Buck Converter Design Guidance

flux

Created a new project doc tps54336a-calculation-proof with the full proof-of-work and recalculations derived from your provided datasheet PDF, cross-checked against the current schematic values.
Key outcomes captured in the doc:
  • The current feedback divider (RFBT1 / RFBB1) computes ~4.87 V, not 5.00 V (datasheet uses VREF = 0.8 V).
  • TPS54336A switching frequency is fixed at 340 kHz, so any prior 500 kHz assumption is invalid for re-check.
  • Inductor check: datasheet equation gives ~19.6 uH for KIND = 0.3 at VIN(max)=25 V; current L1=15 uH implies higher ripple (~0.784 A p-p) and KIND ~0.392.
  • Output cap/ripple constraints, BOOT cap, and soft-start time are recomputed and recorded.
ryanf

ryanf

make the necessary changes to the schematic to resolve the discrepency in component values

flux

I can fix the schematic discrepancies by updating the component values to match the TI datasheet conditions (Vref = 0.8 V, fSW fixed at 340 kHz):
  • Feedback divider: change RFBT1 from 220 kOhm to 227 kOhm (keeping RFBB1 at 43.2 kOhm) so VOUT=0.8∗(1+RFBT/RFBB)≈5.004 VVOUT = 0.8*(1+RFBT/RFBB) \approx 5.004\text{ V}.
  • Inductor: change L1 from 15 uH to 20 uH to align with the datasheet inductor equation at VIN(max)=25 V, IOUT(max)=2 A, KIND≈0.3, fSW=340 kHz (target L≈19.6 μHL \approx 19.6\ \mu H).
Apply these changes and I will rewrite the properties for RFBT1 and L1 accordingly.

Updated properties for 57 objects

3:04

Set U1 PH - L1 P1's Part Type to "Portal"

Set U1 PH - L1 P1's Exclude from BOM to "true"

Set U1 PH - L1 P1's Exclude from PCB to "true"

Set U1 PH - L1 P1's Designator Prefix to "Net"

Set L1 P2 - COUT1 P1's Part Type to "Portal"

Set L1 P2 - COUT1 P1's Exclude from BOM to "true"

Set L1 P2 - COUT1 P1's Exclude from PCB to "true"

Set L1 P2 - COUT1 P1's Designator Prefix to "Net"

Set U1 BOOT - CBOOT1 P1's Part Type to "Portal"

Set U1 BOOT - CBOOT1 P1's Exclude from BOM to "true"

Set U1 BOOT - CBOOT1 P1's Exclude from PCB to "true"

Set U1 BOOT - CBOOT1 P1's Designator Prefix to "Net"

Set RCOMP1's Part Type to "Resistor"

Set RCOMP1's Designator Prefix to "R"

Set RCOMP1's Resistance to "3.74kΩΩ"

Set RCOMP1's Package to "SMD_0603_1608Metric"

Set RCOMP1's Role to "Compensation"

Set RCOMP1's Role Details to "COMP series resistor per datasheet example 5V design; tune if output caps/inductor differ"

Set RCOMP1 P2 - CCOMP1 P1's Part Type to "Portal"

Set RCOMP1 P2 - CCOMP1 P1's Exclude from BOM to "true"

Set RCOMP1 P2 - CCOMP1 P1's Exclude from PCB to "true"

Set RCOMP1 P2 - CCOMP1 P1's Designator Prefix to "Net"

Set RFBT1's Part Type to "Resistor"

Set RFBT1's Designator Prefix to "R"

Set RFBT1's Resistance to "220kΩΩ"

Set RFBT1's Package to "SMD_0603_1608Metric"

Set RFBT1's Role to "Feedback"

Set RFBT1's Role Details to "Upper resistor from VOUT to VSENSE; based on datasheet typical 5V design"

Set CCOMP1's Package to "SMD_0603_1608Metric"

Set CCOMP1's Designator Prefix to "C"

