Elementos necesarios en Proteus 8 Busca estos componentes en la biblioteca (modo "Pick Devices"): Conector J1772 – usa un conector genérico de 4 pines (como HEADER 4 o un DB9 si necesitas algo similar). Resistencias: R1: 150 Ω R2: 330 Ω R3: 150 Ω R4: 2.7 Ω Interruptor SPST o jumper simulando "Punto A", "Punto B" y "GND". Fuente de alimentación de 5V para simular BAT1. Ground (GND) para las conexiones a tierra. Batería (Battery) de 5V (puede ser una batería o una carga equivalente en Proteus). Indicador LED (opcional) si quieres ver visualmente la salida de carga o conexión. 🛠️ Pasos para construir el circuito Sección del conector (lado izquierdo) Coloca un conector de 4 pines y nómbralo "J1772". Conecta el primer pin a una fuente de 5V opcional (simulando señal de control). Añade las resistencias R1 (150Ω) y R2 (330Ω) en serie, con un nodo medio hacia “Punto A”. Conecta el otro lado de R1 a "Punto B". Conecta el otro extremo de R2 a tierra. Agrega interruptores SPST para "Punto A", "Punto B" y "GND" para simular las uniones cuando se conectan al cargador. Sección de carga (lado derecho) Coloca las resistencias R3 (150Ω) y R4 (2.7Ω) tal como en la imagen, entre el conector y la batería. Coloca una batería (BAT1) de 5V, y conecta el negativo a tierra. Asegúrate de cerrar correctamente los interruptores (simulando conexión). 🔄 Simulación Usa "Interactive Simulation" en Proteus. Agrega etiquetas como "PUNTO A", "PUNTO B", etc., si deseas facilitar el seguimiento. Observa cómo el voltaje pasa a través de las resistencias y carga la batería. Puedes usar voltímetros o osciloscopios virtuales para observar los cambios de voltaje y corriente. ✅ Consejos finales Si no encuentras la resistencia exacta de 2.7Ω, puedes colocar una personalizada. Puedes usar Virtual Terminal si quieres simular señales de comunicación en el conector. El conmutador central (como se muestra en la línea de puntos) puede implementarse con switches DPDT o nodos que conectes manualmente en la simulación.

This project involves designing a complete schematic for a robotic arm controller based on the ESP32-C3 microcontroller, specifically using the ESP32-C3-MINI-1-N4 module. The design features a dual power input system and comprehensive power management, motor control, I/O interfaces, and status indicators—all implemented on a 2-layer PCB. Key Specifications: Microcontroller: • ESP32-C3-MINI-1-N4 module operating at 3.3V. • Integrated USB programming connections with reset and boot mode buttons. Power System: • Dual power inputs with automatic source selection: USB-C port (5V input) and barrel jack (6-12V input). • Power management using LM74610 smart diode controllers for power source OR-ing. • AMS1117-3.3 voltage regulator to deliver a stable 3.3V supply to the microcontroller. • Filter capacitors (10μF electrolytic and 100nF ceramic) at the input and output of the regulators. • Protection features including USBLC6-2SC6 for USB ESD protection and TVS diodes for barrel jack overvoltage protection. Motor Control: • Incorporates an Omron G5LE relay with a PC817 optocoupler and BC547 transistor driver. • Provides dedicated header pins for servo motors with PWM outputs. • Flyback diode protection implemented for relay safety. I/O Connections: • Header pins exposing ESP32-C3 GPIOs: Digital I/O (IO0-IO10, IO18, IO19) and serial communication lines (TXD0, RXD0), plus an enable pin. • Each I/O pin includes appropriate 10kΩ pull-up/pull-down resistors to ensure reliable performance. Status Indicators: • A power status LED with a current-limiting resistor. • A user-controllable LED connected to one of the GPIO pins. PCB Layout Requirements: • 2-layer PCB design with separate ground planes for digital and power sections. • Placement of decoupling capacitors close to power pins to reduce noise. • Adequate trace width for power lines to ensure efficient current flow. • Inclusion of mounting holes at the board corners for secure installation. • All components are properly labeled with correct values for resistors, capacitors, and other passive elements, following standard design practices for noise reduction, stability, and reliability. #RoboticArmController #ESP32C3 #SchematicDesign #PCBDesign #ElectronicsDesign #PowerManagement #MotorControl #EmbeddedSystems #IoT

A board to test different resistors in an RC circuit. Singal input, goes into resistors, manually select which resistor goes out to one pin of the external capacitor, and a path to capacitor ground. An general purpose button with exposed pins is included

A common return path for electric current. Commonly known as ground.

