Industrial ESP32-S3 master gateway with Ethernet (W5500), LoRa 433 MHz, microSD storage, RTC, USB-UART console/debug interface (CP2102N), and isolated RS485 ports using ADM2587 transceivers. The design includes ESP32-S3-WROOM-1-N16R2 as the main controller, W5500 Ethernet, LoRa antenna interface, microSD connector, RTC circuitry, CP2102N USB-to-UART programming/debug console, SC16IS752 UART expanders, isolated RS485 channels, power regulation, ESD/surge protection, connectors, and mounting holes. Cellular/BG95/SIM functionality and true RS232 console hardware are not included; J1 is used only as the microSD card connector.

DIN-rail ESP32-S3 mains-powered controller with isolated 5 V supply, Ethernet RJ45, USB-C service port, and central LED module connector.

An I2C extension board with LTC4311 bus accelerator and shielded ethernet port. This board is for the target side. With proper controller side hardware and an SSTP ethernet cable, the board provides robust i2c communication over 10ft(could be longer, haven't tested it yet) with a bitrate of 400kHz under a noisy environment( near motors, power cables, switches, etc). The breakout board receives power from the controller side and can power i2c device. The board also supports drdy trigger, which is available on many i2c sensors. #project #I2C #shielded #robust #ltc4311 #long-distance

Industrial 24 V DC MESBox controller with embedded Linux SOM, STM32 real-time I/O, triple RJ45 Ethernet, TFT display, isolated inputs, protected transistor outputs, offline memory, surge/reverse-polarity protection, and EMC-focused layout constraints.

ESP32-S3 Industrial PLC Controller schematic architecture for a 24 V industrial PLC with W5500 Ethernet, isolated RS485, 8 opto-isolated digital inputs, and 8 protected high-side outputs.

Per-channel low-voltage controller PCB for RIL TC/HF/LeTID and PID test benches. STM32H7, 16-bit DAC setpoints, 24-bit ADC sense (4-wire), isolated digital interface to gate driver, PT100/RH conditioning, Ethernet, interlocks. Safety-critical brain board.

CNC hydraulic press brake controller with STM32H743, ADS1256, 5x DAC8501 ±10V outputs, 3x AD598 LVDT interfaces, isolated 24V digital inputs, 100BASE-TX Ethernet, watchdog, E-stop hardware disable, and 4-layer 220mm x 160mm PCB architecture. Domains: field 24V I/O, precision analog, logic/Ethernet. Safety behavior: E-stop and valve-disable force all analog command outputs to 0V-safe state and disable field enables; watchdog and power-good supervisor reset MCU on comms or rail faults. PCB constraints: L1/L4 signal+components, L2 solid GND, L3 power plane, 1.0mm board inset margin, RJ45 at edge, field connectors on opposite edge, isolation corridor between field wiring and logic/Ethernet, 4x M4 plated mounting holes inset 10mm from corners.

The Atmel® | SMART SAM9260, manufactured by Atmel, is an ARM-based Embedded Microprocessor Unit (MPU), integrating the ARM926EJ-STM processor operating at 180 MHz. This MPU includes substantial on-chip memory and extensive peripherals, including an Ethernet MAC, USB Device and Host Ports, along with various standard interfaces such as USART, SPI, TWI, Timer Counters, and MultiMedia Card Interface. Architected on a 6-layer matrix delivering a maximum internal bandwidth of six 32-bit buses, it supports external 32-bit bus interfaces for SDRAM, static memories, CompactFlash, and SLC NAND Flash with ECC. The SAM9260 is available in 217-ball LFBGA and 208-pin PQFP packages. Key features include 8 Kbytes each of data and instruction cache, integrated MMU, two internal 4-Kbyte SRAMs, a 32-Kbyte ROM with bootloader, 22 Peripheral DMA channels, various power-on reset modes, two programmable clock signals, advanced interrupt controller, and multiple power management options for optimized performance and energy efficiency.