Design Review and Compliance Analysis


I’ll read the uploaded WalkInPeace prompt, compare it against the current project state, then turn any actionable requirements into project-file notes or schematic/layout fixes as appropriate.
I read the uploaded prompt and updated WalkInPeace Design Review Notes with a compliance gap analysis.
Key finding: the uploaded prompt specifies a full bare-ADS1299 main board, but the current project is built around an ADS1299 breakout/module carrier, so matching the prompt requires a substantial schematic rebuild before layout/routing. Choose either A: keep the current module-based design and finish routing, or B: rebuild to match the uploaded bare-ADS1299 v1.0 prompt.
replace the bare asd1299 with ads1299 breakout
I’ll keep the design on the ADS1299 breakout approach. First I’ll verify whether a bare ADS1299 is still present, then update the schematic/docs only if anything still points to the bare-chip implementation.
I verified the schematic direction: the live design already uses an ADS1299 breakout/module header, not a bare ADS1299 IC. The breakout is J6, a 12-pin header with 3V3, GND, SPI, CS, DRDY, START, RESET, PWDN, BIAS/RLD, and reserved/CLK signals.
I was blocked by execution credits before updating the project files, but no schematic replacement was needed based on the live schematic. Remaining work: update the project notes/spec to remove the bare-ADS1299 option, confirm the exact ADS1299 breakout pinout matches J6, then resolve the current DRC airwires before manufacturing.
Check J6 pinout
Update project notes
Run ERC/DRC
Find breakout part

Firmware Starter — WalkInPeace ESP32-S3
Platform & Toolchain
  • MCU/module: ESP32-S3-WROOM-1-N16R8
  • Framework: Arduino on PlatformIO
  • Build system: PlatformIO
  • Main peripherals: ADS1299 breakout module over SPI, MPU-6050 over I2C, DRV2605L over I2C, buzzer GPIO, battery ADC
Pin Mapping

Table


FunctionESP32-S3 GPIONetDirectionNotes
I2C SDA4I2C_SDAbidirectionalMPU-6050 + DRV2605L, 4.7 kOhm pull-up
I2C SCL5I2C_SCLoutputMPU-6050 + DRV2605L, 4.7 kOhm pull-up
MPU-6050 INT14IMU_INTinputoptional interrupt
DRV2605L EN15HAPTIC_ENoutputenables haptic driver
Buzzer drive18BUZZER_GPIOoutputNMOS low-side switch
Battery monitor1BAT_ADCanalog input470k/470k divider; VBAT = ADC voltage x2
ADS1299 SCLK12ADS_SPI_SCLKoutputSPI clock
ADS1299 DIN/MOSI11ADS_SPI_MOSIoutputESP32 to ADS1299
ADS1299 DOUT/MISO13ADS_SPI_MISOinputADS1299 to ESP32
ADS1299 CS10ADS_CSoutputactive low
ADS1299 DRDY9ADS_DRDYinputactive low data-ready interrupt
ADS1299 START8ADS_STARToutputconversion control
ADS1299 RESET7ADS_RESEToutputactive low reset
ADS1299 PWDN6ADS_PWDNoutputactive low power-down
platformio.ini

Ini


[env:esp32-s3-devkitc-1]
platform = espressif32
board = esp32-s3-devkitc-1
framework = arduino
monitor_speed = 115200
build_flags =
  -D ARDUINO_USB_MODE=1
  -D ARDUINO_USB_CDC_ON_BOOT=1
lib_deps =
  adafruit/Adafruit MPU6050@^2.2.6
  adafruit/Adafruit Unified Sensor@^1.1.14
  adafruit/Adafruit DRV2605 Library@^1.2.4
Complete Firmware Source

Cpp


#include <Arduino.h>
#include <Wire.h>
#include <SPI.h>
#include <Adafruit_MPU6050.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_DRV2605.h>

// I2C
#define PIN_I2C_SDA        4
#define PIN_I2C_SCL        5
#define PIN_IMU_INT        14

// Alerts
#define PIN_HAPTIC_EN      15
#define PIN_BUZZER         18

// Battery ADC
#define PIN_BAT_ADC        1

// ADS1299 SPI/control
#define PIN_ADS_SCLK       12
#define PIN_ADS_MOSI       11
#define PIN_ADS_MISO       13
#define PIN_ADS_CS         10
#define PIN_ADS_DRDY       9
#define PIN_ADS_START      8
#define PIN_ADS_RESET      7
#define PIN_ADS_PWDN       6

#define DRV2605_ADDR       0x5A
#define MPU6050_ADDR       0x68

Adafruit_MPU6050 mpu;
Adafruit_DRV2605 drv;
SPIClass adsSpi(FSPI);

volatile bool adsDataReady = false;

void IRAM_ATTR onAdsDrdy() {
  adsDataReady = true;
}

uint8_t adsTransfer(uint8_t value) {
  return adsSpi.transfer(value);
}

void adsCommand(uint8_t cmd) {
  digitalWrite(PIN_ADS_CS, LOW);
  delayMicroseconds(2);
  adsTransfer(cmd);
  delayMicroseconds(2);
  digitalWrite(PIN_ADS_CS, HIGH);
}

