# From Breadboard to Boxed Product: A Step-by-Step Guide instrument maker turns an ultrasonic leak detector breadboard into a boxed field prototype for maintenance crews. Written by [Matthias Wagner](https://www.flux.ai/natarius) Published Oct 2026 - 6 min read ![From Breadboard to Boxed Product: A Step-by-Step Guide](https://www.flux.ai/p/assets/blogs/breadboard-to-boxed-product-guide/main.webp) A product manager keeps a breadboarded ultrasonic leak detector in a parts bin. The demo showed that a 40-kilohertz probe could reveal compressed-air leaks on a noisy factory floor; now the team needs a boxed prototype that can withstand a maintenance shift in a tool bag. The prototype had no defined battery, enclosure, trigger, or way to protect the piezo sensor. The OLED display hung from a long ribbon. Each time someone lifted the unit, the probe amplifier picked up a different amount of electrical noise. The product manager needed a boxed prototype that the technicians could carry, point at a valve, and understand without a lab engineer beside them. This guide follows the decisions her team made. It starts with the technician's job, then turns the bench circuit into a board and a physical tool. ## Name the measurement before drawing the outline The product manager watched a plant mechanic sweep the existing demo across a leaking pneumatic joint. The operator needed a rising bar and a tone when ultrasonic energy increased. The display had to remain readable under ceiling lights. A trigger had to start and freeze a measurement with one gloved hand. The tool needed to run through an eight-hour maintenance route and recharge at the end of a shift. The team recorded the probe frequency, input range, battery target, and display size. The circuit proposal used a 40-kilohertz piezo receiver, a TLV9062 low-noise amplifier, an STM32G474 microcontroller, an ADS8866 converter, and a small I2C OLED. A protected 18650 cell supplied the device. The first board envelope was 62 by 38 millimeters, with four layers to separate the high-impedance sensor input from the display and switching supply. The product manager asked the electrical engineer to separate the probe input, analog gain, conversion, user interface, and battery charging in the schematic. That made each breadboard jumper correspond to a named connection. They reviewed the amplifier datasheet and the ADC input range before moving the prototype circuit into a routed layout. Circuit simulation helped them inspect the filter response around the probe band. ## Put controls where a technician can reach them The first case sketch was a small rectangular box. The plant mechanic showed the product manager why that was awkward. A technician needed to hold the probe head close to a fitting while pressing the trigger, and a square edge caught on insulated gloves. The team switched to a pistol-grip shape with the probe at the nose and the OLED on an angled top surface. The enclosure measured 168 millimeters from probe tip to battery base. It used a 2-millimeter PC/ABS shell, a TPU grip strip, an M12 metal probe collar, and a battery door secured by two captive screws. The probe collar let the sensor head be replaced after field damage. A short molded lip protected the 40-kilohertz element without closing its acoustic path. The product manager imported a STEP model for the piezo housing and placed it against the board. The sensor lead passed close to the switching regulator, so the team moved the board's power section toward the grip and kept the amplifier at the nose. An X-ray view showed that the OLED connector sat beneath the display window. The team shortened a standoff and widened the trigger clearance by 1.5 millimeters. The case designer added a recessed USB-C port and a narrow opening for the speaker. The battery door had to open without removing the probe or display. A strength simulation helped compare the grip ribs around the screw bosses. The product manager checked that the TPU strip remained flush with the hand surface and that the trigger moved freely through its full travel. ## Turn the bench circuit into a field assembly The design review moved from the individual boards to the complete assembly. The Flux agent created the circuit and layout, maintained the BOM, and linked board changes to the enclosure cutouts and mounts. The product manager adjusted the trigger label manually, then inspected the sensor path from the probe to the converter. The electrical engineer ran design rule checks on the four-layer board and reviewed the battery protection circuit. The manufacturing route was chosen around the pilot, not a future catalog launch. the maker planned an assembled PCB run and an MJF nylon shell for the ten field units. The mechanical engineer kept the display bezel as a separate insert, which allowed the team to try a matte lens without reprinting the handle. They exported STEP and board assembly data from the same revision. ## Three requests that drove the prototype > Turn this 40-kilohertz leak-detector breadboard into a portable tool for plant maintenance technicians. Show an ultrasonic level, give a clear trigger-and-hold action, and run through a full shift from a protected 18650 cell. > Place the piezo input, TLV9062 gain stage, ADS8866, STM32G474, and OLED on a four-layer board no larger than 62 by 38 millimeters. Keep switching power away from the sensor input and expose test points for the amplifier and ADC. > Build a pistol-grip assembly around the imported probe STEP. Keep the M12 collar replaceable, protect the sensor opening, clear the OLED connector, and leave 1.5 millimeters of travel around the trigger. ## The team had something technicians could judge The