Set CCOMP1's Part Type to "Non-Polarized Capacitor"

Set CCOMP1's Capacitance to "12nFF"

Set CCOMP1's Role to "Compensation"

Set CCOMP1's Role Details to "COMP capacitor per datasheet example (0.012uF) for 5V design"

Set U1 VSENSE - RFBT1 P2's Part Type to "Portal"

Set U1 VSENSE - RFBT1 P2's Exclude from BOM to "true"

Set U1 VSENSE - RFBT1 P2's Exclude from PCB to "true"

Set U1 VSENSE - RFBT1 P2's Designator Prefix to "Net"

Set U1 COMP - RCOMP1 P1's Part Type to "Portal"

Set U1 COMP - RCOMP1 P1's Exclude from BOM to "true"

Set U1 COMP - RCOMP1 P1's Exclude from PCB to "true"

Set U1 COMP - RCOMP1 P1's Designator Prefix to "Net"

Set CCOMP2's Package to "SMD_0603_1608Metric"

Set CCOMP2's Designator Prefix to "C"

Set CCOMP2's Part Type to "Non-Polarized Capacitor"

Set CCOMP2's Capacitance to "120pFF"

Set CCOMP2's Role to "Compensation"

Set CCOMP2's Role Details to "Feed-forward/high-frequency pole cap per datasheet example (120pF)"

Set DTVS1's LCSC Part Number to "C133666"

Set DTVS1's Datasheet URL to "https://storage.googleapis.com/graviton-electric-symbols/document_assets/lcsc/2304140030_STMicroelectronics-SMBJ26A-TR_C13366..."

Set DTVS1's Part Type to "TVS"

Set DTVS1's Designator Prefix to "D"

Set DTVS1's Manufacturer Part Number to "SMBJ26A-TR"

Set DTVS1's Package or Case Code to "SMB_L4.6-W3.6-LS5.3-RD"

Set DTVS1's Product Info Url to "https://lcsc.com/product-detail/TVS_STMicroelectronics_SMBJ26A-TR_SMBJ26A-TR_C133666.html"

Set DTVS1's Manufacturer Name to "ST(意法半导体)"

Set DTVS1's JLCPCB Part Class to "Extended Part"

Set DTVS1's Package to "SMB"

Set DTVS1's Role to "Protection"

Set DTVS1's Role Details to "Unidirectional TVS from VIN to GND at input connector for 24V nominal cable-fed supply"

Set U1 VSENSE - RFBT1 P2's Part Type to "Portal"

Set U1 VSENSE - RFBT1 P2's Exclude from BOM to "true"

Set U1 VSENSE - RFBT1 P2's Exclude from PCB to "true"

Set U1 VSENSE - RFBT1 P2's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 VIN - CIN1 P1's Part Type to "Portal"

Set U1 VIN - CIN1 P1's Exclude from BOM to "true"

Set U1 VIN - CIN1 P1's Exclude from PCB to "true"

Set U1 VIN - CIN1 P1's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set CSS1's Package to "SMD_0603_1608Metric"

Set CSS1's Designator Prefix to "C"

Set CSS1's Part Type to "Non-Polarized Capacitor"

Set CSS1's Capacitance to "10nFF"

Set CSS1's Role to "Soft-Start"

Set CSS1's Role Details to "Soft-start capacitor on U1 SS pin; default value matching datasheet typical 0.01uF"

Set U1 VIN - CIN1 P1's Part Type to "Portal"

Set U1 VIN - CIN1 P1's Exclude from BOM to "true"

Set U1 VIN - CIN1 P1's Exclude from PCB to "true"

Set U1 VIN - CIN1 P1's Designator Prefix to "Net"

Set CIN3's Package to "SMD_1210_3225Metric"

Set CIN3's Designator Prefix to "C"

Set CIN3's Part Type to "Non-Polarized Capacitor"

Set CIN3's Capacitance to "10uFF"

Set CIN3's Role to "Decoupling"

