ESP32 8 Relay Board. Has onboard mains to 5V or can use the ESP VIN for the +5V. 8 onboard relays capable of switching about 5A without adding additional tin to the traces.

5V Trigger Relay Module For Arduino And Raspberry Pi 5V Trigger Relay Module For Arduino And Raspberry Pi

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

esp32 module relay on PFC8574 - 5v

ESP32 8 Relay Board. Has onboard mains to 5V or can use the ESP VIN for the +5V. 8 onboard relays capable of switching about 5A without adding additional tin to the traces.

ESP32 8 Relay Board. Has onboard mains to 5V or can use the ESP VIN for the +5V. 8 onboard relays capable of switching about 5A without adding additional tin to the traces.

ESP32 8 Relay Board. Has onboard mains to 5V or can use the ESP VIN for the +5V. 8 onboard relays capable of switching about 5A without adding additional tin to the traces.

ESP32 8 Relay Board. Has onboard mains to 5V or can use the ESP VIN for the +5V. 8 onboard relays capable of switching about 5A without adding additional tin to the traces.

STM32F401 Blackpill-style railway crossing safety controller with dual 12V input selection, LM2596 5V buck, AMS1117-3.3 MCU rail, horn relay driver, and edge-mounted off-board sensor, servo, and UART connectors for modular prototyping.

5V Short Circut Protection based on a relay.

5V Short Circut Protection based on a relay.

Golf ball dispenser controller with protected 12V-24V DC input, LM2596 5V buck, ESP32 control, INA219 relay-coil sensing, and dry-contact relay output.

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

SCADA Sensor Node v2.1 using a Heltec WiFi LoRa 32 V4 module with separate +5V and board-generated +3V3 rails, ADS131M08 8-channel ADC front end, TCA9548A I2C multiplexer, TMP102-based fan control, ULN2003A relay and fan driver, CT/pressure/analog/One-Wire/vibration/humidity/Qwiic/flow/digital sensor interfaces, relay outputs, fan connector, brownout sensing, and a 200 mm x 140 mm 2-layer layout with Heltec keepout, antenna clearance, mounting holes, and DIN-rail slots.

Single-project implementation of the Blue Ant AMP Architecture Rev2 using one shared schematic with six logical board partitions: PCB-01 phono stage, PCB-02 input selector and relay attenuator interface, PCB-03 balanced driver and RCA-to-balanced conversion interface, PCB-04 dual logical power amplifier channels, PCB-05 multi-rail power supply, and PCB-06 isolated control and display. Explicit inter-partition connector interfaces and named nets preserve balanced signal handling after RCA conversion, distinct rail domains (+63V, -63V, +15V, -15V, +5V, +3.3V), and documented hard constraints including low-noise analog isolation and high-voltage domain separation.

This project is a plant monitoring system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #internetOfThings #referenceDesign #edgeComputing #espressif #template #iot #ESP32 #relay

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design

This project involves designing a complete schematic for a robotic arm controller based on the ESP32-C3 microcontroller, specifically using the ESP32-C3-MINI-1-N4 module. The design features a dual power input system and comprehensive power management, motor control, I/O interfaces, and status indicators—all implemented on a 2-layer PCB. Key Specifications: Microcontroller: • ESP32-C3-MINI-1-N4 module operating at 3.3V. • Integrated USB programming connections with reset and boot mode buttons. Power System: • Dual power inputs with automatic source selection: USB-C port (5V input) and barrel jack (6-12V input). • Power management using LM74610 smart diode controllers for power source OR-ing. • AMS1117-3.3 voltage regulator to deliver a stable 3.3V supply to the microcontroller. • Filter capacitors (10μF electrolytic and 100nF ceramic) at the input and output of the regulators. • Protection features including USBLC6-2SC6 for USB ESD protection and TVS diodes for barrel jack overvoltage protection. Motor Control: • Incorporates an Omron G5LE relay with a PC817 optocoupler and BC547 transistor driver. • Provides dedicated header pins for servo motors with PWM outputs. • Flyback diode protection implemented for relay safety. I/O Connections: • Header pins exposing ESP32-C3 GPIOs: Digital I/O (IO0-IO10, IO18, IO19) and serial communication lines (TXD0, RXD0), plus an enable pin. • Each I/O pin includes appropriate 10kΩ pull-up/pull-down resistors to ensure reliable performance. Status Indicators: • A power status LED with a current-limiting resistor. • A user-controllable LED connected to one of the GPIO pins. PCB Layout Requirements: • 2-layer PCB design with separate ground planes for digital and power sections. • Placement of decoupling capacitors close to power pins to reduce noise. • Adequate trace width for power lines to ensure efficient current flow. • Inclusion of mounting holes at the board corners for secure installation. • All components are properly labeled with correct values for resistors, capacitors, and other passive elements, following standard design practices for noise reduction, stability, and reliability. #RoboticArmController #ESP32C3 #SchematicDesign #PCBDesign #ElectronicsDesign #PowerManagement #MotorControl #EmbeddedSystems #IoT

This project is a plant care system that uses an ESP32-S3-MINI-1U-N8 microcontroller to automate plant care tasks. This system includes three Songle relays, multiple resistors, capacitors, and transistors, all powered at 3.3V, 5V, or 12V. It also incorporates a USB Type-C connector. #referenceDesign #edge-computing #edgeComputing #espressif #template #iot #ESP32 #relay #reference-design