This is a reference design of buck based on LT1933 with an internal 0.75A power switch and 3.3V output #3V3 #dcdc #power #referenceDesign #powermanagement #analogdevices #template

A board to use any PWM output with a 3 pin header

A simple voltage divider to showcase how to make parts. A voltage divider is a simple circuit which turns a large voltage into a smaller one. Using just two series resistors and an input voltage, we can create an output voltage that is a fraction of the input. Voltage dividers are one of the most fundamental circuits in electronics.

Design an 8-input to 3-output encoder WITH PRIORITY, considering: 1. truth table. 2. Output equations. 3. Logic diagram. You can use 2, 3 or 4 input logic gates if you prefer. You can do it in a notebook or in a simulator like multisim. If it is in a notebook, make sure that everything looks clean, so I suggest you do it first in draft and then to hand it in.

Tiny USB type-C charger for Li-ion single cell charger based on TP4056 IC. Rprog setting output current to 900mA. VIN and BAT connector are block terminal connectors. #project #typec #charger #TP4056

This project involves designing a DC-DC buck converter circuit to efficiently step down a 12V input voltage to a stable 5V output voltage. The converter is suitable for various electronic applications requiring 5V DC supply from a 12V source.

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

This is a voltage regulator. It steps down an input voltage of up to 40V to a stable output of 3.3V at 3 A.

This project is a low-noise amplifier (LNA) circuit. It primarily uses a BFU520YX transistor as the active component. BNC connectors are used for signal input and output. The circuit is designed for high-frequency signals. #project #Template #projectTemplate #LNA #RF #BFU520YX

A buck boost converter that can be powered from a Li-Ion battery and output 3.3V @ 500mA. Powered by the TPS63051YFFR and in the same package as a standard Adafruit buck converter. Expect to squeeze around 5-10% SoC from a typical Li-Ion battery. Input Voltage Range: 2.5V to 5.5V

multiple output voltage

Build your own Modular LED Sign! This design prioritizes accessibility which means that the BoM can be ordered on Amazon and that everything was designed with solder-ability in mind. NOTE: This board is still an unfinished prototype that has not been built and verified. Operating Instructions: 1. [Important!] Power your buck converter and adjust the output voltage to 1.5V output before attempting to power the LEDs. If you cannot power the buck converter, just turn the potentiometer counterclockwise to its maximum setting.

This project involves designing a DC-DC buck converter circuit to efficiently step down a 12V input voltage to a stable 5V output voltage. The converter is suitable for various electronic applications requiring 5V DC supply from a 12V source.

This is a reference design of step-up dc-to-dc switching converter based ADP1613 with a 15V output #dcdc #power #boost #15V #referenceDesign #powermanagement #analogdevices #template #reference-design

Reference design for Li-ion single cell charger based on TP4056 IC. Rprog setting output current to 900mA. VIN and BAT connector are block terminal connectors. #project #Template #referenceDesign #charger #TP4056 #referenceDesign #batterycharger #template #bms #reference-design #polygon

This is a speech output model for a NIFPES (Nitrogen Injection Fire Prevention and Exhaustion System) machine. ESP32 is being used where it is connected with a limit switch LXW20-11M and ESP32 is connected with DFPlayer mini MP3 Speaker module and the speaker module is further connected to a speaker. This model is powered by a PLC SMPS of 24V and is connected to the door of the control panel of the machine. Function:- Now whenever the door is opened or closed, there is a speech output from the speaker "The door is open" or "The door is closed". Further work to be done:- I need to integrate the fire alarm signals and 20 more signals of 24v each from the PLC output to the ESP32 so that there can be speech outputs whenever any signal is high.

This is a boost converter board based on LM3481 with 5V input and 12V 1.8A output voltage #dcdc #boost #ti #power #referenceDesign #powermanagement #texas-instruments #template #reference-design

Typical Application Circuit for RT6150B-33GQW, 1 Positive Fixed Output 3.3V 800mA. Input voltage 6V max. With JST connectors(Vin and +3V3) and with block terminal connectors(Vin and +3V3) #project-template #voltageregulator #switchingregulator #BuckBoost #project

This project is a WiFi Camera with Motion Detection, utilizing ESP32-CAM module and HC-SR501 PIR sensor. The camera is activated by the sensor's output. The system also includes power regulation and communication headers for setup and control. #WiFi #MCU #PIR #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

This module is a minimalist Arduino Watch design. Consisting of a Microchip ATTINY85-20SU microcontroller, an OLED display for visual output, two user buttons for interface, and a Li-ion Battery for power. The schematic also includes graphic user interface with ISP for programming and minimal passive components for functionality. #wearableDevices #arduino #attiny85

A simple voltage divider to showcase how to make parts. A voltage divider is a simple circuit which turns a large voltage into a smaller one. Using just two series resistors and an input voltage, we can create an output voltage that is a fraction of the input. Voltage dividers are one of the most fundamental circuits in electronics.

This project was intended for the spirit of Halloween, This circuit functions are meant to detect the movement of an object holding candies. If the sensor detect that anyone moves the object, it will send the data from the sensor to the microcontroller. Lastly, once the microcontroller receives the data, it will send it to the buzzer to output a buzz that will stimulate a shock.

Microphone module with volume control and 3.5mm jack return and XLR3 output, in progress