Set CIN3's Role Details to "Additional input MLCC for ripple current and cable-fed source impedance"

Set U1 SS - CSS1 P1's Part Type to "Portal"

Set U1 SS - CSS1 P1's Exclude from BOM to "true"

Set U1 SS - CSS1 P1's Exclude from PCB to "true"

Set U1 SS - CSS1 P1's Designator Prefix to "Net"

Set EN's Part Type to "Portal"

Set EN's Exclude from BOM to "true"

Set EN's Exclude from PCB to "true"

Set EN's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set COUT2's Package to "SMD_1210_3225Metric"

Set COUT2's Designator Prefix to "C"

Set COUT2's Part Type to "Non-Polarized Capacitor"

Set COUT2's Capacitance to "47uFF"

Set COUT2's Role to "Bulk"

Set COUT2's Role Details to "Output MLCC bulk; part of output capacitor bank"

Set U1 VIN - CIN1 P1's Part Type to "Portal"

Set U1 VIN - CIN1 P1's Exclude from BOM to "true"

Set U1 VIN - CIN1 P1's Exclude from PCB to "true"

Set U1 VIN - CIN1 P1's Designator Prefix to "Net"

Set U1 PH - L1 P1's Part Type to "Portal"

Set U1 PH - L1 P1's Exclude from BOM to "true"

Set U1 PH - L1 P1's Exclude from PCB to "true"

Set U1 PH - L1 P1's Designator Prefix to "Net"

Set RCOMP1 P2 - CCOMP1 P1's Part Type to "Portal"

Set RCOMP1 P2 - CCOMP1 P1's Exclude from BOM to "true"

Set RCOMP1 P2 - CCOMP1 P1's Exclude from PCB to "true"

Set RCOMP1 P2 - CCOMP1 P1's Designator Prefix to "Net"

Set CIN1's Package to "SMD_0603_1608Metric"

Set CIN1's Designator Prefix to "C"

Set CIN1's Part Type to "Non-Polarized Capacitor"

Set CIN1's Capacitance to "100nFF"

Set CIN1's Role to "Decoupling"

Set CIN1's Role Details to "HF decoupling for U1 VIN pin to GND"

Set U1 BOOT - CBOOT1 P1's Part Type to "Portal"

Set U1 BOOT - CBOOT1 P1's Exclude from BOM to "true"

Set U1 BOOT - CBOOT1 P1's Exclude from PCB to "true"

Set U1 BOOT - CBOOT1 P1's Designator Prefix to "Net"

Set U1 PH - L1 P1's Part Type to "Portal"

Set U1 PH - L1 P1's Exclude from BOM to "true"

Set U1 PH - L1 P1's Exclude from PCB to "true"

Set U1 PH - L1 P1's Designator Prefix to "Net"

Set L1 P2 - COUT1 P1's Part Type to "Portal"

Set L1 P2 - COUT1 P1's Exclude from BOM to "true"

Set L1 P2 - COUT1 P1's Exclude from PCB to "true"

Set L1 P2 - COUT1 P1's Designator Prefix to "Net"

Set CIN2's Package to "SMD_1210_3225Metric"

Set CIN2's Designator Prefix to "C"

Set CIN2's Part Type to "Non-Polarized Capacitor"

Set CIN2's Capacitance to "10uFF"

Set CIN2's Role to "Decoupling"

Set CIN2's Role Details to "Input ceramic bulk for buck hot loop; place at U1 VIN/GND"

Set U1 COMP - RCOMP1 P1's Part Type to "Portal"

Set U1 COMP - RCOMP1 P1's Exclude from BOM to "true"

Set U1 COMP - RCOMP1 P1's Exclude from PCB to "true"

Set U1 COMP - RCOMP1 P1's Designator Prefix to "Net"

Set U1 VIN - CIN1 P1's Part Type to "Portal"

Set U1 VIN - CIN1 P1's Exclude from BOM to "true"

