Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

12–24 VDC GPS-fix-controlled dual relay board. Relays switch immediately based on valid GPS fix status and provide SPDT contacts for 12/24 V loads up to 3 A with external GPS antenna support.

Ruggedized battery-powered PeakNode 1 LoRa PWAN node with SX1262 LoRa mesh over SPI, LTE Cat-M1/NB-IoT modem, GNSS, LPCNet-capable audio path, USB-C charging and LiFePO4 power management. Targets a 4-layer 90 mm x 60 mm IPC Class 2 layout with 3.3 V main and 1.8 V I/O rails, dual SMA antennas, two RGB status LEDs, three tactile buttons, low-leakage power architecture for sub-10 uA sleep, and defined RF keep-out zones under the LoRa and LTE antenna regions.

High-level recreation of the ThirstIQ Cap wiring diagram using an ESP32-WROOM-32 with AMS1117-3.3 regulated battery input, inline ON/OFF switch, four touch input headers on IO32/IO33/IO25/IO26, shared I2C OLED and RTC on IO21/IO22, UART debug/programming header on TXD0/RXD0, BOOT and RESET pushbuttons on IO0 and EN, buzzer on IO4, common 3V3/GND distribution, and PCB preparation for a 160 mm x 100 mm 4-layer layout. Layout intent includes clean 3.3 V power distribution, local decoupling for regulator and ESP32, accessible external headers/buttons, short clean BOOT/EN traces, shared I2C routing, touch-signal separation from noisy power and buzzer traces, and ESP32 antenna keepout.

Bluetooth RC car controller using ESP32-WROOM-32E, TB6612FNG dual H-bridge, XL4015 5V buck module, DC barrel battery input, dual 2-pin motor screw terminals, 1000uF VM bulk capacitor, 100nF decoupling, 10k EN pull-up, 30 mil power traces, 10 mil signal traces, and ESP32 antenna edge keep-out.

Arctic Tank Monitor — low-power nRF9160 LTE-M sensor node for -40°C tank monitoring. Battery powered from a 3.6 V Li-SOCl2 cell, with TMP117 ambient sensing, external I2C ultrasonic sensor interface, nano-SIM, U.FL LTE antenna, and SWD programming.

Waterproof ESP32-C6 BLE MTB GPS Computer with NEO-M9N, LiPo Power Management, USB-C, and External SMA Antenna

Single-project implementation of the Blue Ant AMP Architecture Rev2 using one shared schematic with six logical board partitions: PCB-01 phono stage, PCB-02 input selector and relay attenuator interface, PCB-03 balanced driver and RCA-to-balanced conversion interface, PCB-04 dual logical power amplifier channels, PCB-05 multi-rail power supply, and PCB-06 isolated control and display. Explicit inter-partition connector interfaces and named nets preserve balanced signal handling after RCA conversion, distinct rail domains (+63V, -63V, +15V, -15V, +5V, +3.3V), and documented hard constraints including low-noise analog isolation and high-voltage domain separation.

This is a compact, high-performance RFID antenna solution built on a printed circuit board configurations. It has miniature RF connector (also known as a U.FL or IPX connector) that allows easy connection to an external antenna. It’s especially useful when you want better signal performance or need to position the antenna away from the main board (e.g., in an enclosure or plastic housing).

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Alarma rompe tímpanos 3000

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

A multi-role sensor platform with some basic sensors onboard with plugs or solder holes for external expansion.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.