This project is a Battery Management System (BMS) built around STMicroelectronics' STC3115AIQT battery monitor IC. It uses I2C for communication, features alarm management, and supports battery charging. The power supply, battery connection points, and debug interface are facilitated through connectors. #project #Template #charger #monitor #reusable #module #batterycharger #template #bms #STC3115 #stm

The MAX485 TTL to RS-485 Interface Module allows MCUs to use the RS-485 differential signaling for robust long distance serial communications.

ATMEGA328-PU (U1) Setup Power Supply Connections: Connect U1:VCC to U2:5V@1 (5V power supply). Connect U1:GND to U2:GND@1 (Ground). Connect U1:AVCC to U2:5V@2 (Analog Power Supply for better ADC performance). Multiple GND pins (U2:GND@1, U2:GND@2, U2:GND@3, U2:GND@4) should all be connected to a common ground plane for stability. Serial Communication for Debugging: Connect U1:PD0 (RX) to U6:TXD. Connect U1:PD1 (TX) to U6:RXD. These connections enable serial communication between the microcontroller (ATmega328) and the USB-Serial adapter (CH340N) for programming and debugging. Sensor Data Acquisition: Given the components, the MLX90614ESF-ACC-000-SP (U4) is an infrared temperature sensor that could be used for vital detection. It uses an I 2 2 C interface. Connect U1:PC4 (SDA) to U4:PWM_SDA. Connect U1:PC5 (SCL) to U4:SCL_Vz. This allows the ATmega328 to communicate with the MLX90614ESF infrared temperature sensor. Additional Considerations: An analog-to-digital converter (ADC) or a specialized RF module designed for UWB radar applications would be necessary to capture and process radar signals for detecting human vitals through walls. The MAX270CWP+ (U3) could be used for audio signal processing but may not directly apply to UWB radar signal processing. Power Supply to Other Components Connect U6:VCC to U2:5V@1. Connect U4:VDD to U2:5V@2. Ensure all components' ground pins are connected to the common ground plane (U2:GND@1, GND@2, GND@3, GND@4)

A circuit for a gps tracker using stm32f103c8t6 and sim 808, that acquires and sends gps coordinates to a separate interfaced application. The circuit will be powered by a 12v dc battery so there a need for power regulation. there is a USB type micro B for code uploading.

This is a reference design of LTC2875IS8#TRPBF with a standard configuration for normal mode #LTC2875IS8#TRPBF #can #interface #transceiverCircuit #referenceDesign #canbus #analogdevices #template #reference-design

This is a reference design for TJA1059TKJ Dual high-speed CAN transceiver with Standby mode. It offers advanced features, such as wake-up capability and high-speed data rates, making it suitable for automotive and industrial applications. #MCP25612FD #CANbus #transceiver #highspeed #automotive #referenceDesign #project #CANbus #interface #transceiverCircuit #TJA1059TKJ #referenceDesign #canbus #nxp #template #reference-design

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #reusable #module #edgeComputing #espressif #template

This is a reference design of MAX33041EASA+ with a standard configuration for normal mode #MAX33041EASA+ #can #interface #template #transceiverCircuit #referenceDesign #canbus #analogdevices #reference-design

This project is a Battery Management System (BMS) built around STMicroelectronics' STC3115AIQT battery monitor IC. It uses I2C for communication, features alarm management, and supports battery charging. The power supply, battery connection points, and debug interface are facilitated through connectors. #project #Template #charger #monitor #reusable #module #batterycharger #template #bms #STC3115 #stm

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #reusable #module #edgeComputing #espressif #template

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

This is a 16x2 LCD display screen with I2C interface. It is able to display 16x2 characters on 2 lines, white characters on blue background.