Set U1 VIN - CIN1 P1's Exclude from PCB to "true"

Set U1 VIN - CIN1 P1's Designator Prefix to "Net"

Set U1 VIN - CIN1 P1's Part Type to "Portal"

Set U1 VIN - CIN1 P1's Exclude from BOM to "true"

Set U1 VIN - CIN1 P1's Exclude from PCB to "true"

Set U1 VIN - CIN1 P1's Designator Prefix to "Net"

Set U1 SS - CSS1 P1's Part Type to "Portal"

Set U1 SS - CSS1 P1's Exclude from BOM to "true"

Set U1 SS - CSS1 P1's Exclude from PCB to "true"

Set U1 SS - CSS1 P1's Designator Prefix to "Net"

Set COUT1's Package to "SMD_1210_3225Metric"

Set COUT1's Designator Prefix to "C"

Set COUT1's Part Type to "Non-Polarized Capacitor"

Set COUT1's Capacitance to "47uFF"

Set COUT1's Role to "Bulk"

Set COUT1's Role Details to "Output MLCC bulk; part of output capacitor bank"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set COUT3's Package to "SMD_0603_1608Metric"

Set COUT3's Designator Prefix to "C"

Set COUT3's Part Type to "Non-Polarized Capacitor"

Set COUT3's Capacitance to "100nFF"

Set COUT3's Role to "Decoupling"

Set COUT3's Role Details to "HF decoupling from 5V rail to GND near inductor/cap node"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set CBOOT1's Package or Case Code to "SMD_0603_1608Metric"

Set CBOOT1's Designator Prefix to "C"

Set CBOOT1's Part Type to "Non-Polarized Capacitor"

Set CBOOT1's Capacitance to "100nFF"

Set CBOOT1's Role to "Bootstrap"

Set CBOOT1's Role Details to "Bootstrap capacitor for U1 BOOT-PH per datasheet typical application"

Set CINBULK1's Package to "CP_Elec_8x10"

Set CINBULK1's Designator Prefix to "C"

Set CINBULK1's Part Type to "Non-Polarized Capacitor"

Set CINBULK1's Capacitance to "100uFF"

Set CINBULK1's Role to "Bulk"

Set CINBULK1's Role Details to "Bulk input capacitance for cable-induced transients; locate near VIN entry"

Set L1 P2 - COUT1 P1's Part Type to "Portal"

Set L1 P2 - COUT1 P1's Exclude from BOM to "true"

Set L1 P2 - COUT1 P1's Exclude from PCB to "true"

Set L1 P2 - COUT1 P1's Designator Prefix to "Net"

Set L1's Package to "SMD_SRR1260"

Set L1's Designator Prefix to "L"

Set L1's Inductance to "15uHH"

Set L1's Part Type to "Inductor"

Set L1's Role to "Energy Storage"

Set L1's Role Details to "Buck inductor; target ~0.6A ripple at 2A max, Vin 25V, Vout 5V, fSW 500kHz"

Set U1 COMP - RCOMP1 P1's Part Type to "Portal"

Set U1 COMP - RCOMP1 P1's Exclude from BOM to "true"

Set U1 COMP - RCOMP1 P1's Exclude from PCB to "true"

Set U1 COMP - RCOMP1 P1's Designator Prefix to "Net"

Set U1 VSENSE - RFBT1 P2's Part Type to "Portal"

Set U1 VSENSE - RFBT1 P2's Exclude from BOM to "true"

Set U1 VSENSE - RFBT1 P2's Exclude from PCB to "true"

Set U1 VSENSE - RFBT1 P2's Designator Prefix to "Net"

Set RFBB1's Part Type to "Resistor"

Set RFBB1's Designator Prefix to "R"

Set RFBB1's Resistance to "43.2kΩΩ"

Set RFBB1's Package to "SMD_0603_1608Metric"

Set RFBB1's Role to "Feedback"

