flux

#Goal

- Integrate an off‑board Arduino Uno and complete the schematic/BOM fixes by removing obsolete components, finalizing the 5 V DWIN UART connections, splitting the blower outputs (J1:6 and J1:7) to the correct rails, cleaning up generic parts in the BOM with assigned MPNs, and tidying the critical net names.

#Implementation plan

1. Remove Obsolete Components

1. Delete components U6, J3, U7, and U8 from the schematic to eliminate the on-board MCU path.

2. Verify that orphan nets resulting from these deletions are correctly cleaned up.

2. Configure and Finalize UART Connection

1. Update the UART header J4: set its part number (MPN) to Molex 0022288040.

2. Wire the off‑board Arduino connection through R1 and R2 in series with U9 to route the UART signals from off‑board header J5 to J4.

3. Tie J4 VCC to +5V and J4 GND to LV_GND to complete the power and ground connections.

3. Split Blower Outputs

1. Route Q2:A2 exclusively to terminal J1:6 and Q3:A2 exclusively to terminal J1:7.

2. Confirm that the signal paths are only connected to the appropriate AC rails: connect AC_HOT_IN and AC_NEUTRAL to the correct blocks (J1:4/J1:1/3, etc.) as per design requirements.

3. Ensure the MOV series F1 continues routing to J2:4 for safety, if applicable.

4. Cleanup Generic Components in BOM

1. Assign specific MPNs to all remaining generic resistors and capacitors (including R1-R12, C5-C8, C10-C11, R25, etc.) using standard manufacturer parts (e.g., Yageo, Murata, TDK) available in the parts library.

2. Verify the footprints and component values remain consistent with their schematic symbols.

5. Rename Critical Nets and Validate Design

1. Rename nets to standard names: +5V, LV_GND, IGNITER_TRIAC_OUT, BLOWER1_HOT_OUT, BLOWER2_HOT_OUT, and AUGER_HOT_OUT.

2. Run the ERC and DRC checks in the Flux environment and verify that the circuit design meets all electrical and layout requirements without errors.

#Success criteria

- Obsolete components (U6, J3, U7, U8) are completely removed with no orphaned nets.

- The UART interface is finalized with J4 set to Molex 0022288040 and connected correctly via R1/R2 and U9, with proper VCC and GND routing.

- Blower outputs are split appropriately with Q2:A2 connected to J1:6 and Q3:A2 connected to J1:7, with the AC rails correctly configured.

- All generic BOM parts have assigned MPNs and consistent footprints/values.

- The net names are standardized, and all ERC/DRC checks pass without errors.

Added 1x 0022288040 as J6

Connected R1:P2 to J4:PIN_3

Connected R2:P2 to J4:PIN_4

Connected J5:P1, R1:P1, U9:~

Connected J5:P2, R2:P1, U9:~

Connected J4:PIN_2 to GND:GND

Connected J4:PIN_1 to PS1:+Vout

Disconnected J5:P1 from R1:P1

Disconnected J5:P2 from R2:P1

Disconnected Q3:A2 from J1:7

Disconnected Q4:A2 from J1:7

Set J4's Manufacturer Part Number to "0022288040"

Set J4's Manufacturer Name to "Molex"

Set R1's Manufacturer Part Number to "RC0603FR-0733RL"

Set R1's Manufacturer Name to "Yageo"

Set R2's Manufacturer Part Number to "RC0603FR-0733RL"

Set R2's Manufacturer Name to "Yageo"

Set R3's Manufacturer Part Number to "RC0603FR-0710KL"

Set R3's Manufacturer Name to "Yageo"

Set R4's Manufacturer Part Number to "RC0603FR-070RL"

Set R4's Manufacturer Name to "Yageo"

Set R5's Manufacturer Part Number to "RC0603FR-070RL"

Set R5's Manufacturer Name to "Yageo"

Set R6's Manufacturer Part Number to "RC0603FR-070RL"

Set R6's Manufacturer Name to "Yageo"

Set R7's Manufacturer Part Number to "RC0603FR-070RL"

Set R7's Manufacturer Name to "Yageo"

Set R8's Manufacturer Part Number to "RC0603FR-070RL"

Set R8's Manufacturer Name to "Yageo"

Set R9's Manufacturer Part Number to "RC0603FR-070RL"

Set R9's Manufacturer Name to "Yageo"

Set R10's Manufacturer Part Number to "RC0603FR-070RL"

Set R10's Manufacturer Name to "Yageo"

Set R11's Manufacturer Part Number to "RC0603FR-070RL"

Set R11's Manufacturer Name to "Yageo"

Set R12's Manufacturer Part Number to "RC0603FR-070RL"

Set R12's Manufacturer Name to "Yageo"

Set R25's Manufacturer Part Number to "RC0603FR-070RL"

Set R25's Manufacturer Name to "Yageo"

Set C5's Manufacturer Part Number to "CL10B104KB8NNNC"

Set C5's Manufacturer Name to "Samsung Electro-Mechanics"

Set C6's Manufacturer Part Number to "CL10B104KB8NNNC"

Set C6's Manufacturer Name to "Samsung Electro-Mechanics"

Set C7's Manufacturer Part Number to "CL10B104KB8NNNC"

Set C7's Manufacturer Name to "Samsung Electro-Mechanics"

Set C8's Manufacturer Part Number to "CL10B104KB8NNNC"

Set C8's Manufacturer Name to "Samsung Electro-Mechanics"

Set C10's Manufacturer Part Number to "CL10B104KB8NNNC"

Set C10's Manufacturer Name to "Samsung Electro-Mechanics"

Set C11's Manufacturer Part Number to "CL10B104KB8NNNC"

Set C11's Manufacturer Name to "Samsung Electro-Mechanics"