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #referenceDesign #edgeComputing #espressif #template #reference-design

10/100 Base-T/TX PHY Ethernet controller that supports PoE with SPI Interface. Based on W5500. Can be used as PoE injector. #project #referenceDesign #template #w5500 #PoE #EtherNet #RJ5

This project is a motherboard for the ESP32-CAM module, which enables easy and flexible WiFi camera applications. The motherboard provides power supply, programming interface, and GPIO expansion for the ESP32-CAM. It also supports external sensors for more functionality. #motherboard #WiFi #MCU #ReferenceDesign #project #ESP32 #camera #reusable #module #edgeComputing #espressif #template

ATTiny10 Based Snowflake PCB Programmed using Arduino over Tiny Programming Interface Roughly 88x80 mm size

The TCA9555 is a 16-bit I/O expander for the I2C bus, designed for voltage operation from 1.65 V to 5.5 V. It provides general-purpose remote I/O expansion for most microcontroller families through the I2C interface. This device features low standby- current consumption, 5-V tolerant I/O ports, and an open-drain active-low interrupt output. It is commonly used for controlling LEDs, controlling enable or reset signals of other devices, and reading the outputs of other devices or buttons.

This project is a design for a UV sensor circuit based on the Lite-On LTR-390UV-01. Key components include a voltage regulator (AP2112K-3.3TRG1), level-shifting N-channel MOSFETs (BSS138), resistors, and capacitors. The circuit interface includes I2C communication and power connections, facilitated through JST connectors. #referenceDesign #industrialsensing #liteon #template #reference-design

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

Reference design for PCM5102A 2VRMS DirectPath™, 112dB Audio Stereo DAC with 32-bit, 384kHz PCM Interface #project-template #DAC #audio #project

This TJA1051TK-based reference design is a CAN bus transceiver circuit, providing reliable data communication over the CAN network. The design features a range of capacitors and resistors to ensure signal integrity, and a NUP2105L for voltage protection. It's ideal for applications requiring reliable data communication in an automotive or industrial environment. #referenceDesign #project #CANbus #interface #transceiverCircuit #TJA1051TK/3,118 #TJA1051TK #referenceDesign #canbus #nxp #template #reference-design

This is a LoRa remote control project built around a Raspberry Pi RP2040 SoC and the RFM95W LoRa module. The design includes user interface features such as multiple buttons and LEDs, power management components, and a temperature sensor. The project utilizes SPI, I2C, and USB interfaces for communication and control. #referenceDesign #simple-embedded #raspberrypi #lora #template #reference-design

This is a reference design for TJA1059TKJ Dual high-speed CAN transceiver with Standby mode. It offers advanced features, such as wake-up capability and high-speed data rates, making it suitable for automotive and industrial applications. #MCP25612FD #CANbus #transceiver #highspeed #automotive #referenceDesign #project #CANbus #interface #transceiverCircuit #TJA1059TKJ #referenceDesign #canbus #nxp #template #reference-design

This Weather Station Logger project employs the versatile ESP32 microcontroller board, integrated with an SD card slot for data storage. It features a USB interface for easy programming and is efficiently powered by a single 18650 battery, complete with a protection circuit for safe operation. #iot #esp32 #lora #weather #edgecomputing

The TCA9555 by Texas Instruments is a low-voltage, 16-bit I2C and SMBus I/O expander designed to provide general-purpose remote I/O expansion for most microcontroller families via the I2C interface. Operating at a voltage range of 1.65V to 5.5V, this component integrates two 8-bit Configuration, Input Port, Output Port, and Polarity Inversion registers, making it an ideal solution for applications requiring additional I/Os such as servers, personal computers, routers, industrial automation equipment, and products with GPIO-limited processors. The TCA9555 features a low standby-current consumption of 3.5uA maximum, compatibility with 5V I/O ports, a 400kHz Fast I2C Bus, and includes an open-drain active-low interrupt output which enhances its utility in complex systems. Noteworthy for its high-current drive capability suitable for directly driving LEDs, the TCA9555 also brings a configurable slave address with 3 address pins, providing the flexibility needed in varied application requirements. Offering robust protection with latch-up performance exceeding 100mA per JESD 78, Class II, and ESD protection exceeding JESD 22, the TCA9555 combines reliability with expansive functionality for sophisticated electronic designs.