This is a reference design of ESP32-C3-MINI-1 based on the manufacturer's recommendations. On board we have an ESP module, USB C for firmware, 2 connectors with IOs and RGB LED #ESP32 #WiFi #LED #IoT #BLE #ARM #referenceDesign #simple-embedded #espressif #template #reference-design

Single-subsystem 3.3 V synchronous buck-boost regulator reference built around the TI TPS63802DLAR in a 10-pin VSON package. The design accepts a VBUS input rail into VIN, uses a Bourns SRP4020TA-4R7M 4.7 µH power inductor between L1/L2, and generates PP3V3 from the adjustable TPS63802 output path. The TPS63802 metadata lists a 1.3 V to 5.5 V input range, 2 A output current, selectable switching-frequency modes around 1.4 MHz to 2.1 MHz, and -40 °C to +125 °C junction operation. Support circuitry includes 22 µF and 1 µF ceramic input/output capacitors, a 511 kΩ / 91 kΩ feedback divider for the PP3V3_FB node, a VBUS-derived enable divider using 93.1 kΩ and 100 kΩ resistors, MODE tied to GND, and a 100 kΩ pull-up from PP3V3 to the power-good output. Intended as a reusable compact 3.3 V buck-boost power-supply module for USB, battery, portable, IoT, or embedded sensor designs.

This is a Pet Tracker Reference Design based on STM32L4. Tracker connects with network by SIM800L module connected to the STM. Also MCU connected to the GPS by uart and send data to server #STM32 #GPS #G4 #G3 #LTE #IoT #Tracker #smartHomeDevices #referenceDesign #edge-computing #edgeComputing #stm #template #referenceDesign

This is a BLE to WiFi gateway Reference Design. It employs an ESP32 microcontroller and an STM32WB5MMGH6TR for BLE functionality. The design includes connectors, multiple capacitors, resistors, switches, and LEDs. USB Type-C is used for power and data. This could be used for IoT purposes in home automation or wireless sensor data transmission. #referenceDesign #edge-computing #espressif #stm #template #ble #reference-design

This is a Pet Tracker Reference Design based on STM32L4. Tracker connects with network by SIM800L module connected to the STM. Also MCU connected to the GPS by uart and send data to server #STM32 #GPS #G4 #G3 #LTE #IoT #Tracker #smartHomeDevices #referenceDesign #edge-computing #edgeComputing #stm #template #referenceDesign

Nodo IoT de monitoreo energético distribuido basado en ESP32 DevKit para medición de voltaje, corriente y potencia con sensores SCT-013 y ZMPT101B, alimentación desde HLK-PM01, conversión a 3.3 V, protección/aislamiento y comunicación inalámbrica en tiempo real.

Compact 45 mm x 35 mm 4-layer agricultural IoT sensor node using an ATmega4808, AMS1117-3.3 linear regulation from 12 V input, RS-485 Modbus RTU half-duplex, local I2C sensors, 0.96 inch OLED, status LED, and a 12 V solenoid valve driver with top-side sensors/display and bottom-side MCU/power partitioning.

This is a Pet Tracker Reference Design based on STM32L4. Tracker connects with network by SIM800L module connected to the STM. Also MCU connected to the GPS by uart and send data to server #STM32 #GPS #G4 #G3 #LTE #IoT #Tracker #smartHomeDevices #referenceDesign #edge-computing #edgeComputing #stm #template #referenceDesign

This is a Pet Tracker Reference Design based on STM32L4. Tracker connects with network by SIM800L module connected to the STM. Also MCU connected to the GPS by uart and send data to server #STM32 #GPS #G4 #G3 #LTE #IoT #Tracker #smartHomeDevices #referenceDesign #edge-computing #edgeComputing #stm #template #referenceDesign

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #internetOfThings #smartHomeDevices #SeeedStudio #XIAO #LoRa #RP2040 #IoT

Smart Wellhead Controller V1.1: ESP32 + LoRa Industrial IoT Node with Solar Power, Deep-Sleep Leak Sensing, and OLED HMI. Now upgraded with a solar charging and battery management stage featuring a TP4056/CN3791 charger IC, power-path switching, Li-ion battery protection, and integrated 3.3 V rail supply. #PowerBlock #SolarCharging #BMS

