MISO (Digital Pin) of Microcontroller** - SCK to **SCK (Digital Pin) of Microcontroller** - NSS to **CS (Digital Pin) of Microcontroller** 5. **Audio/Visual Alert System (Buzzer, LEDs)**: - **Buzzer**: - Positive to **Digital Output Pin** of Microcontroller through a resistor - Negative to **Common Ground** - **LEDs**: - Anode (Positive) to **Digital Output Pin** of Microcontroller through a resistor - Cathode (Negative) to **Common Ground** 6. **SD Card Module**: - **Power**: - VCC to **3.3V or 5V (based on module specification)** - GND to **Common Ground** - **SPI Communication**: - MOSI to **MOSI (Digital Pin) of Microcontroller** - MISO to **MISO (Digital Pin) of Microcontroller** - SCK to **SCK (Digital Pin) of Microcontroller** - CS to **Digital Pin of Microcontroller** **System Functionality**: - **System Initialization and Configuration**: Ensure the microcontroller and communication modules are correctly initialized and configured for optimal performance. - **GPS Signal Acquisition and Data Parsing**: Accurately acquire and parse GPS data to determine the vehicle's current location and speed. - **Vehicle Position and Speed Calculation**: Calculate precise vehicle position and speed in real-time to provide accurate data for communication. - **V2V Communication Establishment**: Establish a reliable communication link between vehicles using the LoRa module to transmit and receive data. - **Overtaking Intention Detection and Signal Transmission**: Detect overtaking intentions and transmit this information to nearby vehicles to alert them of potential hazards. - **Signal Reception and Processing by Nearby Vehicles**: Ensure nearby vehicles can receive and process overtaking signals to determine the position and speed of the overtaking vehicle. - **Driver Alert Generation**: Generate audio and visual alerts to inform drivers of the presence and intentions of nearby vehicles, especially during overtaking. - **Continuous Monitoring and Data Logging**: Continuously monitor the system's performance and log relevant data for analysis and future improvements.

This project uses an Arduino Mega microcontroller connected to 5 flexible sensors and a mini speaker with position and acceleration sensors to create an interactive device. It uses AMS1117 voltage regulators to provide regulated power, a CH340C for USB communication, and includes capacitors and resistors for circuit balance. Ideal for IoT and edge computing tasks. #referenceDesign #project #ArduinoMega #flexSensors #miniSpeaker #motionSensor #IoT #edgeComputing #reusable #module #Arduino #template