This is the multipurpose PCB that works with Arduino Nano, a way that you can run 2 Stepper motors, 2 DC motors, 2 Servo motors at the same time and this is not it you can even connect BT module, rotary encoder, I2C device, potentiometer at same time. This PCB is very much helpful in building any project and no need to worry about messy wire connections.

This project is a communication device designed with Adafruit's 3857 Microcontroller (U1) and Hoperf's RFM95W-915S2 RF module (U2). The microcontroller interfaces with the RF module via SPI protocol for wireless data transmission. The project also includes a capacitor (C1) and an SMA connector (J1). #LoRa #IoT #project #M4 #Adafruit

Glucose meter is a medical device that determines the approximate concentration of glucose in the blood. A strip containing chemicals that react with glucose in the drop of blood is used for each measurement. Op Amp Circuit description: LMC6484 IC_D is an integrator circuit. LMC6484 IC_A and IC_C are configured as unity gain buffer amplifiers. LMC6484 IC1B is configured as a trans impedance amplifier. Arduino is used for processing of the measured glucose level. The Arduino use the built in ADC module for analog to digital conversion. Further, the Arduino helps to detect the strip also.

Bluetooth, WiFi 802.11b/g/n, Bluetooth 4.2 Transceiver Module 2.412GHz ~ 2.484GHz Antenna Not Included, I-PEX Surface Mount #Module #RF #Transceiver #bluetooth #Wifi

To optimize your 4-layer board manufacturing process with Seeed Studio Fusion, utilize this comprehensive template. It incorporates a majority of the essential manufacturing constraints as global rules, ensuring a smoother and more efficient production workflow. #project-template #template #manufacturer-design-rules This project is a vessel monitoring system built using Seeed Studio Xiao Sense, Xiao Expansion Board with OLED, a UART WiFi module, a normally open float switch, and a UART SIM800L cellular module. The system displays a 30-second countdown on the OLED screen, calibrates the IMU sensor, converts to Euler angles, and stores these values for comparison with future readings. It also sets up the WiFi module as an access point to configure the vessel's name, contact numbers, and angle thresholds for list and trim notifications. Reports are sent at specified times via the cellular module.

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

This project is a WiFi Camera with Motion Detection, utilizing ESP32-CAM module and HC-SR501 PIR sensor. The camera is activated by the sensor's output. The system also includes power regulation and communication headers for setup and control. #WiFi #MCU #PIR #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

Dual Motor Driver Circuit using L298N motor driver module with Atmega8a..

This is a reference design of boost module based on LT8410, with output voltage 16V and input 2.5-16V #dcdc #boost #power #16V #referenceDesign #powermanagement #analogdevices #template #reference-design

4 Relay Module Made BY Randika

Dual Motor Driver Circuit using L298N motor driver module with Atmega8a..

This is a reference design of the ESP8684-WROOM-02C WiFi module from Espressif Systems. This board has USB C for flashing via CH340, RESET and BOOT buttons, 3.3V regulator and 2 IO connectors #WiFi #BLE #MCU #referenceDesign #simple-embedded #espressif #template #reference-design

ATMEGA328-PU (U1) Setup Power Supply Connections: Connect U1:VCC to U2:5V@1 (5V power supply). Connect U1:GND to U2:GND@1 (Ground). Connect U1:AVCC to U2:5V@2 (Analog Power Supply for better ADC performance). Multiple GND pins (U2:GND@1, U2:GND@2, U2:GND@3, U2:GND@4) should all be connected to a common ground plane for stability. Serial Communication for Debugging: Connect U1:PD0 (RX) to U6:TXD. Connect U1:PD1 (TX) to U6:RXD. These connections enable serial communication between the microcontroller (ATmega328) and the USB-Serial adapter (CH340N) for programming and debugging. Sensor Data Acquisition: Given the components, the MLX90614ESF-ACC-000-SP (U4) is an infrared temperature sensor that could be used for vital detection. It uses an I 2 2 C interface. Connect U1:PC4 (SDA) to U4:PWM_SDA. Connect U1:PC5 (SCL) to U4:SCL_Vz. This allows the ATmega328 to communicate with the MLX90614ESF infrared temperature sensor. Additional Considerations: An analog-to-digital converter (ADC) or a specialized RF module designed for UWB radar applications would be necessary to capture and process radar signals for detecting human vitals through walls. The MAX270CWP+ (U3) could be used for audio signal processing but may not directly apply to UWB radar signal processing. Power Supply to Other Components Connect U6:VCC to U2:5V@1. Connect U4:VDD to U2:5V@2. Ensure all components' ground pins are connected to the common ground plane (U2:GND@1, GND@2, GND@3, GND@4)

Dual Motor Driver Circuit using L298N motor driver module with Atmega8a..

This is example board for creating cool projects with stm32 (this board based on STM32F031F6P6) #stm32 #arm #f0 #module

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

A scalable 4x camera array for 3D photogrammetry reconstruction which uses I2C to connect between each module.

GPS01-TD module is a quad-mode Mini GPS module that supports BDS/GPS/GLONASS/Galileo/QZSS/SBAS and fully supports BeiDou B3, which can provide users with high quality, strong anti-jamming and low-power positioning and navigation solutions.

16V 20A Scalable DC/DC Power Module with PMBus #ultralibrarian

Dual Motor Driver Circuit using L298N motor driver module with Atmega8a..

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

This project is a WiFi Camera with Motion Detection, utilizing ESP32-CAM module and HC-SR501 PIR sensor. The camera is activated by the sensor's output. The system also includes power regulation and communication headers for setup and control. #WiFi #MCU #PIR #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

A rack-mount power distribution module with power monitoring and surge protection

Dual Motor Driver Circuit using L298N motor driver module with Atmega8a..