product manager and the electrical engineer completed the connected design review in an afternoon. They checked the board against the piezo model, the trigger against the case, and the battery access against the service plan. A first article could be assembled from the approved BOM, while the MJF shell let staff test grip and probe access before a production tool was cut. The boxed prototype contained the piezo receiver, low-noise amplifier, converter, STM32G4 controller, OLED, speaker, protected battery, and USB-C charging circuit. Its mechanical design included the replaceable M12 probe collar, pistol grip, PC/ABS shell, TPU contact strip, trigger, display bezel, and captive battery door. The technician could hold the unit by the grip, bring the probe tip to a fitting, and read the signal without watching a laptop. The pilot exposed a useful preference: technicians wanted the bar graph visible while the trigger was held, but they did not want a loud tone in a shared workshop. The product manager changed the feedback requirement to a short confirmation beep followed by a visual reading. That decision remained connected to the board's speaker and the display window, so the next revision kept both interfaces in view. The lesson for a product manager is to treat the enclosure as part of the first prototype, not as packaging for a finished circuit. Grip, probe direction, display angle, and battery access affected the board outline. The board's connector positions and hot components shaped the grip. A physical assembly brought those choices into the same review. ## A breadboard-to-box checklist - Observe the operator's task and write down the required action and feedback. - Turn breadboard wires into named circuit interfaces and check each datasheet. - Choose battery, board size, probe, display, and control locations together. - Review the board inside the case with real STEP models and X-ray view. - Check trigger movement, grip strength, sensor opening, charging port, and battery service. - Select a prototype route and export one coordinated board-and-case revision. [Start your project at flux.ai](https://www.flux.ai/) ## About the author [Matthias Wagner](https://www.flux.ai/natarius) Founder & CEO at Flux Matthias is the Founder and CEO of Flux, a hardware design platform that's revolutionizing how teams create and iterate on circuits. Find him on Flux [@natarius](https://www.flux.ai/natarius). Let’s start building Build your big idea together with Flux. All you need to do is describe what you want to make, or what problem you want to solve. Flux will work with you to make it a reality. ![Close-up photo of a PCB made with Flux, with an ESP32 module, buttons, and a microSD slot.](https://www.flux.ai/p/assets/blogs/miscellaneous/sidebar-cta-pcb.webp) [Try it Free](https://www.flux.ai/signup) ## Related Content [ ![Line illustration of a circuit board inside an open enclosure where one old chip is lifted out and a new replacement chip lowers into place, with dashed fit lines showing the board still matches the enclosure mounting posts](https://www.flux.ai/p/assets/blogs/revive-product-end-of-life-parts-enclosure-fit/main.webp) ### Reviving a Product With End-of-Life Parts: Redesigning the Board Without Breaking the Enclosure Fit 5 Min Read](https://www.flux.ai/p/blog/revive-product-end-of-life-parts-enclosure-fit)[ ![Line illustration of a small round smart home door sensor in exploded view](https://www.flux.ai/p/assets/blogs/first-founder-smart-home-sensor-board-case/main.webp) ### From Idea to Pre-Orders: How a First-Time Founder Designed a Smart Home Sensor, Board and Case 5 Min Read](https://www.flux.ai/p/blog/first-founder-smart-home-sensor-board-case)[ ![Line illustration of a smart wristband wearable in exploded view](https://www.flux.ai/p/assets/blogs/trade-show-wearable-electronics-enclosure-six-weeks/main.webp) ### How a Startup Built a Trade-Show-Ready Wearable, Electronics and Enclosure, in Six Weeks 6 Min Read](https://www.flux.ai/p/blog/trade-show-wearable-electronics-enclosure-six-weeks)[ ![Line illustration of a filled progress bar leading to a consumer gadget in exploded view and stacked shipping boxes](https://www.flux.ai/p/assets/blogs/funded-campaign-to-manufacturable-hardware/main.webp) ### From Funded Campaign to Manufacturable Product: A Hardware Crowdfunding Playbook 5 Min Read](https://www.flux.ai/p/blog/funded-campaign-to-manufacturable-hardware)[ ![Line illustration of an old industrial controller module beside a new replacement board, dashed alignment lines matching identical connector positions and mounting holes, a DIN rail enclosure behind](https://www.flux.ai/p/assets/blogs/replace-obsolete-industrial-controller/main.webp) ### Replacing an Obsolete Industrial Controller: Matching the Original Connectors, Mounting Holes and Enclosure 5 Min Read](https://www.flux.ai/p/blog/replace-obsolete-industrial-controller)[ ![Line illustration of a benchtop lab instrument enclosure with a front panel display and knobs, its cover lifted to show the circuit board, next to a lab flask and a sample tray](https://www.flux.ai/p/assets/blogs/custom-lab-instrument-without-vendor-lead-time/main.webp) ### Custom Lab Instruments, Electronics and Housing, Without the Vendor Lead Time 5 Min Read](https://www.flux.ai/p/blog/custom-lab-instrument-without-vendor-lead-time) See All (6) ## Let’s start building. Let’s build your idea together. All you need to do is describe what you want to make, or what problem you want to solve. Flux will work with you to make it a reality. [Try it Free](https://www.flux.ai/signup) ![Close-up of a Flux-designed printed circuit board](https://www.flux.ai/p/assets/homepage-v2/mission-visual.webp)