Access Reader — важная правка по РАЗМЕЩЕНИЮ разъёмов (ты на placement): ВСЕ разъёмы и клеммники ставь ПО КРАЮ платы, ориентированными наружу, с зазором под вставку кабеля/штекера. Сейчас RJ45 Ethernet стоит ПОСЕРЕДИНЕ — в него физически не воткнуть провод, перемести на кромку. На край разъёмной стороной наружу: RJ45 (Ethernet), клеммник входа 9–32В DC, клеммники 2 реле (NO/NC/COM), сервисный USB, клеммники/хедеры RS-485, Wiegand и 2 входов, разъём/шлейф GM861 (QR), 2-pin разъём катушки 125к (J101). Вход кабеля не должен перекрываться компонентами, крепёжными отверстиями или соседними разъёмами (проверь высоту/вылет коннектора наружу за контур). Зону поднесения карт (антенны 13.56/125к) держи свободным краем без разъёмов. Это правило — жёсткое: неудобный доступ к разъёму = брак. Обнови placement и manufacturing notes, отметь этот constraint в ready-to-export чеклисте.
Что не удалось: пакет не order-ready — routing не завершён, DRC всё ещё показывает много airwires; stackup tool принял 4-layer, но readback показывает inner layers как Signal вместо GND/PWR; SS14 diode-OR работает как reverse-blocking fallback, но лучше заменить на ideal-diode/power-mux перед производством. Critical ERC по питанию/GND для W5500, USB ESD, LMR16020 и PoE/DC OR-ing исправлены, placement выполнен на 80×100 мм.
Full first Rev A prototype preserved: PoE AG9905-MTB, RJ45/W5500 Ethernet, 9-32 V DC LMR16020 branch and ESP32-S3 Wi-Fi are populated.
Critical ERC power errors were fixed: W5500 AVDD/AGND/support, USB ESD VBUS/GND/data lines, LMR16020 VIN/EN/BOOT/RT/EP, AG9905 PoE input/output, and Ethernet data pairs.
Added reverse-blocking diode-OR parts D7 and D8 from DC buck / PoE module outputs into the system 5 V rail. This is a functional Schottky diode-OR fallback; an ideal-diode/power-mux replacement remains recommended for lower drop.
Renamed common rails to 5V_SYS and 3V3_SYS and tagged key rails as power/ground.
Board was set to 80 x 100 mm with pcbfast/JLC-style 4-layer intent and 6 mil minimum rules.
Placement was run twice and then manually cleaned for remaining overlap issues.
Routing did not complete. The available targeted router blocked on dense 80 x 100 mm placement and there is no bulk autorouter tool exposed in this run.
DRC still reports hundreds of airwires; exported Gerbers therefore are not factory-order-ready.
Stackup was requested as Top/GND/PWR/Bottom; the tool accepted a 4-layer template but the stackup readback still shows inner layers typed as Signal instead of Ground Plane / Power Plane. This must be corrected before ordering.
80 x 100 mm is very dense for 113 physical layout components; tool reports routing congestion. A larger board, more bottom-side passives, or a manual/autorouted pass is needed.
The diode-OR implementation using SS14 is safe for reverse-blocking but drops voltage; replacing D7/D8 with an ideal-diode/power-mux stage remains recommended before production.
Do Not Send to pcbfast Yet
The generated files are a snapshot/export artifact for review, not a released manufacturing package. Do not order until routing is complete and DRC has no airwires, invalid layers, missing footprints, or cross-net copper conflicts.