This is an ESP32-C3 reference design based on the manufacturer's recommendations with a uFL SMD antenna and USB C on board #WiFi #ESP32-C3 #IoT #referenceDesign #simple-embedded #espressif #template #reference-design

A smart ESP32-based battery management system controller board for Lithium ion battery packs/cells. Capable of communicating to wide varieties of hybrid-smart inverters with CANbus, RS485 and UART communication. Inspired by the open-source project diyBMS by Stuart Pittaway #smartHomeDevices #esp32 #iot

This is an ESP32-C3 reference design based on the manufacturer's recommendations with a uFL SMD antenna and USB C on board #WiFi #ESP32-C3 #IoT #referenceDesign #simple-embedded #espressif #template #reference-design

Seeed Studio XIAO ESP32C6 is powered by the highly-integrated ESP32-C6 SoC, built on two 32-bit RISC-V processors, with a high-performance (HP) processor with running up to 160 MHz, and a low-power (LP) 32-bit RISC-V processor, which can be clocked up to 20 MHz. There are 512KB SRAM and 4 MB Flash on the chip, allowing for more programming space, and binging more possibilities to the IoT control scenarios.

This project uses an ESP32 microcontroller and OV2640 camera to create a WiFi-enabled digital camera. It uses AMS1117 voltage regulators to provide regulated power, a CH340C for USB communication, and includes capacitors and resistors for circuit balance. Ideal for IoT and edge computing tasks. #referenceDesign #project #ESP32 #ESP32WROVER #RF #WIFI #MCU #referenceDesign #edge-computing #edgeComputing #espressif #template #reference-design

This is a ESP32-C3-WROOM-02U reference design based on the manufacturer's recommendations. On board we have an ESP module, USB C for firmware, 2 connectors with IOs and RGB LED #ESP32 #WiFi #LED #IoT #BLE #ARM #referenceDesign #simple-embedded #espressif #template

This is a ESP32-C3-WROOM-02U reference design based on the manufacturer's recommendations. On board we have an ESP module, USB C for firmware, 2 connectors with IOs and RGB LED #ESP32 #WiFi #LED #IoT #BLE #ARM #referenceDesign #simple-embedded #espressif #template

This is a project of an energy-efficient temperature and humidity sensor that works via Zigbee #Zigbee #sensor #iot #template #project

This is a project of an energy-efficient temperature and humidity sensor that works via Zigbee #Zigbee #sensor #iot #template #project

This is a Pet Tracker Reference Design based on STM32L4. Tracker connects with network by SIM800L module connected to the STM. Also MCU connected to the GPS by uart and send data to server #STM32 #GPS #G4 #G3 #LTE #IoT #Tracker #smartHomeDevices #referenceDesign #edge-computing #edgeComputing #stm #template #referenceDesign

This is a Pet Tracker Reference Design based on STM32L4. Tracker connects with network by SIM800L module connected to the STM. Also MCU connected to the GPS by uart and send data to server #STM32 #GPS #G4 #G3 #LTE #IoT #Tracker #smartHomeDevices #referenceDesign #edge-computing #edgeComputing #stm #template #referenceDesign

This is a WiFi relay board based on ESP32-H2 WiFi module. It have AC-DC power supply with output 12V and relay for controlling voltage #esp32 #project #Relay #wifi #esp32-h2 #iot #template

This is a Pet Tracker Reference Design based on STM32L4. Tracker connects with network by SIM800L module connected to the STM. Also MCU connected to the GPS by uart and send data to server #STM32 #GPS #G4 #G3 #LTE #IoT #Tracker #smartHomeDevices #referenceDesign #edge-computing #edgeComputing #stm #template #referenceDesign

The "Green Dot 2040E5" Board is a Node that interfaces RS485 Sensor probes and can log information to the cloud using LoRa Connectivity. It uses the XIAO RP2040 and the LoRa-E5 (STM32WLE5JC) modules from Seeed Studio to do its magic. It also has amazing power management capabilities (Solar charging, Battery protection, etc) that make it very useful for IoT applications #Seeed #XIOA #LoRa #RP2040 #IoT