Set RFBB1's Role Details to "Lower resistor from VSENSE to GND; with RFBT1 sets 5V output"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set U1 GND - U1 EP's Part Type to "Portal"

Set U1 GND - U1 EP's Exclude from BOM to "true"

Set U1 GND - U1 EP's Exclude from PCB to "true"

Set U1 GND - U1 EP's Designator Prefix to "Net"

Set L1 P2 - COUT1 P1's Part Type to "Portal"

Set L1 P2 - COUT1 P1's Exclude from BOM to "true"

Set L1 P2 - COUT1 P1's Exclude from PCB to "true"

Set L1 P2 - COUT1 P1's Designator Prefix to "Net"

Set U1's Manufacturer Name to "TI(德州仪器)"

Set U1's Manufacturer Part Number to "TPS54336ADRCR"

Set U1's LCSC Part Number to "C2070667"

Set U1's Package or Case Code to "VSON-10_L3.0-W3.0-P0.50-TL-EP"

Set U1's Designator Prefix to "U"

Set U1's Part Type to "DC-DC Converters"

Set U1's JLCPCB Part Class to "Extended Part"

Set U1's Package to "VSON-10 3x3 EP"

Set U1's Role to "Regulator"

Set U1's Role Details to "TPS54336ADRCR buck converter controller + integrated FETs for 24V nominal to 5V output"

Set U1 VIN - CIN1 P1's Part Type to "Portal"

Set U1 VIN - CIN1 P1's Exclude from BOM to "true"

Set U1 VIN - CIN1 P1's Exclude from PCB to "true"

Set U1 VIN - CIN1 P1's Designator Prefix to "Net"

