Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

The Atmel® | SMART SAM9260, manufactured by Atmel, is an ARM-based Embedded Microprocessor Unit (MPU), integrating the ARM926EJ-STM processor operating at 180 MHz. This MPU includes substantial on-chip memory and extensive peripherals, including an Ethernet MAC, USB Device and Host Ports, along with various standard interfaces such as USART, SPI, TWI, Timer Counters, and MultiMedia Card Interface. Architected on a 6-layer matrix delivering a maximum internal bandwidth of six 32-bit buses, it supports external 32-bit bus interfaces for SDRAM, static memories, CompactFlash, and SLC NAND Flash with ECC. The SAM9260 is available in 217-ball LFBGA and 208-pin PQFP packages. Key features include 8 Kbytes each of data and instruction cache, integrated MMU, two internal 4-Kbyte SRAMs, a 32-Kbyte ROM with bootloader, 22 Peripheral DMA channels, various power-on reset modes, two programmable clock signals, advanced interrupt controller, and multiple power management options for optimized performance and energy efficiency.

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Naze 32 Revision 6 Flight Controller Schematic At the heart of the Naze32 is a 32bit ST micro work horse of a processor, with untapped memory and cpu power and a host of equally impressive sensors. The Naze is also matched up with some of the nicest GUI programs and features to get the most out of your configuration. Naze32 rev6 Features: USB on right side PPM/PWM input as through-hole 3.3V, I2C on standard-size headers Fully pinout compatible with rev5 accessories (OSDoge etc) SBUS Inverter Spectrum satellite MPU6500 Sonar pads w/resistors added for direct connection to 5V sonar All extra pads (FT, GP, A5) on top, only sonar on bottom BMP280 barometer 16mbit flash Guide: https://www.dronetrest.com/t/naze-32-revision-6-flight-controller-guide/1605

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Here's a template for the popular ESP-8266EX microcontroller board, wemos D1 mini. A mini wifi board with 4MB flash based on ESP-8266EX #wemos #esp8266 #project-template #template

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Example project for an Arduino MKR shield. It adds an external flash memory to the Arduino MKR. Based on the Arduino MKR Shield template. #project #arduino #shield #MKR

Simple 5V 555 timer astable LED flasher with red indicator LED, 5V terminal input, timing passives, and local bypass capacitors.

Flashlight controlled by attiny85. Still needs power switch/brightness control

Lethal Company Pro Flashlight [Find the acompanying button board here](https://www.flux.ai/markwuflux/lethal-company-pro-flashlight-button-board) TODO: ADD A BUTTON!! -Ultra bright -Makes click noise from speaker -Wirelessly transmits battery life (maybe use Ubo to receive this) -Drive a SST-40 Chinese LED I want this thing to be super bright! The brighter the better, but keep it simple. These LEDs will draw a lot of power, so we need some sort of CC source. It doesn't have to have high bandwidth. I am thinking about a DIY microcontroller buck converter with PID duty cycle control.

High Brightness Strobe/Flashing LED lights. Good for cyclists, e-bikes who bike at night.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Welcome to your new project. Imagine what you can build here.

Hand-solderable 9V battery powered 555 timer circuit that blinks a red LED once per second through an on/off switch.

Welcome to your new project. Imagine what you can build here.