ATMEGA328-PU (U1) Setup Power Supply Connections: Connect U1:VCC to U2:5V@1 (5V power supply). Connect U1:GND to U2:GND@1 (Ground). Connect U1:AVCC to U2:5V@2 (Analog Power Supply for better ADC performance). Multiple GND pins (U2:GND@1, U2:GND@2, U2:GND@3, U2:GND@4) should all be connected to a common ground plane for stability. Serial Communication for Debugging: Connect U1:PD0 (RX) to U6:TXD. Connect U1:PD1 (TX) to U6:RXD. These connections enable serial communication between the microcontroller (ATmega328) and the USB-Serial adapter (CH340N) for programming and debugging. Sensor Data Acquisition: Given the components, the MLX90614ESF-ACC-000-SP (U4) is an infrared temperature sensor that could be used for vital detection. It uses an I 2 2 C interface. Connect U1:PC4 (SDA) to U4:PWM_SDA. Connect U1:PC5 (SCL) to U4:SCL_Vz. This allows the ATmega328 to communicate with the MLX90614ESF infrared temperature sensor. Additional Considerations: An analog-to-digital converter (ADC) or a specialized RF module designed for UWB radar applications would be necessary to capture and process radar signals for detecting human vitals through walls. The MAX270CWP+ (U3) could be used for audio signal processing but may not directly apply to UWB radar signal processing. Power Supply to Other Components Connect U6:VCC to U2:5V@1. Connect U4:VDD to U2:5V@2. Ensure all components' ground pins are connected to the common ground plane (U2:GND@1, GND@2, GND@3, GND@4)

This is a stereo WiFi camera reference design using dual ESP32-CAM modules for edge computing. The design includes connections for power, ground, and core communication features; UART for control & data transfer, and BOOT pins for mode selection. #WiFi #MCU #stereo #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

Here’s a detailed project description prompt that you can use to generate the circuit: --- ### Project Description for Circuit Generation **Project Title**: Vehicle-to-Vehicle (V2V) Communication System for Preventing Dangerous Overtaking Maneuvers **Objective**: The prime objective of this project is to develop and implement a Vehicle-to-Vehicle (V2V) communication system that enhances road safety by preventing dangerous overtaking maneuvers. This system will provide real-time alerts to drivers about the presence and intentions of nearby vehicles, reducing the risk of collisions and improving overall traffic flow on highways. **Components**: 1. **Microcontroller (e.g., Arduino)** 2. **GPS Module (NEO-6M)** 3. **LoRa Module (SX1272)** 4. **Audio/Visual Alert Systems (e.g., Buzzer, LEDs)** 5. **SD Card Module** 6. **LM7805 Voltage Regulator** 7. **9V Battery** **Connections**: 1. **Power Supply**: - **9V Battery**: - Positive to **LM7805 Voltage Regulator Input** - Negative to **Common Ground** - **LM7805 Voltage Regulator**: - Output to **5V Rail (VCC)** - Ground to **Common Ground** 2. **Microcontroller (e.g., Arduino)**: - **Power**: - VCC to **5V Rail (VCC)** - GND to **Common Ground** 3. **GPS Module (NEO-6M)**: - **Power**: - VCC to **5V Rail (VCC)** - GND to **Common Ground** - **Communication**: - TX to **RX (Digital Pin) of Microcontroller** - RX to **TX (Digital Pin) of Microcontroller** (if needed) 4. **LoRa Module (SX1272)**: - **Power**: - VCC to **3.3V or 5V (based on module specification)** - GND to **Common Ground** - **SPI Communication**: - MOSI to **MOSI (Digital Pin) of Microcontroller** - MISO to **MISO (Digital Pin) of Microcontroller** - SCK to **SCK (Digital Pin) of Microcontroller** - NSS to **CS (Digital Pin) of Microcontroller** 5. **Audio/Visual Alert System (Buzzer, LEDs)**: - **Buzzer**: - Positive to **Digital Output Pin** of Microcontroller through a resistor - Negative to **Common Ground** - **LEDs**: - Anode (Positive) to **Digital Output Pin** of Microcontroller through a resistor - Cathode (Negative) to **Common Ground** 6. **SD Card Module**: - **Power**: - VCC to **3.3V or 5V (based on module specification)** - GND to **Common Ground** - **SPI Communication**: - MOSI to **MOSI (Digital Pin) of Microcontroller** - MISO to **MISO (Digital Pin) of Microcontroller** - SCK to **SCK (Digital Pin) of Microcontroller** - CS to **Digital Pin of Microcontroller** **System Functionality**: - **System Initialization and Configuration**: Ensure the microcontroller and communication modules are correctly initialized and configured for optimal performance. - **GPS Signal Acquisition and Data Parsing**: Accurately acquire and parse GPS data to determine the vehicle's current location and speed. - **Vehicle Position and Speed Calculation**: Calculate precise vehicle position and speed in real-time to provide accurate data for communication. - **V2V Communication Establishment**: Establish a reliable communication link between vehicles using the LoRa module to transmit and receive data. - **Overtaking Intention Detection and Signal Transmission**: Detect overtaking intentions and transmit this information to nearby vehicles to alert them of potential hazards. - **Signal Reception and Processing by Nearby Vehicles**: Ensure nearby vehicles can receive and process overtaking signals to determine the position and speed of the overtaking vehicle. - **Driver Alert Generation**: Generate audio and visual alerts to inform drivers of the presence and intentions of nearby vehicles, especially during overtaking. - **Continuous Monitoring and Data Logging**: Continuously monitor the system's performance and log relevant data for analysis and future improvements.