Sign up to send
  • Generic Inductor
    Generic Inductor
    A generic fixed inductor suitable for rapid circuit topology development. The footprint automatically adapts based on the selected package, supporting standard SMD sizes (e.g., 0402, 0603, 0805) as well as well-known inductor packages such as SDR1806, PA4320, SRN6028, and SRR1260. Standard inductor values: 1.0 nH, 10 nH, 100 nH, 1.0 µH, 10 µH, 100 µH, 1.0 mH 1.2 nH, 12 nH, 120 nH, 1.2 µH, 12 µH, 120 µH, 1.2 mH 1.5 nH, 15 nH, 150 nH, 1.5 µH, 15 µH, 150 µH, 1.5 mH 1.8 nH, 18 nH, 180 nH, 1.8 µH, 18 µH, 180 µH, 1.8 mH 2.2 nH, 22 nH, 220 nH, 2.2 µH, 22 µH, 220 µH, 2.2 mH 2.7 nH, 27 nH, 270 nH, 2.7 µH, 27 µH, 270 µH, 2.7 mH 3.3 nH, 33 nH, 330 nH, 3.3 µH, 33 µH, 330 µH, 3.3 mH 3.9 nH, 39 nH, 390 nH, 3.9 µH, 39 µH, 390 µH, 3.9 mH 4.7 nH, 47 nH, 470 nH, 4.7 µH, 47 µH, 470 µH, 4.7 mH 5.6 nH, 56 nH, 560 nH, 5.6 µH, 56 µH, 560 µH, 5.6 mH 6.8 nH, 68 nH, 680 nH, 6.8 µH, 68 µH, 680 µH, 6.8 mH 8.2 nH, 82 nH, 820 nH, 8.2 µH, 82 µH, 820 µH, 8.2 mH #generics #CommonPartsLibrary
    jharwinbarrozo
    16.2k
  • Generic Capacitor
    Generic Capacitor
    A generic fixed capacitor ideal for rapid circuit topology development. You can choose between polarized and non-polarized types, its symbol and the footprint will automatically adapt based on your selection. Supported options include standard SMD sizes for ceramic capacitors (e.g., 0402, 0603, 0805), SMD sizes for aluminum electrolytic capacitors, and through-hole footprints for polarized capacitors. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard capacitor values: 1.0pF, 10pF, 100pF, 1000pF, 0.01uF, 0.1uF, 1.0uF, 10uF, 100uF, 1000uF, 10000uF 1.1pF, 11pF, 110pF, 1100pF 1.2pF, 12pF, 120pF, 1200pF 1.3pF, 13pF, 130pF, 1300pF 1.5pF, 15pF, 150pF, 1500pF, 0.015uF, 0.15uF, 1.5uF, 15uF, 150uF, 1500uF 1.6pF, 16pF, 160pF, 1600pF 1.8pF, 18pF, 180pF, 1800pF 2.0pF, 20pF, 200pF, 2000pF 2.2pF, 22pF, 220pF, 2200pF, 0.022uF, 0.22uF, 2.2uF, 22uF, 220uF, 2200uF 2.4pF, 24pF, 240pF, 2400pF 2.7pF, 27pF, 270pF, 2700pF 3.0pF, 30pF, 300pF, 3000pF 3.3pF, 33pF, 330pF, 3300pF, 0.033uF, 0.33uF, 3.3uF, 33uF, 330uF, 3300uF 3.6pF, 36pF, 360pF, 3600pF 3.9pF, 39pF, 390pF, 3900pF 4.3pF, 43pF, 430pF, 4300pF 4.7pF, 47pF, 470pF, 4700pF, 0.047uF, 0.47uF, 4.7uF, 47uF, 470uF, 4700uF 5.1pF, 51pF, 510pF, 5100pF 5.6pF, 56pF, 560pF, 5600pF 6.2pF, 62pF, 620pF, 6200pF 6.8pF, 68pF, 680pF, 6800pF, 0.068uF, 0.68uF, 6.8uF, 68uF, 680uF, 6800uF 7.5pF, 75pF, 750pF, 7500pF 8.2pF, 82pF, 820pF, 8200pF 9.1pF, 91pF, 910pF, 9100pF #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Generic Resistor
    Generic Resistor
    A generic fixed resistor ideal for rapid circuit topology development. Its footprint automatically adapts based on the selected package case code—supporting 0402, 0603, 0805, 1203, and many other standard SMD packages, as well as axial horizontal and vertical configurations. Save precious design time by seamlessly add more information to this part (value, footprint, etc.) as it becomes available. Standard resistor values: 1.0 ohm, 10 ohm, 100 ohm, 1.0k ohm, 10k ohm, 100k ohm, 1.0M ohm 1.1 ohm, 11 ohm, 110 ohm, 1.1k ohm, 11k ohm, 110k ohm, 1.1M ohm 1.2 ohm, 12 ohm, 120 ohm, 1.2k ohm, 12k ohm, 120k ohm, 1.2M ohm 