uint8_t adsReadRegister(uint8_t reg) {
  digitalWrite(PIN_ADS_CS, LOW);
  delayMicroseconds(2);
  adsTransfer(0x20 | (reg & 0x1F)); // RREG
  adsTransfer(0x00);                // read 1 register
  delayMicroseconds(2);
  uint8_t value = adsTransfer(0x00);
  digitalWrite(PIN_ADS_CS, HIGH);
  return value;
}

void adsWriteRegister(uint8_t reg, uint8_t value) {
  digitalWrite(PIN_ADS_CS, LOW);
  delayMicroseconds(2);
  adsTransfer(0x40 | (reg & 0x1F)); // WREG
  adsTransfer(0x00);                // write 1 register
  adsTransfer(value);
  delayMicroseconds(2);
  digitalWrite(PIN_ADS_CS, HIGH);
}

void initAds1299() {
  pinMode(PIN_ADS_CS, OUTPUT);
  pinMode(PIN_ADS_START, OUTPUT);
  pinMode(PIN_ADS_RESET, OUTPUT);
  pinMode(PIN_ADS_PWDN, OUTPUT);
  pinMode(PIN_ADS_DRDY, INPUT_PULLUP);

  digitalWrite(PIN_ADS_CS, HIGH);
  digitalWrite(PIN_ADS_START, LOW);
  digitalWrite(PIN_ADS_PWDN, HIGH);
  digitalWrite(PIN_ADS_RESET, HIGH);

  adsSpi.begin(PIN_ADS_SCLK, PIN_ADS_MISO, PIN_ADS_MOSI, PIN_ADS_CS);
  delay(20);

  digitalWrite(PIN_ADS_RESET, LOW);
  delay(5);
  digitalWrite(PIN_ADS_RESET, HIGH);
  delay(20);

  adsCommand(0x11); // SDATAC: stop continuous read before register access
  delay(2);

  uint8_t id = adsReadRegister(0x00);
  Serial.print("ADS1299 ID register: 0x");
  Serial.println(id, HEX);

  // Conservative bring-up only. Final gain/sample-rate setup should match the module and study protocol.
  attachInterrupt(digitalPinToInterrupt(PIN_ADS_DRDY), onAdsDrdy, FALLING);
}

void initImu() {
  pinMode(PIN_IMU_INT, INPUT);
  if (!mpu.begin(MPU6050_ADDR, &Wire)) {
    Serial.println("MPU-6050 not detected");
    return;
  }
  mpu.setAccelerometerRange(MPU6050_RANGE_4_G);
  mpu.setGyroRange(MPU6050_RANGE_500_DEG);
  mpu.setFilterBandwidth(MPU6050_BAND_44_HZ);
  Serial.println("MPU-6050 initialized");
}

void initHaptics() {
  pinMode(PIN_HAPTIC_EN, OUTPUT);
  digitalWrite(PIN_HAPTIC_EN, HIGH);

  if (!drv.begin(&Wire)) {
    Serial.println("DRV2605L not detected");
    return;
  }
  drv.selectLibrary(6);       // LRA library family; tune during testing
  drv.setMode(DRV2605_MODE_INTTRIG);
  Serial.println("DRV2605L initialized");
}

void playHapticAlert() {
  digitalWrite(PIN_HAPTIC_EN, HIGH);
  drv.setWaveform(0, 47); // example strong click; tune for selected LRA
  drv.setWaveform(1, 0);
  drv.go();
}

void buzz(uint16_t ms) {
  digitalWrite(PIN_BUZZER, HIGH);
  delay(ms);
  digitalWrite(PIN_BUZZER, LOW);
}

float readBatteryVoltage() {
  uint16_t raw = analogRead(PIN_BAT_ADC);
  float adcV = (raw / 4095.0f) * 3.3f;
  return adcV * 2.0f; // 470k / 470k divider
}

void setup() {
  Serial.begin(115200);
  delay(1000);
  Serial.println("WalkInPeace firmware bring-up");

  pinMode(PIN_BUZZER, OUTPUT);
  digitalWrite(PIN_BUZZER, LOW);
  analogReadResolution(12);

  Wire.begin(PIN_I2C_SDA, PIN_I2C_SCL, 400000);

  initImu();
  initHaptics();
  initAds1299();

  buzz(80);
  playHapticAlert();
}

void loop() {
  static uint32_t lastPrint = 0;

  if (adsDataReady) {
    adsDataReady = false;
    // TODO: read ADS1299 sample frame according to selected data mode and channel configuration.
  }

  if (millis() - lastPrint > 1000) {
    lastPrint = millis();

    sensors_event_t a, g, temp;
    if (mpu.getEvent(&a, &g, &temp)) {
      Serial.print("Accel m/s^2: ");
      Serial.print(a.acceleration.x); Serial.print(", ");
      Serial.print(a.acceleration.y); Serial.print(", ");
      Serial.println(a.acceleration.z);
    }

    Serial.print("Battery V: ");
    Serial.println(readBatteryVoltage(), 3);
  }
}
Build & Flash

Bash


pio run
pio run -t upload
pio device monitor
Bring-Up Notes
  1. Power the board from battery only when electrodes are attached to a person.
  2. Verify the ADS1299 breakout module pin order matches J6 before plugging in the module.
  3. Confirm ADS1299 register values with the module vendor schematic/documentation before enabling continuous acquisition.
  4. Tune DRV2605L LRA library/effect settings for the selected actuator.
  • Platform & Toolchain

  • Pin Mapping

  • platformio.ini

  • Complete Firmware Source

  • Build & Flash

  • Bring-Up Notes