Motor Driver Contains The following blocks: - Tachometer - Speed Compensator (with Virtual Ground) - Directions control - Arduino source - ESP 32 Cam

Rocket's igniter ground station control unit

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

- ESP32 DevKitC V4 (microcontroller) - 2x BME280 sensors (temperature, humidity, pressure) - 8ch relay board with 12VDC relays (NO/NC SPDT) - 12VDC power supply - USB connectivity - Various components (resistors, caps, opto couplers, op-amps, motor drivers, multiplexers) - 2x SPDT relay boards (for fan fail-safe) - 4x 2ch bidirectional level controllers (3.3V to 5V) - ESP32 GPIO 21 (SCL) to BME280's SCL - ESP32 GPIO 22 (SDA) to BME280's SDA - ESP32 GPIO 5 (digital output) to 8ch relay board input - ESP32 GPIO 25 (PWM output) -> Fan PWM (0-255 value) - ESP32 GPIO 26 (PWM output) -> Light PWM (0-255 value) - ESP32 GPIO 34 (analog input) -> Tachometer input (0-4095 value, 12-bit ADC) - Add a 5V voltage regulator (e.g., 78L05) to power the ESP32 and other 5V components - Add a 3.3V voltage regulator (e.g., 78L03) to power the BME280 sensors and other 3.3V components - Include decoupling capacitors (e.g., 10uF and 100nF) to filter the power supply lines - Ensure proper grounding and shielding to minimize noise and interference -- Power supply: - VCC=12VD Available, to be used for LM358P - 5V voltage regulator (78L05) - VCC=5V, GND=0V - 3.3V voltage regulator (78L03) - VCC=3.3V, GND=0V - 3.3V voltage regulator (78L03) - VCC=3.3V, GND=0V - Fan PWM boost: - Input (3.3V PWM): 0-3.3V, frequency=20kHz - Output (5V PWM): 0-5V, frequency=20kHz - LM358P op-amp (unity gain buffer) - VCC=5V, GND=0V - R1=1kΩ, R2=1kΩ, R3=1kΩ, R4=1kΩ - C1=10uF (50V), D1=1N4007 - 0-10V signal conditioning: - Input (3.3V PWM): 0-3.3V, frequency=13kHz - Output (0-10V): 0-10V, frequency=13kHz - LM358P op-amp (non-inverting amplifier) - VCC=5V, GND=0V - R5=2kΩ, R6=1kΩ, R7=2kΩ, R8=1kΩ, R9=1kΩ, R10=2kΩ - C2=10uF (50V), R11=10kΩ (1%) ------------------------------------ Fan PWM Boost (3.3V to 5V): 1. ESP32 GPIO 25 (PWM output) -> R1 (1kΩ) -> VCC (3.3V) 2. ESP32 GPIO 25 (PWM output) -> R2 (1kΩ) -> Vin (LM358P) 3. LM358P (Voltage Follower): - VCC (5