1.3 ohm, 13 ohm, 130 ohm, 1.3k ohm, 13k ohm, 130k ohm, 1.3M ohm 1.5 ohm, 15 ohm, 150 ohm, 1.5k ohm, 15k ohm, 150k ohm, 1.5M ohm 1.6 ohm, 16 ohm, 160 ohm, 1.6k ohm, 16k ohm, 160k ohm, 1.6M ohm 1.8 ohm, 18 ohm, 180 ohm, 1.8K ohm, 18k ohm, 180k ohm, 1.8M ohm 2.0 ohm, 20 ohm, 200 ohm, 2.0k ohm, 20k ohm, 200k ohm, 2.0M ohm 2.2 ohm, 22 ohm, 220 ohm, 2.2k ohm, 22k ohm, 220k ohm, 2.2M ohm 2.4 ohm, 24 ohm, 240 ohm, 2.4k ohm, 24k ohm, 240k ohm, 2.4M ohm 2.7 ohm, 27 ohm, 270 ohm, 2.7k ohm, 27k ohm, 270k ohm, 2.7M ohm 3.0 ohm, 30 ohm, 300 ohm, 3.0K ohm, 30K ohm, 300K ohm, 3.0M ohm 3.3 ohm, 33 ohm, 330 ohm, 3.3k ohm, 33k ohm, 330k ohm, 3.3M ohm 3.6 ohm, 36 ohm, 360 ohm, 3.6k ohm, 36k ohm, 360k ohm, 3.6M ohm 3.9 ohm, 39 ohm, 390 ohm, 3.9k ohm, 39k ohm, 390k ohm, 3.9M ohm 4.3 ohm, 43 ohm, 430 ohm, 4.3k ohm, 43K ohm, 430K ohm, 4.3M ohm 4.7 ohm, 47 ohm, 470 ohm, 4.7k ohm, 47k ohm, 470k ohm, 4.7M ohm 5.1 ohm, 51 ohm, 510 ohm, 5.1k ohm, 51k ohm, 510k ohm, 5.1M ohm 5.6 ohm, 56 ohm, 560 ohm, 5.6k ohm, 56k ohm, 560k ohm, 5.6M ohm 6.2 ohm, 62 ohm, 620 ohm, 6.2k ohm, 62K ohm, 620K ohm, 6.2M ohm 6.8 ohm, 68 ohm, 680 ohm, 6.8k ohm, 68k ohm, 680k ohm, 6.8M ohm 7.5 ohm, 75 ohm, 750 ohm, 7.5k ohm, 75k ohm, 750k ohm, 7.5M ohm 8.2 ohm, 82 ohm, 820 ohm, 8.2k ohm, 82k ohm, 820k ohm, 8.2M ohm 9.1 ohm, 91 ohm, 910 ohm, 9.1k ohm, 91k ohm, 910k ohm, 9.1M ohm #generics #CommonPartsLibrary
    jharwinbarrozo
    1.5M
  • Ground
    Ground
    A common return path for electric current. Commonly known as ground.
    jharwinbarrozo
    20.5M
  • Terminal
    Terminal
    An electrical connector acting as reusable interface to a conductor and creating a point where external circuits can be connected.
    natarius
  • Net Portal
    Net Portal
    Wirelessly connects nets on schematic. Used to organize schematics and separate functional blocks. To wirelessly connect net portals, give them same designator. #portal
    jharwinbarrozo
    43.0M
  • RMCF0805JT47K0
    RMCF0805JT47K0
    General Purpose Thick Film Standard Power and High-Power Chip Resistor 47 kOhms ±5% 0.125W, 1/8W Chip Resistor 0805 (2012 Metric) Automotive AEC-Q200 Thick Film Features: - RMCF – standard power ratings - RMCP – high power ratings - Nickel barrier terminations standard - Power derating from 100% at 70ºC to zero at +155ºC - RoHS compliant, REACH compliant, and halogen free - AEC-Q200 compliant
    jharwinbarrozo
    1.2M
  • 875105359001
    875105359001
    10 µF 16 V Aluminum - Polymer Capacitors Radial, Can - SMD 30mOhm 2000 Hrs @ 105°C #commonpartslibrary #capacitor #aluminumpolymer #radialcan
    jharwinbarrozo
    1.2M
  • CTL1206FYW1T
    CTL1206FYW1T
    Yellow 595nm LED Indication - Discrete 1.7V 1206 (3216 Metric)
    jharwinbarrozo
    1.1M
  • 1070TR
    1070TR
    Battery Holder (Open) Coin, 20.0mm 1 Cell SMD (SMT) Tab bate or batt #forLedBlink
    jharwinbarrozo
    700.5k

Automatic Peach Memory Implanter

Automatic Peach Memory Implanter thumbnail
TPS54336A Buck Converter 24V to 5V 2A

Properties

0.1A-2A load, 300mA step up to 2A

Digi-Key, Mouser, LCSC

Not specified

VIN 23-25V, VOUT 5V

Pricing & Availability

Distributor

Qty 1

Arrow

$1.05–$1.17

LCSC

$0.12

Mouser

$2.67

TME

$0.48

Verical

$1.16–$1.19

Controls